• Plant Journal
• /
• v.14 no.2
• /
• pp.33-38
• /
• 2018

The CFB boilers technology is facing a number of challenges. Among them, boiler tube erosion, sintering by bed inventory overheating and high self consumed service power are major ones. This study was conducted to obtain allowable bed inventory with the Yeosu Power Plant, a 300 MW class CFB boiler. For the test, bed pressure was reduced from design pressure of 4.5 KPa to 2.5 KPa by reducing bed inventory, at fixed turbine output, coal consumption rate and air flow. Consequently, reducing the lower bed inventory is effective to decrease bed temperature but excessive reducing might increase bed temperature due to lack of circulating fluidized materials. Also, in case of the Yeosu Plant boiler using subbituminous coal as its primary fuel, its bed temperature change is highly affected by not only the amount of bed inventory, but also the boiler capacity and coal contents.

• Journal of the Korean Society of Combustion
• /
• v.7 no.4
• /
• pp.10-20
• /
• 2002

This paper discusses effect of solid mass inventory on the hydrodynamic characteristics of circulating fluidized bed(CFB). Operating parameters of solid mass inventory and air flow rates were varied to understand their effects on fludization pattern. Experimental measurements were made in a CFB of which height and diameter are 3m and 0.05m respectively. Black SiC particles ranging from $100{\mu}m\;to\;500{\mu}m$ were employed as the bed material. Superficial gas velocity of riser and J-valve fluidizing velocity were in the ranges of $1.39{\sim}3.24m/s\;and\;0.139{\sim}0.232m/s$, respectively. The axial solid fraction and solid circulation rate of CFB were calculated based on the experimental data and compared with modellings through IEA-CFBC Model and commercial CFD code.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.165-172
• /
• 2002

This paper discusses hydrodynamic characteristics of cold circulating fluidized bed(CFB) in different solid mass inventories. Operating parameters of solid mass inventory, primary air and J-valve fluidizing air were varied to find out the effect on the flow fludization pattern. Experimental measurements were made in a 3m tall CFB that has 0.05m riser diameter and black silica-carbonate of particle sizes from $100{\mu}m$ to $500{\mu}m$ were employed as the bed material. The operating conditions of superficial gas velocity and J-valve fluidizing velocity were in the ranges of 1.39~3.24 m/s and 0.139~0.232 m/s respectively. The axial solid fraction and solid circulation rate of CFB were observed and compared with modelling through IEA-CFBC Model and commercial CFD code.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.1
• /
• pp.49-55
• /
• 2012

Hydrogen isotopes accountancy and storage are important functions in a nuclear fusion fuel cycle. The hydrogen isotopes are safely stored in metal hydride beds. The tritium inventory of the bed is determined from the decay heat of tritium. The decay heat is measured by circulating helium through the metal hydride bed and measuring the resultant temperature increase of the helium flow. We are reporting our preliminary experimental results on the hydrogen isotopes accountancy and storage performance in a metal hydride bed.

• Journal of Preventive Medicine and Public Health
• /
• v.16 no.1
• /
• pp.113-120
• /
• 1983

The main objective of this case study is to develop demand forecasting model for durg inventory control in a university hospital. This study is based on the pertinent records during the period of January 1975 to August 1981 in the pharmacy and stock departments of the hospital. Through the analysis of the above records the author made some major findings as follows: 1. In A.B.C. classification, the biggest demand (A class) consists of 9 items which include 6 items of antibiotics. 2. Demand forecasting level of an index or discrepancy in A class drug compared with real demand for 6 months is average 30.4% by X-11 Arima method and 84.6% by Winter's method respectively. 3. After the correcting ty the number of bed, demand forecasting of drug compared with real demand for 6 months is average 23.1% by X-11 Arima method and 46.6% by Winter's method respectively.

• Clean Technology
• /
• v.20 no.4
• /
• pp.359-366
• /
• 2014

Attrition characteristics of PKM1-SU particles, $CO_2$ absorbents for pre-combustion $CO_2$ capture process, and FCC particles, catalytic particles for hydro cracking of crude oil, were investigated at high temperature and high pressure conditions. Particle attrition tests were executed at various kinds of temperature ($0-400^{\circ}C$) and pressure (0-20 bar) conditions in a cylinder type bubbling fluidized bed with 15.1 cm diameter, 120 cm height and 1 mm orifice-sparger tube. Attrited particles before and after tests were analyzed by BET, optical microscopy, and particle size analyzer. Effects of bed material height (solid inventory) and steam injection were also verified by using ASTM D5757-95, conventional attrition test method.

• Korean Chemical Engineering Research
• /
• v.54 no.5
• /
• pp.678-686
• /
• 2016

The effect of internal and shroud nozzle distributor to bubbling fluidized beds which has the size of $0.3m-ID{\times}2.4m-high$ column was modeled by CPFD (Computational Particle-Fluid Dynamics). Metal-grade silicon particles (MG-Si) were used as bed materials which have $d_p=149{\mu}m$, ${\rho}_p=2,325kg/m^3$ and $U_{mf}=0.02m/s$. Total bed inventory and static bed height were 75 kg and 0.8 m, respectively. Effect of vertical internal on the bubble rising velocity was investigated. Bubbles were split by internal when the axial position of the internal from the distributor, z = 0.45 m. Bed pressure drop and axial solid holdup were not affected by internal. However, in the case that axial distance of internal from distributor was too close to jet penetration length, bubbles were not separated and bypassed internal, and faster than without internal or z = 0.45 m.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.185-192
• /
• 2010

The chemical-looping combustion(CLC) has advantages of no energy loss for separation of $CO_2$ without $NO_x$ formation. This CLC system consists of oxidation and reduction reactors where metal oxides particles are circulating through these two reactors. In the present study, the reaction kinetic equations of iron oxide oxygen carriers supported on bentonite have been determined by the shrinking core model. Based on the reactivity data, design values of solid circulation rate and solids inventory were determined for the rector. Two types of interconnected fluidized bed systems were designed for CLC application, one system consists of a riser and a bubbling fluidized bed, and the other one has a riser and two bubbling fluidized beds. Solid circulation rates were varied to about $30kg/m^2s$ by aeration into a loop-seal. Solid circulation rate increases with increasing aeration velocity and it increases further with an auxiliary gas flow into the loop-seal. As solid circulation rate is increased, solid hold up in the riser increases. A typical gas leakage from the riser to the fluidized bed is found to be less than 1%.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.2
• /
• pp.168-178
• /
• 2009

To check feasibility of SEWGS(Sorption Enhanced Water Gas Shift) system, conceptual design and sensitivity analysis of operating variables have been investigated based on a design program of two-interconnected fluidized bed. Based on the conceptual design results, the optimum configuration for SEWGS was considered. Among three configurations, bubbling beds system was selected as the best configuration. Process design results indicate that the SEWGS system is compact and feasible. Based on the selected operating conditions, the effects of variables such as pressure, $CO_2$ capture capacity, solid inventory, CO conversion and $CO_2$ capture efficiency have been investigated as well.

• Health Policy and Management
• /
• v.4 no.1
• /
• pp.123-137
• /
• 1994

The objectives of this research is to find the factors which determined hospital profitability. The unit of analysis is hospital, and the data is collected from two sources. One source is derived from Ministry of Health and Social Affairs(4 years' data from 134 hospitals), and another source is derived from Sam-II Accounting Co.(1 year's data from 37 hospitals). Hospital profitability, which is dependent variable in our research, is measured with financial ration, such as ROI(reture on investment). The major findings are as follows; 1) The hospital profitability is determined with not hospital type itself but management-incentives associated with hospital type. 2) The maximum profitability is obtained in 775 bed-size. 3) The hospital location isn't a factor to determine profitability 4) The internal control and management, such as account receivables, inventory, fixed assert investment, is major factor to hospital profitability.