• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.48-55
• /
• 1997

The ball bearing with thin-section raceways which is much lighter than other conventional bearings used in most modem passenger cars and small tracks. The important design parameters of this bearing is the groove radius of raceways, the diametral clearance, the free contact angle and so on. The optimal value of these parameters were determined by considering the dynamic load capacity, the contact angle and the calculated fatigue life. The contact angle between a ball and raceways was calculated by considering the local contact deformation and the structural deformation of thin-section raceways which was estimated by FEM. The raceways were made by means of the press-forming process. The fatigue life tester was designed and manufactured. The fatigue life test was executed and the reliability of this bearing was confirmed.

• Tribology and Lubricants
• /
• 제8권1호
• /
• pp.70-77
• /
• 1992

Al-Pb-Si bearing alloys were produced by a forced stirring method and a rapid solidification process to study wear properties of bearing alloys. A homogeneous distribution of Pb particles in Al matrix could be obtained by means of the forced stirring and the rapid cooling during the casting. The wear properties of bearing alloys were tested by a pin-on-disc wear tester. The change in microstructure according to the alloy manufacturing variables was observed by the backscattered electron images. Al-Pb and Al-Si binary alloys showed a transition from mild to severe wear. The transition was not found in Al-Pb-Si ternary alloys. It could be concluded that the lubricatioin effect of Pb and the strengthening effect of Si in the ternary alloys enhanced the bearing properties. A Al-25%Pb-13%Si alloy showed the lowest coefficient of friction in this experiment. It indicated that the optimum concentration of alloy was 25% Pb and 13% Si when the forced stirring of melt and water-cooled-copper-mold solidification were adopted.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.21-22
• /
• 2005

A study on the wear characteristics of the white metal(Sn-base alloy) bearing as a function of particle contamination level was conducted in order to establish control criteria of the lubricant in the 2-stroke marine diesel engine. Particle contamination level of the lubricants ranged from NAS 10 to 12 for the experiments. Bar-on-plate type wear test was performed using reciprocating wear tester. Based on this study it was found that there was no noticeable difference in weight loss of the white metal for NAS10 and NAS11(particle contamination level). Surface roughness of the white metal bearing after the wear test of 8hrs for the highly contaminated lubricant(NAS12 level) was up to $6{\mu}m$ in Rmax whilst that of the less contaminated lubricants(NAS10 & 11) was less than $1.5{\mu}m$ in Rmax.

• 한국안전학회지
• /
• 제31권1호
• /
• pp.13-18
• /
• 2016

KTX wheelset bearings have thus far been maintained in accordance with the maintenance system of French national railway company, SNCF. The overhaul cycle time (OCT) of KTX wheelset bearings is now 1.4 million km in mileage. This value, however, has not been validated in Korea that has much different railway environments with France. In fact, it is impossible to validate OCT of wheelset bearings directly because they are disassembled and cleaned only when some faults are detected. In this paper, the accuracy of the current OCT value was evaluated indirectly by investigating the effect of grease lubricants on the bearing life. Five grease samples (one new and four aged greases) were used in this study. Four aged greases of different conditions were obtained from four wheelset bearings whose mileages were about 0.3, 1.2, 1.3, and 1.8 million km, respectively. Each grease sample was then injected into the RCF (Rolling Contact Fatigue) tester and fatigue lifetime was experimentally estimated. In addition, the wt% of Fe in each grease sample was analysed. The experiment results reveal that the bearing lifetime is inversely proportional to the mileage of grease sample while the wt% of Fe increases with the mileage of grease sample. Based on the experimental results, it can be concluded that the current OCT value is appropriate for the first overhaul of wheelset bearings. However, further validation is required to determine the second and third OCT values.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.590-595
• /
• 2006

This paper presents the friction and anti-wear characteristics of nano-oil with a mixture of a refrigerant oil and carbon nano-particles in the thrust slide-bearing of scroll compressors. Frictional loss in the thrust slide-bearing occupies a large part of total mechanical loss in scroll compressors. The characteristics of friction and anti-wear using nano-oil are evaluated using the thrust bearing tester for measuring friction surface temperature and the coefficient of friction at the thrust slide-bearing as a function of normal loads up to 4,000 N and orbiting speed up to 3,200 rpm. It is found that the coefficient of friction increases with decreasing orbiting speed and normal force. The friction coefficient of carbon nano-oil is 0.015, while that of pure oil is 0.023 under the conditions of refrigerant gas R-22 at the pressure of 5 bars. It is believed that carbon nano-particles can be coated on the friction surfaces and the interaction of nano-particles between surfaces can be improved the lubrication in the friction surfaces. Carbon nano-oil enhances the characteristics of the anti-wear and friction at the thrust slide-bearing of scroll compressors.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.645-649
• /
• 1997

In case of swash plate type axial piston hydraulic motor, hydrostatic bearing used to achieve the lubrication effect on the mechanical sliding contact areas between the following parirs ; sliooer-pad and swash plate,piston and cylinder bore,valve plate and cylinder block, etc. This study discussed the basic charateristic for the hydrostatic slipper-pad bearings with the capillary or orifice restrictor under static load condition. And, we also development of hydrostatic bearing tester for hydrostatic balancing test of pistion & slipper-pad assembly, and some experimental data on supply pressure step responce are reported.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.309-310
• /
• 2006

This paper is about the development of surface inspection of bearing inner and outer race using machine vision. Before this system is developed, most inspections are performed by workers' naked eye. To improve both the inconvenience and incorrectness, another new tester is introduced. This system has the three sections mainly. First one is the mechanism section which transfers bearing manufactured from previous process line to the testing process in plant. Another is the inspection system which is composed of two parts: computer vision and measurement system using laser diode which inspects the defects of the bearing inner or outer race. The other is the pneumatic cylinder part controlled by Programmable Logic Controller(PLC). The system which is developed shows favorable results, and that has the advantage of convenience and correctness compared to previous system.

• Tribology and Lubricants
• /
• 제15권2호
• /
• pp.171-177
• /
• 1999

Many lubricated systems experience boundary lubrication condition during operation. However, the friction and wear characteristics of boundary lubrication are not clearly understood. In this work the factors which affect the friction and wear between boundary lubricated metallic surfaces are investigated. Experiments were performed using a pin-on-disk type tester with pure aluminum, pure copper, and SM45C steel as the disk material and steel, stainless steel and bearing ball as the ball. The experimental conditions were determined according to the Taguchi experimental method. From the experimental results, the major factors that influence the friction and wear characteristics of boundary lubrication could be identified.

• Tribology and Lubricants
• /
• 제22권5호
• /
• pp.269-275
• /
• 2006

Rolling bearings are classified one of the most important machine elements. The various function of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required to improve bearing lubrication. Three urea/ether oil greases with different composition were synthesized to compare the performance of these greases. The typical grease physical properties were investigated, and life test of these greases was conducted by FE-9 grease life tester. The grease with higher content of the thickener showed higher performance. After these preliminary test, twelve greases were synthesized and evaluated the performance of dropping point and OIT value. And optimized conditions for grease synthesis were selected by SSRED (Six Sigma Robust Engineering Design) using dropping point and OIT value respectively. The optimized grease using OIT value showed longer grease life than that using dropping point. Two greases were synthesized following the optimum synthesis conditions by means of OIT value. Then grease life and other properties of these greases were investigated. These two greasaes showed longer grease life than typical urea/ether oil grease.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.123-129
• /
• 2004

Rolling bearings are assorted one of the most important machine elements. The various functions of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required to improve rolling bearing lubrication. The two conditions for optimum grease synthesis were selected by SSRED (Six Sigma Robust Engineering Design) program by using dropping points and OIT values respectively. And the optimized two urea/ether oil greases were synthesized to compare the performance. The typical physical properties of grease were investigated. And life test of these greases was conducted by rolling bearing grease life tester The characteristics of the greases before and after life test were investigated using FTIR, microscope, SEM, TG/DSC, OIT and TAN meter The optimized two greases showed longer life time than typical urea/ether oil grease. The optimized grease by means of OIT value showed higher performance such as long life time. low TAN value and high oil bleeding amount in comparison with the optimized grease using dropping point.