• 문화기술의 융합
• /
• 제6권4호
• /
• pp.753-760
• /
• 2020

본 연구에서는 정밀 3차원 수치해석모델을 이용하여 수직하중(받침설계하중)과 수평하중(지진시 발생되는 수평력)을 적용하여 교량받침 교체시 보자리의 구조적 안전성에 대한 검토를 수행하였다. 기존 콘크리트와 교량받침 교체로 인해 새로 타설된 콘크리트의 응력 및 용접된 철근에 발생하는 응력 및 변위 결과를 수치해석적으로 확인하였다. 수치해석결과, 수평력 및 보자리 높이 증가는 신구콘크리트 경계면의 발생응력의 증가에 따른 콘크리트 균열(파괴) 및 내부 철근연결부의 응력증가를 초래하는 것으로 분석되었다. 따라서 보자리 높이 증가는 수평력의 크기와 직접적인 상관관계가 있으며 받침 용량에 적합한 보자리 높이 적용이 필요할 것으로 분석되었다. 본 연구에서는 보자리에 작용하는 수평력의 크기와 보자리 높이와의 상관관계를 변수로한 받침교체공사 가이드라인을 도표로 제시하여 교량받침 용량에 적합한 보자리 높이 설정 및 보강유무를 결정하는 방안을 제시하였다.

• Safety and Health at Work
• /
• 제10권3호
• /
• pp.314-320
• /
• 2019

Background: Sitting posture may be related to risk factors, including inadequate weight-bearing support, particularly when maintained for long periods. Considering that body weight is loaded in a closed support system composed of the seat, backrest, floor and working surface, the aims of the present study were to describe the development of an ergonomic sitting workstation to continuously record weight-bearing at the seat, chair, backrest, work surface, and floor and to test its measurement properties: reproducibility, criterion-related validity, and sensitivity. Methods: Rigid bodies (1 to 30 kg) and participant weights were recorded to evaluate the workstation measurement properties. Results: Rigid body tests showed variation values less than 0.050 kg on reproducibility test and errors below 5% of measured value on criterion validity tests. Participant tests showed no statistically significant differences between repeated measures ($p{\geq}0.40$), errors were less than 2% of participant weights an sensitivity presented statistically significant changes (p = 0.007). Conclusion: The sitting workstation proposed showed to be reliable, valid and sensitive for use in future ergonomic studies to evaluate the sitting posture.

• Earthquakes and Structures
• /
• 제10권6호
• /
• pp.1467-1486
• /
• 2016

This research focuses on seismic performance of a class of single pier skewed bridges with three different pier-deck connections; skew angles vary from $0^{\circ}$ to $60^{\circ}$. A well-documented four span continuous deck bridge has been modeled and verified. Seat-type connections with fixed and sliding bearings plus monolithic pier-deck connections are studied. Shear keys are considered either fully operational or ineffective. Seismic performances of the bridges and the structural components are investigated conducting bidirectional nonlinear time history analysis in OpenSees. Several global and intermediate engineering demand parameters (EDP) have been studied. On the basis of results, the values of demand parameters of skewed bridges, such as displacement and rotation of the deck plus plastic deformation and torsional demand of the piers, increase as the skew angle increases. In order to eliminate the deck collapse probability, the threshold skew angle is considered as $30^{\circ}$ in seat-type bridges. For bridges with skew angles greater than $30^{\circ}$, monolithic pier-deck connections should be applied. The functionality of shear keys is critical in preventing large displacements in the bearings. Pinned piers experience considerable ductility demand at the bottom.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.37-43
• /
• 2019

This paper presents an optimization method to determine the shoulder height of an angular contact ball bearing by 3D contact analysis using nondimensional-shaped variables. The load analysis of the ball bearing is performed to calculate the internal load distributions and contact angles of each rolling element. From the results of bearing load analysis and the contact geometry between the ball and inner/outer raceway, 3D contact analyses using influence function are conducted. The nondimensional shoulder height and nondimensional load are defined to give the generalized results. The relationship between the shoulder height and radius of curvature of the shoulder under various loading conditions is investigated in order to propose a design method for the two design parameters. Using nondimensional parameters, the critical shoulder heights are optimized with loads, contact angles, and conformity ratios. We also develop contour maps of the critical shoulder height as functions of internal loads and contact angles for the different contact angles using nondimensional parameters. The results show that the dimensionless shoulder height increased as the contact angle and dimensionless load increased. Conversely, when the conformity ratio increased, the critical shoulder height decreased. Therefore, if the contact angle is reduced and the conformity ratio is increased within the allowable range, it will be an efficient design to reduce the shoulder height of ball bearings.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.46-54
• /
• 2014

The hollow design of a railway axle is one of the most effective methods to reduce the weight of an axle. However, the conventional hollow axle has the limitation of a lightweight design because it has the same bore diameter along the axial position. The new type of railway axle, the tapered inner surface railway axle, has a different inner diameter between the journal bearing seat and wheel seat. This design method is one way to increase the weight reduction possibility. The purpose of the present study is to establish and evaluate the design of the tapered inner surface railway axle. The case study and Finite Element Method(FEM) are applied to evaluate the strength of the lightweight railway axle according to the European Norm(EN 13103). Finally, the best design case for reducing the weight of the axle is drawn from the results of the case study.

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.314-319
• /
• 2006

In this paper, the friction and wear characteristics of contact type sealing unit far a water turbine have been presented. The sealing unit for a small hydropower generation is to stop a leakage of circulating water from an outside of an impeller to an inside of a rolling bearing. The friction heating between a seal ring and a seal seat may radically increase a surface temperature in which increase a power loss and wear on the rubbing surface. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Victors hardness and the hardness of silicone carbide of SiC is 714.1 in Victors hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces are a dry friction, a water film friction and a mixed friction that is contaminated by a dust, silt, and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat in primary sealing unit. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components.

• Steel and Composite Structures
• /
• 제39권4호
• /
• pp.383-399
• /
• 2021

In the study, three 1:3-scale unequal span steel-concrete composite substructures with top-seat angle and double web angle connection were designed and identified as specimens GTSDWA-0.6, GTSDWA-1.0, and GTSDWA-1.4. Pseudo-static tests and refined numerical model analysis were conducted to examine the anti-progressive collapse performance of a semi-rigid steel-concrete composite substructure. The results indicated that the failure modes of the three specimens revealed that the fracture occurred in the root of the long leg of the top/seat angle in tension at the connection. With increases in the span ratio of the left and right composite beams, the bearing capacities of the composite substructures decreased, and the corresponding displacement increased. With respect to GTSDWA-0.6 and GTSDWA-1.4, the resistance due to the short composite beam corresponded to 62% and 60%, respectively, and the total resistance provided by the short composite beam exceeded that of the long composite beam. With respect to GTSDWA-1.0, the resistance due to the left and right composite beams was similar. All three specimens underwent the flexure mechanism and flexure-axial mixed mechanism stages. They resisted the external load mainly via the flexure mechanism. Moreover, the addition of stiffeners on both sides of the top and seat angles is advantageous in terms of improving the collapse resistance and ductility of unequal span composite substructures.

• Steel and Composite Structures
• /
• 제42권6호
• /
• pp.791-804
• /
• 2022

As a type of semi-rigid connection, the top and seat angle connections are popular in current structures owing to their good cyclic performance and simple erection. However, their stiffness and load bearing capacity are relatively insufficient. This study proposes two strengthening methods to further increase the stiffness and strength of bolted-angle joints while maintaining satisfactory energy dissipation capacity (EDC) and ductility. Cyclic loading tests were conducted on six joint specimens with different strengthened angle components. Based on the test results, the influence of the following important factors on the cyclic behavior of steel joint specimens was investigated: the position of the rib stiffeners (edge rib stiffeners and middle rib stiffener), steel strength grade of rib stiffeners (Q345 and Q690), and additional stiffeners or not. In addition, the finite element models of these specimens were built and validated through a comparison of experimental and numerical results. The stiffness and bearing capacity of the bolted-angle joints could be improved significantly by utilizing the novel strengthened joints proposed in this study. Moreover, this can be achieved with almost no increase in the amount of steel required, and the EDC of this joint could also satisfy the requirements of seismic codes from various countries.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.19-26
• /
• 2021

교량 받침장치부는 상부구조의 수직하중을 지지하여 하부구조에 전달하고, 교량의 붕괴사고를 방지하는 역할을 한다. 하지만, 포항지진에 의하여 총 12개 도로교량의 받침장치 몰탈 파손, 받침장치 파손 및 쐐기 손상이 보고되었다. 본 연구에서는 지진시 교량 받침장치부의 구조 시스템 특성을 고려하여 교각의 코핑부와 무수축몰탈을 포함한 면진받침 장치 실험체의 전단 거동특성 및 손상모드를 평가하였다. 받침장치 쐐기에 대한 영향을 확인하기 위하여 쐐기 설치 유무를 변수로 설정하였으며, 압축-전단 실험을 실시하여 면진장치의 전단 거동특성과 손상모드를 확인하였다. 또한 유한요소해석을 통하여 받침장치의 거동특성 및 각 구성요소별 손상원인을 분석하였다. 실험결과, 쐐기의 충돌 및 손상 발생 이후 급격한 하중변화가 발생하였으며, 받침장치와 무수축몰탈 경계부를 따라 균열이 발생하였다. 쐐기 유무에 따른 쐐기, 앵커 소켓 및 무수축볼탈의 응력거동을 비교함으로써 지진시 교량받침장치부의 손상원인을 규명하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권5호
• /
• pp.47-54
• /
• 1991

The lip seals widely used nowadays in stern tube sealing system of ships have radial sealing contact with shafts or liners, on the other hand the face seals of stern tube sealing system have axial sealing contact with seat. Because of axial sealing contact, the face seals have a large number of merits such as durability of life, simplicity of structure, easy fitting and replacement, etc. In this paper, for the purpose of development of face seals, the fundamental properties of axial sealing contact were analyzed and a trial face seal was designed and manufactured using N.B.R. rubber and Thordon which is widely used for bearing materials. The seal proper of trial face seal was made from N.B.R. rubber and the face insert was made from Thordon, thermosetting resins which are three dimensional, cross linked condensation polylmers. The performance test of trial face seal was carried out on the test bench which was specially designed and manufactured. The results were satisfactory enough to be used in practical stern tube sealing system.