• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.257-262
• /
• 2001

A numerical analysis is undertaken to show tile influence of bearing design parameters on tile load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, arid the seal ratio.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.218-227
• /
• 1998

Present study is undertaken to optimize the lubrication reliability and frictional loss of the dynamically-loaded journal bearing in hermetic reciprocating compressor with alternative refrigerant R600a application. Thermodynamic and dynamic analysis has been conducted to investigate cylinder pressure variations by substitution alternative refrigerant R600a for R12. The modeling of the dynamics of the compressor mechanism has been performed with lumped mass method. A mathematical model is developed for analyzing the dynamics of the journal bearing system with the mobility method. It takes into account the effects of the refrigerant species, aspect ratio, clearance ratio and surface roughness. A corresponding computer program is described which enables to obtain the minimum film thickness and frictional loss. Design optimization is graphically performed by parametric studies of the aspect ratio and clearance ratio.

• 한국지반공학회논문집
• /
• 제20권8호
• /
• pp.41-48
• /
• 2004

이 연구에서는 아직 국내에서는 시공실적이 없는 쇄석다짐말뚝(Gravel Compaction pile)공법의 적용성을 판단하기 위하여 SCP와 GCP의 모형토조시험을 수행하였다. 즉, 원통형 압밀상자(지름 20cm, 높이 40cm)에 치환율 30, 40, 50, 60, 70%로 달리 조성하여 원심력 압밀시험기를 이용하여 압밀시킨 후, 재하시험을 통하여 두 공법의 지지력 특성을 비교 검토하였다. 또한 모형시험을 통해 얻어진 극한지지력을 기존에 제안된 SCP 및 GCP 시공지반의 극한지지력 산정식을 이용한 계산값과 비교하였다. 모형시험 결과 GCP 시공지반이 SCP 시공지반에 비해 지지력 측면에서 더 우수한 것으로 나타났다.

• KSTLE International Journal
• /
• 제2권1호
• /
• pp.1-11
• /
• 2001

The influence of aerated oil on a high-speed journal bearing is examined by classical thermohydrodynamic lubrication theory coupled with analytical models for viscosity and density of air-oil mixture in fluid-film bearing. Convection to the walls and mixing with supply oil and re-circulating oil are considered. With changing eccentricity ratio, it is investigated the effects of air bubbles on the performance of a high-speed plain journal bearing. Just at the moderate eccentricity ratios, even if the involved aeration levels are not so severe and the entrained air bubble sizes are not so small, it is found that the bearing load and friction force may be changed so visibly for the high speed bearing operation.

• Tribology and Lubricants
• /
• 제4권1호
• /
• pp.69-73
• /
• 1988

The effects of journal speed and bearing load on pressure distribution and the temperature distribution of bearing surface are investigated experimentally. The journal bearing which has 219.94mm diameter, length-to-diameter ratio of L/D=0.8 and clearance ratio of 0.004 is used. Journal has a built-in pressure transducer for the measurement of pressure distribution in the mid plane of bearing. Bearing surface temperatures are measured at 60 points. The bearing load is varied from 300 N to 5900 N and journal speed from 300 rpm to 2500 rpm. As the load is increased under constant speed, the location of maximum pressure moves to the site of minimum film thickness, and maximum pressure and absolute value of minimum pressure are increased. The temperature distribution in vicinity of oil inlet shows that heated lubricant's carry-over exists around the oil inlet.

• 산업기술연구
• /
• 제27권A호
• /
• pp.121-130
• /
• 2007

Centrifuge model tests were performed to find appropriate equations proposed previously of estimating the bearing capacity of the composite clayey soil reinforced with sand compaction pile. Model tests were carried out with changing the replacement ratio of SCP (20%, 40%, 70%), contents of fine materials (5%, 10%, 15%) and ratio of treated width to loading width (1B, 2B, 3B). Test results about bearing capacity of the composite ground were obtained by performing the surcharge load tests with measurements of applied loads and vertical displacement. Bearing capacities against bulging and shear failures were estimated by the existing equations. As results of comparing the estimated bearing capacity with experimental values the bearing capacities estimated by Greenwood's equation (1970) for bulging failure mode were similar to the test results.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권1호
• /
• pp.198-208
• /
• 2011

연약 점성지반 위에 상대적으로 낮은 하중의 구조물이 얹어질 때, 상부에 모래층을 두어 지지력을 증진시킬 수 있다. 이와같은 점토 위 모래층이 놓이는 조건에 대한 지지력 검증은 현장에서 평판재하시험 등을 통해 지지력 검증이 어렵기 때문에 설계단계에서부터 정확한 지지력 예측이 필요하다. 따라서, 본 연구는 점토 위 모래층이 놓이는 지반의 지지력 거동을 파악하기 위해 2차원 실내토조실험과 FEM 해석을 수행하였다. 주요 인자로 깊이비 H/B와 지지력비 $q_c/q_s$를 선정하여, 모래층 높이, 점토의 비배수전단강도 그리고 재하 폭을 변수로 하였다. 그 결과, 실내토조실험은 FEM 해석과 적합성이 상당히 높게 나타났다. 이론식과의 비교에 있어서 보다 최신 연구인 Okamura et al.(1998)의 메커니즘보다 관입전단 메커니즘과 그 유사성이 크게 나타났으며, 하중확산 메커니즘의 적용성을 위하여 등가하중확산각을 제시하였다. 또한, $q_c/q_s$에 대하여 무차원 단위의 한계깊이비 $H_f$의 선형 회귀식을 제안하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.879-882
• /
• 1997

This paper aims to clarify the effect of the sol-gel sintered alumina grain and the PbO content of binder on the performance of the vitrified alumina stone for superfinishing the ball bearing race with the vitrified alumina superfinishing stone. The main conclusions obtained were as follows. The stone that contain 8- 11% PbO in binder shows the highest grinding ratio, and increasing or decreasing the PbO contents causes lower grinding ratio. When superfinishing with the stone using the 45% fused alumina and 55% sol-gel sintered alumina grain, the grinding ratio becomes the best, the other ratio of grain contents shows lower performance. With increasing the bending strength of stone, the grinding ratio becomes larger. The roughness of the finished surface is the lowest in case of using the stone of the above mentioned conditions.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• 한국산학기술학회논문지
• /
• 제16권2호
• /
• pp.1477-1482
• /
• 2015

기초의 근입비가 보상기초의 극한지지력과 침하량에 미치는 영향을 살펴보고자 수치해석을 수행하였다. 수치해석에 의한 극한지지력비는 이론식에 의한 극한지지력비보다 컸으며 전체적으로 극한지지력비가 근입비에 비례하는 결과를 보였으나 정사각형기초에 대한 수치해석결과만 극한지지력비가 근입비에 따라 급격하게 증가하는 양상을 보였다. 모래지반에 놓인 띠기초의 경우 근입비에 따른 극한지지력비는 수치해석과 Meyerhof 방법에 의한 경우가 비슷하였으며 대체로 근입비의 제곱에 가까운 값을 나타내었으며 점토지반에 놓인 띠기초의 경우 이론식에 의할 경우 극한지지력비는 근입비의 영향을 크게 받지 않았고 수치해석결과에 따르면 근입비를 약간 상회하는 값들을 보였다. 수치해석결과에 따르면 근입비에 따른 정사각형기초의 극한지지력비가 띠기초의 그것에 비하여 크게 계산되었다. 수치해석결과를 통해 볼 때 전체적으로 근입비가 1인 경우 침하량비는 0.4 정도의 값을 보이다가 근입비가 커짐에 따라 침하량비가 감소하는 양상을 보였으며 느슨한 모래의 경우 상대적으로 침하량비가 가장 작았다.