• Journal of Korean Society of Steel Construction
• /
• v.15 no.3
• /
• pp.261-269
• /
• 2003

The length of the links in an eccentrically braced frame will dictate the behavior of the frame. Link length controls the yielding mechanism and the ultimate failure mode. For short links, the links' shear forces reach the plastic shear capacity before the end moments reach the plastic moment capacity, and the links yields in the shear, forming a shear hinges. These links are termed "shear links." For long links, the end moments reach the plastic moment capacity before the links' shear forces reach the plastic shear capacity, forming moment hinges. These links are termed moment links." In long links, flexural yielding dominates the response, and very high bending strains are required at the link ends to produce large link deformations. In a shear links, the shear force is constant along the length of the links, and the inelastic shear strain are is uniformly distributed over the length of the links. This permits the development of large inelastic link deformations without the development of excessively high local strains. However, The use of eccentrically braced steel frames for the purpose of architectural cionsiderations such as openings and doors, areis dictating the use of longer links, though. Little data areis available on the behavior of long links under cyclic loading conditions. In This paper documents the results of an experimental program is that was conducted to assess the response of moment links in eccentrically braced frames. Sixteen specimens awere tested using a cyclic load.

• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.71-79
• /
• 1995

For the fabrication of high sensitive intrinsic fiber optic Fabry-Perot interferometeric sensor, the deposition conditions of $TiO_{2}$ thin film used to the internal mirrors of the sensor were investigated. The $TiO_{2}$ film deposited by RF magnetron sputter had higher refractive index ($2.36{\sim}2.48$) and better stoiciometry (O/Ti = 2) than that deposited bye-beam evaporator. In the case of forming $TiO_{2}$ internal mirror by using fusion splicing technique, the $TiO_{2}$ reflection mirror deposited by RF magnetron sputter in the condition of 120W RF power showed high. reflectance and excellent controllability of reflection power. The fabricated intrinsic fiber optic Fabry-Perot interferometer with two $TiO_{2}$ internal mirrors deposited under the condition showed very stable fringe patterns. It is, therefore, expected that the interferometer will be applicable to various high precision sensors.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.6
• /
• pp.538-544
• /
• 2000

A phased array ultrasonic nondestructive inspection system is being developed to obtain images of the interior of steel structures by modifying a medical ultrasound imaging system. The medical system consists of 64 individual transceiver channels that can drive 128 array elements. Several modifications of the system were required mainly due to the change of sound speed. It was necessary to fabricate array transducers for steel structure and to obtain A-scan signal that is necessary for the nondestructive testing. Boundary diffraction wave model was used for the prediction of radiation beam field from array transducers, which provided guidelines to design array transducers. And a RF data acquisition board was fabricated for the A-scan signal acquisition along a selected un line within an image. For the proper beam forming in the transmission and reception for steel structure, delay time was controlled. To demonstrate the performance of the developed system and fabricated transducers, images of artificial specimens and A-scan signals for selected scan lines were obtained in a real time fashion.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1559-1562
• /
• 1999

We formed $SiO_2:F$ films by low-temperature process called Liquid Phase Deposition(LPD) and investigated its electrical and physical properties. Because of the use of room-temperature and no special vacuum apparatus for forming $SiO_2:F$ films, this technique can have some advantages related with the application to dielectric interlayer for multilevel structure in ULSI devices. The growth rate 100nm/hr was obtained at the growth solution of 2.5mol/l. The P-etch rate showed a similar or better tendency compared with $SiO_2$ films formed by CVD, Sputter, E-beam evaporator etc.. The fourier transform infrared (FTIR) spectra revealed that the contained fluorine atoms exist uniform throughout the formed $SiO_2$ films. The Scanning Electron Microscope images showed that LPD-$SiO_2$ films could be stably grown on silicon substrates and the good step-coverage could also be obtained, which indicates that the LPD-$SiO_2$ films have some possibility of the application to planarization and interlayer dielectric films which are vitally necessary to achieve the multilevel interconnection in ULSI. The I-V characteristics has some distinct differences according to the concentration of growth solution.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.5 s.78
• /
• pp.637-648
• /
• 2005

Innovative prestressed steel plate girders were presented in this study. Hot-rolled H beams were loaded first, then relatively high-strengthsteel plates were welded on the top and bottom flanges of preloaded H beams. Finally, high prestressed plate (HiPP) girder was manufactured by simply releasing prestresses of rolled beams. To verify prestress distributions induced in this girder, the experimental study was conducted and some guidelines to manufacture these girders effectively were addressed. In addition, methods to determine the allowable bending stress of HiPP girders and to check welding stresses were addressed for design of temporary bridges. The efficiency and effectiveness of the present girder were demonstrated through design examples of temporary bridges adapting the prestress-induced girder or the plate girder of the same section without prestresses. As a result, it has been found to be possible that the span length of HiPP girders for temporary bridges is longer than that of girders without prestresses.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.2
• /
• pp.137-144
• /
• 2009

This paper deals with the performance comparison of jammer signal's angle spreading in the beamforming after the estimation of direction of arrival using 3D array antenna basis of the GPS signal. After the estimation of direction of arrival using array antenna, the beamforming is need for the direction of arrival by spatial filtering and the other direction are nulling for reducing intererence signal, it is possible to improving the received signal strength and quality. But we obtains the degraded performance by the angle spreading due to the multi-jammer signal in this process. In this paper, the MUSIC and LCMV algorithms are applied for the estimating the direction of arrival and for beamforming using the 5 types of 3D array antenna. we performs the comparison of performance by calculating the bit error rate applying the BPSK modem and the varying the azimuth and elevation angle of incoming jammer signal. As a result of simulation, the Curved (B) type 3D array antenna has a more better performance compared to the other type antenna.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.1
• /
• pp.11-17
• /
• 2009

This paper deals with the estimation performance DoA (Direction of Arrival) using the 3D adaptive array antenna in W-CDMA signal. For this, we proposed the 5 types of 3D array antenna, and appied for the MUSIC in order to the estimation of DoA algorithm for that antenna, commonly, then the DoA estimation error was used for the estimation performance. In the mobile communication and radio positioning service, performing the spatial filtering after the DoA estimation in array antenna, the quality of receiving signal can improve by the nulling or minimization of interfering signal which is from the undesired direction and the forming of beam which is from the desired direction. The result of DoA estimation and the DoA estimation error by varying the signal to noise ration and the number of interfering signal and power of each type antenna was calculated by computer simulation. As a result of simulation, the other propose antenna has good performance excluding the stack 3D antenna in DoA estimation and the Curved-B type antenna has more superior performance when increasing the number of interfering signal and power in the DoA estimation error.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.3
• /
• pp.179-190
• /
• 2020

In this paper, we estimated the Direction of Arrival (DOA) using Conventional BeamForming (CBF), adaptive beamforming and compressive beamforming. Minimum Variance Distortionless Response (MVDR) and Multiple Signal Classification (MUSIC) are used as the adaptive beamforming, and grid-free compressive sensing is applied for the compressive sensing beamforming. Theoretical background and limitations of each technique are introduced, and the performance of each technique is compared through simulation and real experiments. The real experiments are conducted in the presence of reflected signal, transmitting a sound using two speakers and receiving acoustic data through a linear array consisting of eight microphones. Simulation and experimental results show that the adaptive beamforming and the grid-free compressive beamforming have a higher resolution than conventional beamforming when there are uncorrelated signals. On the other hand, the performance of the adaptive beamforming is degraded by the reflected signals whereas the grid-free compressive beamforming still improves the conventional beamforming resolution regardless of reflected signal presence.

• Smart Structures and Systems
• /
• v.18 no.6
• /
• pp.1189-1202
• /
• 2016

This paper describes an application of wavelet analysis for damage detection of a steel frame structure with bolted connections. The wavelet coefficients of the acceleration response for the healthy and loosened connection structure were calculated at each measurement point. The difference of the wavelet coefficients of the response of the healthy and loosened connection structure is selected as an indicator of the damage. At each node of structure the norm of the difference of the wavelet coefficients matrix is then calculated. The point for which the norm has the higher value is a candidate for location of the damage. The above procedure was experimentally verified on a laboratory-scale 2-meter-long steel frame. The structure consists of 11 steel beams forming a four-bay frame, which is subjected to impact loads using a modal hammer. The accelerations are measured at 20 different locations on the frame, including joints and beam elements. Two states of the structure are considered: healthy and damaged one. The damage is introduced by means of loosening two out of three bolts at one of the frame connections. Calculating the norm of the difference of the wavelet coefficients matrix at each node the higher value was found to be at the same location where the bolts were loosened. The presented experiment showed the effectiveness of the wavelet approach to damage detection of frame structures assembled using bolted connections.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.310-310
• /
• 2016

최근 NAND flash memory는 높은 집적성과 데이터의 비휘발성, 낮은 소비전력, 간단한 입, 출력 등의 장점들로 인해 핸드폰, MP3, USB 등의 휴대용 저장 장치 및 노트북 시장에서 많이 이용되어 왔다. 특히, 최근에는 smart watch, wearable device등과 같은 차세대 디스플레이 소자에 대한 관심이 증가함에 따라 유연하고 투명한 메모리 소자에 대한 연구가 다양하게 진행되고 있다. 대표적인 플래시 메모리 소자의 구조로 charge trapping type flash memory (CTF)가 있다. CTF 메모리 소자는 trap layer의 trap site를 이용하여 메모리 동작을 하는 소자이다. 하지만 작은 window의 크기, trap site의 열화로 인해 메모리 특성이 나빠지는 문제점 등이 있다. 따라서 최근, trap layer에 다양한 물질을 적용하여 CTF 소자의 문제점을 해결하고자 하는 연구들이 진행되고 있다. 특히, 산화물 반도체인 zinc oxide (ZnO)를 trap layer로 하는 CTF 메모리 소자가 최근 몇몇 보고 되었다. 산화물 반도체인 ZnO는 n-type 반도체이며, shallow와 deep trap site를 동시에 가지고 있는 독특한 물질이다. 이 특성으로 인해 메모리 소자의 programming 시에는 deep trap site에 charging이 일어나고, erasing 시에는 shallow trap site에 캐리어들이 쉽게 공급되면서 deep trap site에 갇혀있던 charge가 쉽게 de-trapped 된다는 장점을 가지고 있다. 따라서, 본 실험에서는 산화물 반도체인 ZnO를 trap layer로 하는 CTF 소자의 메모리 특성을 확인하기 위해 간단한 구조인 metal-oxide capacitor (MOSCAP)구조로 제작하여 메모리 특성을 평가하였다. 먼저, RCA cleaning 처리된 n-Si bulk 기판 위에 tunnel layer인 SiO2 5 nm를 rf sputter로 증착한 후 furnace 장비를 이용하여 forming gas annealing을 $450^{\circ}C$에서 실시하였다. 그 후 ZnO를 20 nm, SiO2를 30 nm rf sputter로 증착한 후, 상부전극을 E-beam evaporator 장비를 사용하여 Al 150 nm를 증착하였다. 제작된 소자의 신뢰성 및 내구성 평가를 위해 상온에서 retention과 endurance 측정을 진행하였다. 상온에서의 endurance 측정결과 1000 cycles에서 약 19.08%의 charge loss를 보였으며, Retention 측정결과, 10년 후 약 33.57%의 charge loss를 보여 좋은 메모리 특성을 가지는 것을 확인하였다. 본 실험 결과를 바탕으로, 차세대 메모리 시장에서 trap layer 물질로 산화물 반도체를 사용하는 CTF의 연구 및 계발, 활용가치가 높을 것으로 기대된다.