• 대한의용생체공학회:의공학회지
• /
• 제34권2호
• /
• pp.73-79
• /
• 2013

Purpose: The purposes of this study were to measure the dose distribution of Photodynamic therapy(PDT) laser with 635 nm wavelength using GafChromic film. Method & Result: We made each output 300 J by changing mW and sec using the laser beam radiation mode such as C.W(Continuous Wave) mode, Pulse mode and Burst Pulse mode and measured the does at 0 mm and 5 mm of distance from optic fiber catheter end to the film, and at 5 mm distance by changing the angle of the end of the optic fiber catheter as $0^{\circ}$ and $0.5^{\circ}$. The radiated film was scanned and OD(Optical Density) was compared. And two-dimensional isodose curves were obtained and the consistency of shapes was compared. It was confirmed that there was consistency between optic density and the dose radiated on the film when we radiated GafChromic film by changing distance and angle of 300 J output in each radiation mode coordinating mW and sec. Conclusion: In this study, we could identify the stability according to changes in laser beam modes, changes in output according to distance, changes in uniformity according to angle, and beam profiles using GafChromic film, and we could also get two-dimensional isodose curve. It was found that small change in the distance and angle that is made when optic fiber catheter was contacted on the treatment area did not make big effects on the output of beam and the uniformity of dose, and it was also found that GafChromic film could be utilized for the purpose of QA of PDT laser beam.

• Current Optics and Photonics
• /
• 제8권4호
• /
• pp.406-415
• /
• 2024

The major error factors that degrade the efficiency of coherent beam combining (CBC) are numerically studied in a comprehensive manner, paying particular attention to phase, tip-tilt, polarization angle, and beam quality. The power in the bucket (PIB), normalized to the zero-error PIB, is used as a figure of merit to quantify the effect of each error factor. To maintain a normalized PIB greater than or equal to 95% in a 3-channel CBC configuration, the errors in phase, tip-tilt, and polarization angle should be less than 1.06 radians, 1.25 ㎛, and 1.06 radians respectively, when each of the three parameters is calculated independently with the other two set to zero. In a worst-case scenario of the composite errors within the parameter range for the independent-95%-normalized-PIB condition, the aggregate effect would reduce the normalized PIB to 83.8%. It is noteworthy that the PIB performances of a CBC system, depending on phase and polarization-angle errors, share the same characteristic feature. A statistical approach for each error factor is also introduced, to assess a CBC system with an extended number of channels. The impact of the laser's beam-quality factor M² on the combining efficiency is also analyzed, based on a super-Gaussian beam. When M² increases from 1 to 1.3, the normalized PIB is reduced by 2.6%, 11.8%, 12.8%, and 13.2% for a single-channel configuration and 3-, 7-, and 19-channel CBC configurations respectively. This comprehensive numerical study is expected to pave the way for advances in the evaluation and design of multichannel CBC systems and other related applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.302-303
• /
• 2006

The response surface modeling of the pretilt angle control using ion-beam (IB) alignment on nitrogen doped diamond-like carbon (NDLC) thin film layer is investigated. The response surface model is used to analyze the variation of the pretilt angle under various process conditions IB exposure angle and IB exposure time are considered as Input factors. The analysis of variance technique is used to analyze the statistical significance, and effect plots are also investigated to examine the relationships betweenthe process parameters and the response. The model can allow us to reliably predict the pretilt angle with respect to the varying process conditions.

• 항공우주시스템공학회지
• /
• 제3권2호
• /
• pp.1-11
• /
• 2009

A structural modelling for study on dynamic characteristics of tapered composite aircraft wings in the form of thin-walled beam is presented. The proposed structural model includes effects of transverse shear flexibility exhibited by the advanced composite materials and warping restraint characterizing elastic anisotropy and induced structural couplings. The complex effects of these factors could have a role in more efficient analysis on those structural models.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.338-338
• /
• 2009

To date, rubbing has been widely used to align LC molecules uniformly. Although rubbing can be simple, it has fundamental problems such as the generation of defects by dust and static electricity, and difficulty in achieving a uniform LC alignment on a large substrate. Therefore, noncontact alignment has been investigated. Ion beam induced alignment method, which provides controllability, nonstop process, and high resolution display. We investigated the high pretilt angle effects on electro-optical properties of ion beam (IB)-irradiated liquid crystal cells. on a blended polymer surface. High pretilt angle of liquid crystals IB-irradiated on a blended polymer surface including such as 5% and 10% of homeotropic polymer contents can' be achieved. The threshold voltages of IB-irradiated twisted nematic (TN) cells on a blended polymer surface decrease with increasing the pretilt angle. Also, the rising time of IB-irradiated TN cells decreases with increasing the pretilt angle. However the decay time of IB-irradiated TN cells increases with increasing the pretilt angle. Consequently, the electro-optical properties of IB-irradiated TN cells depend strongly on the pretilt angle in a blended polymer surface.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• Transactions on Electrical and Electronic Materials
• /
• 제16권4호
• /
• pp.201-205
• /
• 2015

This paper dealt with the condensing technology of an LED light source that uses a parabolic reflector to replace a searchlight equipped with a xenon lamp. A ray-tracing simulation was conducted to analyze the influence of the diameter of the reflector and the size of the light source on light condensing. The combination of a parabolic reflector with a diameter of 620 mm and a focal distance of 220 mm, and a 9 mm multi-chip package (MCP) with a luminous flux of 7,000 lm showed the narrowest beam angle. The luminous intensity at the center was measured at 7.7×10⁶ cd. The distance between the light source and the point where the illuminance was 1 lx was calculated to be 2.8 km. The power consumption of the system was 95 W, which is only 9.5% of that of the 1 kW xenon searchlight, and the beam angle was 1.03°. In a site experiment, it was confirmed that the light ray reflected from the LED searchlight proceeds forward without any diffusion because of the narrow beam angle.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 The Korea-Japan Joint Symposium
• /
• pp.103-103
• /
• 2003

A newly developed contact angle measurement instrument by laser beam projection allows for rapid and direct determination of contact angles. From the result of comparative experiment and questionnaire, the laser contact angle.

• 자연과학논문집
• /
• 제12권1호
• /
• pp.49-59
• /
• 2002

펌프광과 조사광이 공간적으로 떨어져 있는 경우에 포화흡수 분광신호가 지수함수적으로 감소하는 이유를 설명하였다. 수파수 안정화에 이용되는 차동포화흡수 분광신호에서 최대의 신호광에 대한 이론적으로 계산한 결과 최적 각도는 세슘원자는 $1.33^{\circ}$이고, 루비듐$87^{\circ}$은 경우 $1.08^{\circ}$이었으며, 실험결과와 일치하였다.

• 한국인터넷방송통신학회논문지
• /
• 제24권1호
• /
• pp.23-30
• /
• 2024

본 논문에서는 광대역 특성을 가지는 능동위상배열 안테나의 설계, 검증 및 분석에 대하여 기술하였다. 능동위상 배열 안테나를 항공기 혹은 미사일에 적용하려면 배열 안테나의 소형화 및 광각 빔조향 특성을 확보하는 것은 피할 수 없는 안테나 설계 고려 사항이 될 수 있다. 특히 전자적으로 광각 빔조향 시 능동반사계수 특성은 시스템의 생존 및 성능 측면에서 최소화되어야 하는 설계 파라미터이다. 광대역 특성 및 광각 빔조향에 적합한 복사 소자로 본 논문에서는 Step Flared Notch(SFN)를 적용한 배열 구조를 설계하고 구좌표계 θ 각도 기준 최대 40° 빔조향에 따른 능동반사계수를 최소화하였다. 복사소자의 대역폭은 Ka대역에서 능동반사 기준으로 3GHz를 확인하였다. 또한 실제 제작된 8by8 배열 안테나는 근접전계 시험을 통해 복사소자의 단일 패턴을 측정하고, 수학적으로 합성하여 탐색기 시스템에 사용하는 송/수신빔을 예측하여 성능을 분석하였다.