• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.627-628
• /
• 2005

In recent years, the rapid growth of portable electronic device market requires higher density characteristics of batteries. The speed at which portability and mobility is advancing hinges much on the battery. What is important is this energy source that engineers design handled devices around the battery, rather than the other way around. Much improvement has been made in reducing the power consumption of portable devices. Currently, the most popular secondary battery is Li-ion battery. Li-ion has won the limelight and become the most prominent battery. This paper reviews the prospect and future of the Li-ion battery.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1054-1057
• /
• 1995

The pollution-free secondary Li ion battery has been developed recently. However due to short history of Li ion battery, the standards for characterized assessments and standardized testing methods have not been prepared and established yet. Also, the researches have not been done systematically regarding the operating methods of these new type of batteries. Such limited knowledge of new batteries emphasizes the importance of development of characterized assessment and the operating methods.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.378-379
• /
• 2006

The carbon thin film was developed by the CVD method using the carbon source of toluene with the stream of argon gas at $800{\sim}1100^{\circ}C$ for 1 hour. Developed carbon thin films have the material loading of 0.27 mg($800^{\circ}C$), 0.80 mg($900^{\circ}C$), 2.3 mg($1000^{\circ}C$), and 2.9 mg($1100^{\circ}C$) for the disk of 15 mm diameter on single side. The characteristics of carbon thin film as the anode of thin film battery were evaluated using Li|C coin cell. Li|C($1100^{\circ}C$) coin cell has the first specific discharge and charge capacity of 953 mAh/g and 374 mAh/g, respectively, resulting the first Ah efficiency of 39.3 %. Capacity retention of the 5th cycle was 93.2 % indicating good cycleability. The carbon thin film prepared by CVD shows good specific capacity and cycleability, but low Ah efficiency.

• Korean Chemical Engineering Research
• /
• 제56권6호
• /
• pp.779-783
• /
• 2018

본 연구에서는 차량용 12 V 납축전지로 주로 사용되는 VRLA (Valve regulated lead acid) 배터리의 충/방전 특성과 노화에 따른 이의 변화를 수학적으로 모델링하였다. 기존에 리튬 이온 배터리의 거동 예측에 주로 이용되어 왔던 수학적 모델링 기법을 상용 70 Ah VRLA 배터리에 적용하였다. 정전류 충/방전에 따른 전압의 변화를 모델링 결과와 비교하였다. 비교 결과로부터 사용된 수학적 모델이 납축전지에도 높은 정확도로 적용될 수 있음을 알 수 있었다. 또한 이를 이용하여 납축전지의 노화를 예측할 수 있음을 확인하였다.

• 융복합기술연구소 논문집
• /
• 제11권1호
• /
• pp.19-23
• /
• 2021

These days, sales of battery electric vehicles have been rapidly increasing due to the strict CO₂ regulations. However, since it take too long to measure the energy economy of electric vehicles, it has been required to improve the procedure of energy economy measurement. In order to improve this problem, the present study analyzed the battery charge/discharge pattern according to the changes in battery SOC (state of charge). In general, the energy economy test is started with a battery SOC charged to 100 %. However, it was identified that when the battery is fully charged, it can actually be charged over the 100 % (e.g., 100.5 %). This can induce errors in the energy economy measurement. Therefore, the present study recommend to start the test at SOC 99.9 %. The regenerative braking was partly restricted for the SOC over 90 %. This made it difficult to estimate the overall energy economy of the electric vehicle. However, it was identified that there was no change in the battery charge/discharge characteristics under the SOC 90 %. Therefore, the energy economy test can be shortened by predicting the overall energy economy through a short mileage test.

• 한국응용과학기술학회지
• /
• 제25권4호
• /
• pp.518-524
• /
• 2008

In this study, positive plates of lead acid battery of Pb-Ca alloy and Pb-Ca-Sn alloy were fabricated and the mechanical characteristics of positive plates were measured. This study observed how the changes of content of Ca & Sn affect interface corrosion which is located in between grid & active materials and lead acid batteries as well. The mechanical characteristics of grid alloy is better when Ca is 0.05 wt.% then 0.1 wt.%. This study said that the corrosion rate between the active material based on the charge/discharge cycle of lead acid battery and grid interface is much faster than a grid which contains Sn. And furthermore, according to the study the rate 30 of Sn/Ca which is added to grid shows the best performance.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.123-128
• /
• 2006

The proposed mathematical model of the starter-generator system incorporates the motor speed, battery voltage and the desired current to estimate the moment generation capabilities of the starter-generator and the actual current of the battery system. The fundamentals for this mathematical modeling are the simulated results of the experimental data. These pertinent data are used in establishing the governing equations for the determination of motor moments, actual battery currents and efficiencies of the system's operation at different loading characteristics and speed regions. The derived equations will be used into simulation programs to predict the fuel efficiency, vehicle characteristics of a hybrid electric vehicle equipped with a transmission starter-generator which will be developed.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.75-79
• /
• 2008

To control the lead storage batteries it is necessary to consider the characteristics of each battery connected in series. In this study, the charging and discharging characteristics of sealed lead storage batteries 12V/1.2A was investigated one by one through experiments. The results of the experiment shows that one should consider the state of each battery to prevent overcharge or deep discharge. Also, we designed an equipment to measure battery voltages simultaneously using micro-controller. This equipment will be useful for monitoring batteries at PV generation system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.292-292
• /
• 2010

Bimodal Tram is driven by both engine and Lithium Polymer battery pack which consists with 168 cells of LPB(80Ah, 650Vdc). LPB pack is very frequently charged and discharged in driving. Temperature inside of LPB pack makes an great effect on both charging and discharging capacity which seem to be related with LPB internal resistance. LPB internal resistance is increasing or little decreasing with the decreased temperature under 10 - $20^{\circ}C$ and the increased temperature over $30^{\circ}C$ which is similar to the temperature characteristics of single LPB cell. This paper has analyzed the driving characteristics of LPB pack for bimodal tram is running with either battery mode or hybrid mode.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.49-57
• /
• 2013

In this study, we fabricated a parallelly connected Li-ion battery/supercapacitor hybrid cell to combine the advantageous characteristics of Li-ion battery and supercapacitor, high energy density and high power density, respectively, and investigated its discharging characteristics over a wide temperature range from -40 to $25^{\circ}C$. At the initial state of discharging of the hybrid cell, the power was mostly provided by the supercapacitor and then the portion of the Li-ion battery was gradually increased. By installing a switching system into the hybrid cell, which controls the discharging sequence of Li-ion battery and supercapacitor, the maximum power was improved by 40% compared with non switching system. In addition at low temperatures, the power and discharging time of the hybrid cell were significantly enhanced compared to a battery-alone system. The hybrid cell is expected to be applied in electric vehicles and small domestic appliances that require high power at initial discharging state.