• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.10
• /
• pp.693-698
• /
• 2017

The 18650 battery cell is known to be reliable and cost effective, but it has a design limitation and low electric capacity compared to pouch-type cells. Because its economy is superior, an 18650-cell-type battery pack is chosen. A reliable temperature is very important in automobile battery packs. Therefore, in this study, the temperature stability of the battery pack is predicted using CFD simulation. Following 3C discharge tests, the results for the heat generation of the battery cell are compared to the simulation results. Based on these results, a natural convection condition, forced convection condition, direct cell-cooling condition, cooling condition on the upper and lower surfaces of the battery pack, and cooling condition using air channels are all simulated. The results indicate that the efficiency and the performance of the air-channel-type cooling system is good.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.597-598
• /
• 2005

Recently, the performance of portable electric equipment can often improved by a Li-ion battery assisted by a supercapacitor. A supercapacitor can provide high power density as well as a low resistance in the hybrid system. In this study, we have prepared, as the pluse power souce, a commercially supplied Li-ion battery with a capacity of 700mAh and AC resistivity of $60m\Omega$ at 1kHz and nonaqeous asymmetric hybrid capacitor composed of an activated carbon cathode and MCMB anode, and have examined the electrochemical characteristics of hybrid capacitor and the pulse performances of parallel connected battery/hybrid capacitor source. The nonaqueous asymmetric hybrid capacitor, the stacks of 10 pairs of the cathode, the porous separator and the anode electrode were housed in Al-laminated film cell. The hybrid capacitor, which was charged and discharged at a constant current at $0.25mA/cm^2$ between 3 and 4.3V, has exhibited the capacitance of 100F. And the equivalent series resistance was $32m\Omega$ at 1kHz. By combining a Li-ion battery and a hybrid capacitor, the pulse performance of battery can be improved 23% in run time under a pulse discharge of 7C-rate.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.1
• /
• pp.1-12
• /
• 2021

As increasing the international community's awareness of greenhouse gas reduction, the demand for eco-friendly ship fuel has accelerated recently. The fundamental aim of this study is to develop a new type of fully electrified ferry for passengers and cars considering Korean domestic coastal environmental conditions. Several technical difficulties are encountered in applying a fully electric propulsion system based on removable battery systems into a ship due to limitations imposed by the batteries' size and capacity. This paper reviews and analyzes marine environment regulations strengthened recently, technology trends related to fully electric propulsion vessels in each country, and Korean domestic coastal environments. We propose a new fully electrified car ferry design with a displacement of 400 t applied in Korea. It is powered by removable battery systems pre-charged in a safe inland charging station. The mobile battery system is developed to enable roll-on and roll-off using wheels. The characteristics of the ship motion are analyzed based on the weight and location of the battery systems. We expect our battery systems to be applicable to larger ships in the future.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.1
• /
• pp.85-94
• /
• 2011

Expanded graphites were used as anode materials of high power Li-ion secondary battery. The expanded graphite was prepared by mixing the graphite with $HClO_4$ as a intercalation agents and $KMnO_4$ as a oxidizing agents. The physical and electrochemical properties of prepared expanded graphites through the variation of process variables such as contents of intercalation agent and oxidizing agent, and heat treatment temperature were analyzed for determination of optimal conditions as the anode of high power Li-ion secondary battery. After examing the electrochemical properties of expanded graphites at the different preparing conditions, the optimal conditions of expanded graphite were selected as 8 wt.% of oxidizing agent, 400 g of intercalation agent for 20 g of natural graphite, and heat treatment at $1000^{\circ}C$. The sample showed the improved charge/discharge characteristics such as 432 mAh/g of initial reversible capacity, 88% of discharge rate capability at 10 C-rate, and 24 mAh/g of charge capacity at 10 C-rate. However, the expanded graphite had the problems of potential plateaus like natural graphite and lower initial efficiency than the natural graphite.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.239-244
• /
• 2009

This paper aims to report the effect of surface treatment on graphite and its effect on the improvement of $Al_2O_3$ and $nano-Li_4Ti_5O_{12}$. The structure and property of surface treatment on graphite were determined by scanning electron microscopy, transmission electron microscopy and electrochemical property and safety were determined by charge/discharge cycler, accelerating rate calorimeter. The composite with different metallic oxide exhibited the first efficiency of 82.5% and specific capacity of 350 mAh/g. Although the composite showed same efficiency and specific capacity at first cycle, surface treatment on graphite by $nano-Li_4Ti_5O_{12}$ exhibited a higher charge/discharge rate, cycle life and thermal stability.

• Journal of Korea Multimedia Society
• /
• v.19 no.7
• /
• pp.1179-1187
• /
• 2016

Through the rapid development of latest hardware technology, high performance as well as miniaturized size is the essentials of embedded system to meet various requirements from the society. It raises possibilities of genuine realization of IoT environment whose size and battery must be considered. However, the limitation of battery persistency and capacity restricts the long battery life time for guaranteeing real-time system. To maximize battery life time, low power technology which lowers the power consumption should be highly required. Previous researches mostly highlighted improving one single type of memory to increase ones efficiency. In this paper, reversely, considering multiple memories to optimize whole memory system is the following step for the efficient low power embedded system. Regarding to that fact, this paper suggests the study of volatile memory, whose capacity is relatively smaller but much low-powered, and non-volatile memory, which do not consume any standby power to keep data, to maximize the efficiency of the system. By executing function in specific memories, non-volatile and volatile memory, the quantitative analysis of power consumption is progressed. In spite of the opportunity cost of all of theses extra works to locate function in volatile memory, higher efficiencies of both power and energy are clearly identified compared to operating single non-volatile memory.

• Journal of the Korean Ceramic Society
• /
• v.39 no.4
• /
• pp.394-400
• /
• 2002

Tin oxide thin films doped with silicon as anodes for lithium secondary battery were fabricated by R. F. magnetron sputtering technique. The electrochemical results for lithium secondary battery anodes showed that addition of silicon decreases the oxidic state of tin, and, hence, reduced the irreversible capacity during the first discharge/charge cycle. The (110),(101),(211) planes were grown with increasing substrate temperatures. The reversible capacity of thin films fabricated in conditions of $300^{\circ}C$ substrate temperature and 7:3 $Ar:O_2$ ratio was 700 mAh/g.

• Korean Journal of Materials Research
• /
• v.33 no.6
• /
• pp.257-264
• /
• 2023

To develop a high capacity lithium secondary battery, a new approach to anode material synthesis is required, capable of producing an anode that exceeds the energy density limit of a carbon-based anode. This research synthesized carbon nano silicon composites as an anode material for a secondary battery using the RF thermal plasma method, which is an ecofriendly dry synthesis method. Prior to material synthesis, a silicon raw material was mixed at 10, 20, 30, 40, and 50 wt% based on the carbon raw material in a powder form, and the temperature change inside the reaction field depending on the applied plasma power was calculated. Information about the materials in the synthesized carbon nano silicon composites were confirmed through XRD analysis, showing carbon (86.7~52.6 %), silicon (7.2~36.2 %), and silicon carbide (6.1~11.2 %). Through FE-SEM analysis, it was confirmed that the silicon bonded to carbon was distributed at sizes of 100 nm or less. The bonding shape of the silicon nano particles bonded to carbon was observed through TEM analysis. The initial electrochemical charging/discharging test for the 40 wt% silicon mixture showed excellent electrical characteristics of 1,517 mAh/g (91.9 %) and an irreversible capacity of 133 mAh/g (8.1 %).

• Applied Chemistry for Engineering
• /
• v.35 no.3
• /
• pp.255-259
• /
• 2024

In this study, an aqueous-based redox flow battery (RFB) was constructed using tungstosilic acid (TSA), which is a kind of polyoxometalate, as the negative electrode active material and iron chloride (FeCl3) as the positive electrode active material in a sulfuric acid (H₂SO₄) supporting electrolyte. As a result of the cell's performance, it exhibited capacity fading and low energy efficiency. To address these issues, malic acid (MA), an organic additive, was introduced to the positive electrode active material and then tested for electrochemical properties and single cell performance. The malic acid in the iron chloride aqueous solution is working as a chelate agent, and two carboxyl groups are effectively coordinated with iron ions. It was found that MA reduced the electrolyte resistance of the positive electrode active material, leading to chemical stabilization and an increase in capacity and energy efficiency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.14-20
• /
• 2018

Electric vehicles are environmentally friendly because they emit no exhaust gas, unlike gasoline automobiles. However, since they are driven by the electric power from batteries, the distance they can travel based on a single charge depends on their energy density. Therefore, the lithium-ion battery having a high energy density is a good candidate for the batteries of electric vehicles. Since the electrode is an essential component that governs their efficiency, the electrode manufacturing process plays a vital role in the entire production process of lithium-ion batteries. In particular, the coating process is a critical step in the manufacturing of the electrode, which has a significant influence on its performance. In this paper, we propose an innovative process for improving the efficiency and productivity of the coating process in electrode manufacturing and describe the equipment design method and development results. Specifically, we propose a design procedure and development method in order to improve the core plate coating quality by 25%, using a technology capable of reducing the assembly margin due to its high output/high capacity and improving the product capacity quality and assembly process yield. Using this method, the battery life of the lithium-ion battery cell was improved. Compared with the existing coating process, the target loading level is maintained and dispersed to maintain the anode capacity (${\pm}0.4{\rightarrow}{\pm}0.3mg/cm^2r$ reduction).