• Membrane Journal
• /
• v.18 no.4
• /
• pp.317-324
• /
• 2008

Polysulfone membranes were prepared via the phase inversion process. With propionic acid as a nonsolvent additive, polysulfone casting solutions were solidified in an isopropanol bath. Propionic acid (PA) worked as a thermodynamic enhancer for phase separation and as a rheological suppressor for kinetic hindrance. Morphology of the prepared membranes significantly varied with propionic acid content in the casting solution. The dense skin layer, which was identified in the membrane prepared without PA, almost disappeared in the membrane prepared trom PA 10wt%. With 30wt% PA, the membrane revealed the morphological gradient from a nodular skin structure to a sponge-like substructure, including the finger-like cavity. Water permeability increased with PA content, and polyethylene glycol rejection decreased with the nonsolvent content.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.108-111
• /
• 2002

CIGS film has been fabricated on soda-lime glass, which is coated with Mo film. by multi-source evaporation process. The films has been prepared with thickness of 1.0 ${\mu}m$, 1.75${\mu}m$, 2.0${\mu}m$, 2.3${\mu}m$, and 3.0${\mu}m$. X-ray diffraction analysis with film thickness shows that CIGS films exhibit a strong (112) preferred orientation. Furthermore. CIGS films exhibited distinctly decreasing the full width of half-maximum and (112) preferred peak with film thickness. Also, The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the interplanar spacing were examined by X-ray diffraction. The preparation condition and the characteristics of the unit layers were as followings ; Mo back contact DC sputter, CIGS absorber layer : three-stage coevaporation, CdS buffer layer : chemical bath deposition, ZnO window layer : RF sputtering, $MgF_2$ antireflectance : E-gun evaporation

• The Journal of Korean Medicine
• /
• v.33 no.3
• /
• pp.160-183
• /
• 2012

Objectives: Coptidis Rhizoma is one of the most popular and multi-purpose herbs in traditional medicine. The purpose of this study was to contribute to research and applications of Coptidis Rhizoma in clinic, by analyzing and reviewing international studies on its chemical compositions and pharmacological effects. Methods: This study analyzed 344 articles published from 2000 to 2010 in PubMed, Refworks, Riss, and KTKP. The search keywords were "Coptis chinensis", "Coptis japonica", "Coptidis Rhizoma", "huanglian" and "huanglian in Chinese". From them, we selected 114 articles which met our inclusion criteria. Results: This study reviewed 114 articles on Coptidis Rhizoma and its active components in terms of 'Active components', 'Experimental studies', 'Clinical studies', 'Industrial use' and 'Side Effects/Toxicity'. Conclusions: The active components of Coptidis Rhizoma are berberine, coptisine, epiberberine, palmatine, jateorrhizine, magnoflorine, worenine, etc. It is reported that Coptidis Rhizoma and its active components have anti-inflammatory, antibacterial, antitumor, and antioxidant activity, and cardiovascular, hepatoprotective, antidiabetic, neuroprotective, gastrointestinal, pain relieving, discharge phlegm and metrocyte proliferation effects. Moreover, we found that Coptidis Rhizoma can be used for bath preparation, cosmetic products and as a natural antimicrobial substance.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.359-368
• /
• 2007

The copolymer membranes, poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) were prepared by phase inversion method using as an additive with N,N-dimethylformamid as a solvent. The pores are generated during the solvent and non-solvent exchange process in the coagulation bath filled with non-solvent (distilled water). The highest porosity of the membrane was 60%. The surface and cross-section of the membranes was observed with a scanning electron microscopy (SEM). The mechanical property of the membrane was determined by using an universal testing machine (UTM). Tensile strength of measured membranes is presented the maximum 6.57 MPa at 30 wt% of PVdF-HFP.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.6
• /
• pp.636-641
• /
• 2016

Alkaline water electrolysis is commercial hydrogen production technology. It is possible to operate MW scale plant. Because It used non-precious metal for electrode. But It has relatively low current density and low efficiency. In this study, research objective is development of anode for alkaline water electrolysis with low cost, high corrosion resistance and high efficiency. Stainless steel 316L (SUS 316L) was selected for a substrate of electrode. To improve corrosion resistance of substrate, Nickel (Ni) layer was electrodeposited on SUS 316L. Ni-Fe alloy was electrodeposited on the passivated Ni layer as active catalyst for oxygen evolution reaction(OER). We optimized preparation condition of Ni-Fe alloy electrodeposition by changing current density, electrodeposition time and composition ratio of Ni-Fe electrodeposition bath. This electrodes were electrochemically evaluated by using Linear sweep voltammetry (LSV) and Cyclic voltammetry (CV). The Ni-Fe alloy (Ni : Fe = 1 : 1) showed best activity of OER. The optimized electrode decreased overpotential about 40% at $100mA/cm^2$ compared with Ni anode.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.5
• /
• pp.193-198
• /
• 2015

In the study, electroless Ni-plating on flexible ethylene-propylene-diene-monomer (EPDM) rubber sheets for the application of an insert block for shielding electromagnetic interference of multi cable transit (MCT) systems was investigated. Ni crystallinity and adhesion have been found to vary with processing parameters such as pH and temperature of the plating bath. It was shown that Ni-films having the high crystallinity and optimum electric conductivity were obtained on EPDM rubber sheets under pH 7 and 8 at $60{\sim}70^{\circ}C$. The conductive Ni-plated EPDM rubber prepared at pH 7 at $70^{\circ}C$ showed the enhanced adhesion and electric conductivity, and the high electromagnetic interference shielding effect in the 400 MHz~1 GHz range.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.903-906
• /
• 2011

The electroplating and electro-less plating methods have been applied for the high density chip interconnect of the Copper Pillar Tin Bump (CPTB) preparation. The CPTB was prepared, which had been electroplated about $100{\mu}m$ pitch of copper layer firstly, and then the Tin layer was deposited on the copper pillar surface to protect the oxidation of it. It was also very important to get uniform thickness of electroplated copper layer, though it was difficult and sensitive. In order to control the thickness distribution, it was examined that the current separating disk of Insulating Gate with a hole in the center was installed between electrodes. The current flows through the center hole of the Insulating Gate in the cylindrical electroplating bath and the other parts were blocked to protect current flowing. The main current flowed through the center hole of the Insulating Gate directly to the opposite electrode of wafer disk. As the results, it was verified that the copper layer was thick in the center part of wafer disk with distribution of thinner to the outer part toward edge.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.342-349
• /
• 2000

Hollow fiber membranes were prepared via thermally-induced phase separation process followed by stretching process from isotactic polypropylene and soybean oil system. Various operating parameters were examined in terms of their effects on the structure variation and performances of the membrane, and were optimized. Melt viscosity of the melt sample had influence on the formation of the microfibrils, and addition of nucleating agent increased the nucleation density to enhance the interspherulitic pore formation by stretching. Annealing the membrane at its stretched state relaxed the stress induced by stretching and helped the membrane maintain the stretched structure without shrinking. Solid-liquid Phase separation is more prevalent when the nucleating agent was added, and coagulation bath temperature determined the nucleation density, which affected the pore formation by stretching. In the absence of nucleating agent, nucleation was not effective and liquid-liquid phase separation governed the structure formation, which showed the opposite trend to that of the case with nucleating agent.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.6
• /
• pp.689-695
• /
• 1999

Supercritical fluid extraction (SFE), ultrasonic extraction (USE), and accelerated solvent extraction (ASE) were compared with the well known Soxhlet extraction for the extraction of polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins(PCDDs) from the XAD-2 resin which was used to adsorb PCDDs in the atmosphere. XAD-2 resin spiked with five PCDDs was chosen as a sample. The optimum conditions for the extraction of PCDDs by SFE were turned out to be the use of CO2 modified with 10% toluene at 100 ℃ and 350 atm, with 5 min static extraction followed by 20 min dynamic extraction. SFE gave a good extraction rate with good reproducibility for PCDDs ranging from 68 to 98%. The ultrasonic extraction of PCDDs from XAD-2 was investigated and compared with other extractions. A probe type method was compared with a bath type. Two extraction solvents, toluene and acetone were compared with their mixture. The use of their mixture in probe type, with 9 minutes of extraction time, was found to be the optimum condition. The average recovery of the five PCDDs for USE was 82-93%. Accelerated solvent extraction (ASE) with a liquid solvent, a new technique for sample preparation, was performed under elevated temperatures and pressures. The effect of tem-perature on the efficiency of ASE was investigated. The extraction time for a 10 g sample was less than 15 min, when the organic solvent was n-hexaneacetone mixture (1 : 1, v/v). Using ASE, the average recoveries of five PCDDs ranged from 90 to 103%. SFE, USE, and ASE were faster and less laborious than Soxhlet extraction. The former three methods required less solvent than Soxhlet extraction. SFE required no concentration of the solvent extracts. SFE and ASE failed to perform simultaneous parallel extractions because of instrumental limitations.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.22-29
• /
• 2014

Recycling process of iron should be developed for efficient recovery of neodymium (Nd), rare metal, from acid-leaching solution of Nd magnet. In this study, $FeCl_3$ solution as iron source was used for preparation of iron nano particles with the condition of various factors, such as, reductant, and surfactant. $Na_4P_2O_7$ and Polyvinylpyrrolidone (PVP) as surfactants, $NaBH_4$ as reductant, and palladium chloride ($PdCl_2$) as a nucleation seed were used. Iron powder was analyzed by using XRD, SEM for measuring shape and size. Iron nano particles were prepared at the ratio of 1:5 (Fe (III) : $NaBH_4$). Size and shape of iron particles were round-form and 50 ~ 100 nm size. Zeta-potential of iron at the 100 mg/L of $Na_4P_2O_7$ was negative value, which was good for dispersion of metal particle. When $Na_4P_2O_7$ (100 mg/L), PVP($FeCl_3:PVP$ = 1 : 4, w/w) and Pd($FeCl_3:PdCl_2$ = 1 : 0.001, w/w) were used, iron nano particles which were round-shape, well-dispersed and near 100 nm-sized range. In this condition, $FeCl_3$ solution changed with spent Nd leachate solution, and then it is possible to be made round-formed iron nano particles at pH 9 and at the reaction bath over 20 L which is not include any surfactant.