• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.101-107
• /
• 1997

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties was decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the Ax atmospheric gas and the HNx atmospheric gas. As a result of several investigations. We confirmed the following characteristics ; mechanical properties was changed under the influence of the annealing cycle, the heat treatment method and the atmospheric gas. And, elongation in the HNx BAF was better than the Ax BAF. Finally, most important thing in the BAF is using proper annealing cycle in order to get a good quality.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.69-77
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties were decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the In atmospheric gas($H_2$ : 75%, $N_2$ : 25%) and the HNx atmospheric gas($H_2$ : 5%, $N_2$ : 95%) We confirmed the following characteristics, mechanical properties were changed under the influence of the annealing cycle and the atmospheric gas. And, we have some result according to heat treatment method. Elongation of the mechanical properties in the HNx BAF is higher than the Ax BAF. But tensile strength and hardness is higher than the HNx BAF.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1136-1139
• /
• 2009

Recently, various Ni doping systems and thermal annealing systems have been developed for fabrication of polycrystalline silicon film using SGS (super grain silicon) for medium and largesize AMOLED panels. In this study, we compare the potential of Ni doping systems including ALD (atomic layer deposition), AMD (atmospheric metal deposition), in-line sputter, and crystallization annealing systems including batch type furnace, inline furnace, and RTA (rapid thermal annealing) developed for the SGS method. Additional requirements for those systems to be used for mass production of large AMOLED TVs are suggested based on evaluation results for both poly-Si films and TFT backplanes.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2007년도 춘계학술발표회 초록집
• /
• pp.31-32
• /
• 2007

자동차 도장 전처리 공정 중 인산염처리는 소지와 도장층 사이의 밀착성을 향상시키고, 강판의 내식성을 향상시키는 목적으로 행하여진다. 인산염 조직이 치밀하게 형성되지 못하면 도장층 박리 등의 불량이 발생할 수 있다. 본 연구에서는 전기로재 BAF(Batch Annealing Furnace) 냉연강판의 인산염처리 특성에 대한 분석 및 개선안 도출 과정을 서술하였다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1227-1234
• /
• 1994

A cold spot temperature control system for the batch annealing furnace has been established in order to reduce energy consumption which is essential to improve productivity and stabilize the properties of products. A relationship between annealing cycle time and gas flow rate is developed and also for the variation of coil cold spot temperature with time during heating, and actual temperature measurements at mid-width of each coil during soaking. The results of the temperature variation effect on the cold rolled steel sheet batch annealing are as follows. (1) Cooling rate increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component change. (2) In case of short time heating, the slowest heating part is the center of B coil and in case of ling time heating, the low temperature point moves from the center of coil to inside coil. (3) The outside of top coil is the highest temperature point under heating, which becomes the lowest temperature point under cooling. (4) Soaking time determination depends on the input coil width, and soaking time for quality homogenization of 1214 mm width coil must be 2 hours longer than that of 914 mm width coil.