Stellite bearings for liquid Zn-/Al-Systems with advanced chemical and physical properties by Mechanical Alloying and Standard-PM-Route
-
- 한국분말야금학회:학술대회논문집
- /
- 한국분말야금학회 2000년도 춘계학술강연 및 발표대회 강연 및 발표논문 초록집
- /
- pp.9-10
- /
- 2000
An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.
기상청, 국토교통부 및 국방부는 각 기관의 특성에 맞게 기상, 수문 및 항공 관측용 레이더를 운영하고 있다. 2015년까지 국내에는 총 8대의 이중편파레이더(백령도, 용인테스트베드, 진도, 면봉산, 비슬산, 소백산, 모후산, 서대산 레이더)가 도입되어 운영되고 있다. 레이더를 운영 중인 세개 부처는 관측목적이 달라 레이더에 대한 운영방식, 자료 처리 방식 및 활용 방안 등에서 서로 많은 차이를 보여 왔으며 이러한 차이는 각 부처에서 운영하는 레이더 자료의 정확도가 달라지게 하는 원인이 되고 있다. 이에, 세 부처는 2010년 "기상-강우 레이더 자료 공동 활용에 관한 합의서"를 체결하고, 서로 다른 부처에서 생산된 모든 레이더 자료를 공동 활용하는 체계를 마련하였다. 범부처 이중편파레이더 자료의 합성을 위해서는 부처별 레이더 간의 정확도가 서로 유사해야한다. 서로간의 정확도가 다른 상태에서 레이더 강우 자료를 합성하게 된다면 공간적으로 품질이 다른 합성 강우장이 생산될 수밖에 없다. 이에 본 연구에서는 범부처 이중편파레이더 강우량의 정확도 향상과 통합을 위해 2015년도에 용인테스트베드 레이더에서 시행되었던 경험적 방법을 이용하였다. 그 결과 2015년 5월부터 10월까지의 백령도, 비슬산 및 소백산 레이더 자료에 대한 강우량 정확도(1-NE)가 70% 수준으로 향상되었다. 또한 레이더 편파변수 조절 전에는 정확도가 30~60%까지 넓은 범위를 보이고 있으나 조절 후 65~70%로 그 범위가 줄어들었다.
본 연구는 식품에 존재하는 Y. enterocolitica균의 신속한 검출방법을 조사하기 위하여 이균에 특이적인 특이적인 ail, yst 및 virF 유전자와 Yersinia 속균을 구별하는 subgenus-specific Y16S primer를 도입하여 multiplex PCR을 수행하였으며 Y. enterocolitica균의 검출 민감도와 특이도 및 먹는 샘물과 야채류에서의 적용실험을 각각 조사하였다. PCR 특이성 실험에서는 Y enterorolitica ATCC 27729균은 355 bp(ail), 134 bp(yst) 및 200 bp(Y16S) 3종의 유전자에 대한 DNA 증폭밴드를 나타내었으며, Y. enteroculitica ATCC 9610 및 ATCC 23715는 yst와 Y16S 2종에만 증폭을 보였다 반면에 기타 비병원성 Yersinia균인 Y. frederikseni, Y. intemedia, Y kri-steneni, Y pseudotuberculosis 등은 Y16S에만 DNA밴드를 나타내었으나 기타 세균인 E. colt ATCC 25392, Shi. dysen-teri, S. aureus ATCC 25923, L. monocytognes ATCC 19111 균에서는 어떤 primer에서도 특이 DNA 밴드를 확인할 수 없었다 PCR 민감도는 다른 유전자에 비하여 yst 유전자가 Y. enterocolitica균에 가장 높은 민감도를 나타내었고, Y16S 유전자는 속과 종에 관계없이 높은 민감도를 나타내었다. 따가서, 먹샘물이나 야채류에 대한 병원성 Yersinia균의 지표유전자자로서 속을 대표하는 Y16S유전자와 종을 대표하는 yst유전자를 선정하였다. 수질 중 Y. enferocolitica의 검출한계를 알아보기 위하여 일반세균수가 3600 CFU/mL정도 함유된 먹는 샘물의 경우, DNA를 분리하지 않고 단순 열처리한 배양액을 DNA주형으로 사용하여 multiplex-PCR을 실시한 결과, Y16S 와 yst 유전자 모두 7
Purpose: Lingual nerve (LN) damage may be caused by either tumor resection or injury such as wisdom tooth extraction, Although autologous nerve graft is sometimes used to repair the damaged nerve, it has the disadvantage of necessity of another operation for nerve harvesting. Moreover, the results of nerve grafting is not satisfactory. The nerve growth factor (NGF) is well-known to play a critical role in peripheral nerve regeneration and its local delivery to the injured nerve has been continuously tried to enhance nerve regeneration. However, its application has limitations like repeated administration due to short half life of 30 minutes and an in vivo delivery model must allow for direct and local delivery. The aim of this study was to construct a well-functioning
최근의 정보통신기술 발전에 기반한 무인 항공 전자탐사는 효율적인 광역 탐사가 가능하다는 장점으로 인해 다양한 활용이 시도되고 있다. 이 연구에서는 무인 항공 전자탐사의 실제 적용을 위한 이론 연구의 일환으로 한국지질자원연구원에서 개발된 무인 비행선 전자탐사 시스템에 대한 고찰을 수행하였다. 이 시스템은 기존의 항공 전자탐사 시스템들과는 다른 송수신루프의 배치로 인해 측정되는 자기장을 해석하기 위한 새로운 기술이 필요하다. 따라서, 임의의 모양을 갖는 송신원에 의한 전자기장 반응을 계산할 수 있는 방법을 제안하였으며 원형루프에 의한 이론해와의 비교 검증을 통해 그 타당성을 확인하였다. 또한, 3차원적으로 분포한 지하의 전도성 이상체에 의한 자기장 반응을 모사하기 위하여 변유한요소법 기반의 3차원 주파수영역 전자탐사 모델링 알고리듬과 결합하였다. 개발된 알고리듬을 바탕으로 지하 이상체에 의한 자기장 반응분석을 수행한 결과, 기존 항공 전자탐사 시스템들과 마찬가지로 탐사고도가 높아지거나 이상체의 심도가 깊어짐에 따라 이상체에 의한 반응이 줄어듦을 알 수 있었고 이상체의 전기비저항이 증가함에 따라서도 반응이 작아지는 것을 확인하였다. 그러나, 이상체의 심도 및 전기전도도와 사용 주파수에 따라 이상성분의 반응양상이 비선형적인 경향을 나타내는 구간이 존재하여, 자료해석 시 반응의 크기를 통한 단순 해석이 어려워지며 겉보기 비저항 계산 시에도 해의 비유일성을 야기시킬 수 있다는 것을 확인하였다. 따라서 실제로 시스템을 활용하여 탐사를 수행할 시, 탐사목적 및 현장 조건을 고려한 사전 모델링을 통해 적합한 주파수 대역 및 탐사고도를 설정하여 탐사를 수행하는 것이 선행되어야 한다.
고관절과 어깨의 점진적인 근육 약화를 특징으로 하는 지대형 근이영양증(limb-girdle muscular dystrophy: LGMD)은 우성 및 열성 유전을 모두 보여주며, TTN을 비롯한 많은 유전자가 발병과 관련된 것으로 알려져 있다. 본 연구는 40대 중반의 늦은 발병을 나타낸 상염색체 열성 LGMD 및 심방 조동의 증상을 가진 한 남성 환자의 유전적 원인을 규명하기 위해 수행되었다. 전장 엑솜 서열분석을 수행하여 환자로부터 TTN 유전자의 복합 이형 접합성 변이의 대립유전자를 동정하였다. 한 대립유전자는 [c.24124G>T (p.V8042F)]의 단일 변이를 보였지만, 다른 대립유전자는 [c.29222G>C (p.R9741P) + c.67490A>G (p.H22497R) + c.75376C>T (p.R25126C)]의 세 변이로 구성된 단상형이었다. 대립유전자 중 p.V8042F는 어머니로부터 유전된 반면, 다른 단상형 대립유전자는 아버지로부터 유전된 것으로 추정되었다. 본 연구에서 분리된 TTN 변이들은 공공 인간 유전체 데이터베이스(1,000 Genomes, gnomAD 및 KRGDB)에서 보고되지 않았거나 매우 낮은 빈도로 보고되었다. 대부분의 변이들은 고도로 보존된 면역글로불린 또는 피브로넥틴 도메인에 위치했으며, 일부 in silico 분석에 의해 병원성인 것으로 예측되었다. TTN 거대 단백질은 근육 조립, Z-라인에서 힘 전달, I-밴드에서 안정 장력 유지에 중요한 역할을 한다. 결론적으로, 우리는 이러한 이형접합성 복합 돌연변이의 이중 대립유전자가 LGMD 표현형의 유전적 원인으로서 작용할 수 있을 것으로 제시한다.
2017년 9월 3일 북한에서 발생한 인공지진 신호가 기상청 지진관측망에 관측되었다. 진앙은 풍계리 핵실험 지역으로 지금까지의 실험 중 가장 강력한 실험이었다. 직접적 접근이 제한되는 상황에서 6차 핵실험에 의한 주변 지표변화 연구를 위해 고해상도 위성 자료를 활용하였다. 우선, 지표변위 관측을 위해 ALOS-2 위성 자료를 활용하여 레이더 간섭기법(InSAR: SAR Interferometry)을 적용하였다. 하지만 6차 핵실험 주변 지역의 대규모 지표변위와 강한 진동으로 인해 낮은 긴밀도(coherence) 값을 지니며 레이더 간섭도가 생성되지 않았다. 이는 강한 진동으로 인한 표면의 변화와 레이더 간섭도가 생성 가능한 최대 지표변위 관측 범위보다 큰 변위가 발생했기 때문으로 추정되며 이러한 한계를 극복하기 위해 오프셋 트래킹(Offset Tracking) 방법을 활용하였다. 오프셋 트래킹 방법은 6차 핵실험 전 후 위성 영상레이더의 강도 영상(Intensity)에 대한 교차상관기법(Cross-Correlation)을 이용하는 것으로 상관관계 추정을 위해 사용된 윈도우 크기에 따라 결과가 달라지는 단점이 존재한다. 본 연구에서는 32부터 224까지 16단계로 윈도우 크기를 변화시키고 그 결과의 통계적 처리 후 지표변위를 생성하였다. 그 결과, 6차 핵실험 장소를 기준으로 만탑산 서쪽 지역에서 최대 3 m의 지표변위를 관측하였다. 또한, 고해상도 광학 영상을 활용하여 6차 핵실험에 의한 산사태 및 함몰지역으로 추정되는 지역을 확인하였다. 이러한 현상은 매우 강력한 지하 핵실험에 의한 것으로 판단되며 기존 음파 및 지진파를 이용한 핵실험 분석뿐만 아니라 고해상도 위성영상을 활용하여 비접근 지역에 대한 보조 분석 자료로 활용이 가능 할 것이다.
다산 등 15개의 통일형 벼 품종을 이용하여 mesotrione을 처리한 후 5일부터 다산 등 13개 품종들은 신엽에서 백화현상이 발생하였으나, 밀양154호와 수원382호는 백화현상이 발생하지 않아 저항성 품종으로 선발되었다. Mesotrione 처리 후 다산 등 13개 품종들의 초장 및 건물중 억제율은 밀양154호와 수원382호보다 더 높았으며 약량에 따른 억제율이 증가하였다. 한아름2호/밀양154호의
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70