• Journal of Aerospace System Engineering
• /
• v.4 no.3
• /
• pp.24-28
• /
• 2010

The purpose of this study is to define available microwave absorbing structure for aircraft from in the X-band(8.2~12.4GHz) frequencies. The electromagnetic wave absorption or shielding techniques is an important issue not only for military purpose but also for commercial purposes. Aircraft Radar Absorbing Structure(RAS) is absorbed or scattered propagation waves from the enemy radar. There are absorbing technologies at shaping design techniques and using Radar Absorbing Materials(RAM). RAM is more important because shaping design can't include perfect radar absorbing performance. In this study, based on material properties was introduced RAM and to analyze the each characteristics. Finally, we comparison appropriate RAM for aircraft.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.2
• /
• pp.164-168
• /
• 1995

The band structure of nickel monoxide having a cation defect rock salt structure is calculated by means of the tight-binding extended Huckel method. The calculation is also made for the net charge, the DOS, the COOP, the electron density of the constituent atoms, and the O 1s binding energy shift when one of the adjacent nickel atoms is defected. It is found that the band gap near the Γ direction on the Brillouin zone is about 0.2 eV, and that all of the properties calculated including the electronic structure of the oxygen atom are more effectively affected by the surface defect than the inside one. The core O 1s binding energy shift is calculated by the use of valence potential method and the results are very satisfactory in comparison with the XPS experimental findings.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.548-554
• /
• 1997

The single crystal of $Mg_{0.16}Zn_{0.84}$Te:Co(Co:0.01 mole%) was grown by vertical Bridgman method. The crystal structure of $Mg_{0.16}Zn$_{0.84}$Te:Co and optical absorption properties of this compound were studied. The grown single crystal has a cubic structure and a lattice constant a=6.1422 $\AA$ were determined by X-ray diffraction. As a result of the optical absorption spectra of $Mg_{0.16}Zn_{0.84}$Te:Co, the intracenter transitions due to $Co^{2+}$ ions were detected for $A-band:^4A_2(^4F){\to}^4T_2(^4F),\; B-band:^4A_2(^4F){\to}^4T_1(^4F), C- band:^4A_2(^4F){\to}^4T_1(^4P)$.The charge transfer transition near the absorption edge was observed in the wavelength range of 550 to 770 nm. According to the crystal field theory, the crystal field parameter(Dq) and the Racah parameter(B) were determined.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.75-79
• /
• 2015

In this paper, a dual band antenna with the operating frequency in HF and UHF band was proposed. The antenna structure consists of three spiral turns coil in the bottom side to generate the HF frequency of 13.56 MHz. In the top of the antenna, an inverted-spiral dipole structure is used to create the UHF frequency of 922 MHz. The dual band antenna was optimized to reduce size with $80mm{\times}40mm{\times}0.8mm$ dimension. The antenna presents the omnidirectional characteristic with high gain. To validate the theoretical design, the antenna was simulated using FR-4 substrate and verified the simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.288-297
• /
• 2007

The novel internal monopole chip antenna of penta-band operation for GSM850/GSM900/DCS/USPCS/WCDMA bands for mobile phones is proposed. This antenna occupies a small volume $8\times3.2\times20mm^3$ and is suitable to be embedded in a mobile phone as an internal antenna. The minimization of the proposed antenna was realized by using spiral line structure and meander line structure on FR-4 of dielectric$(\varepsilon_r=4.4)$. The designed antenna has the wide-band operation in the upper band by overlapping high order resonances. The measured bandwidth of this antenna (VSWR>3) is 150MHz$(1,030\sim1,180\;MHz)$ in the lower band operation and 650 MHz$(1,760\sim2,410\;MHz)$ in higher band operation. The measured radiation efficiency within bandwidth(VSWR 3:1) is over 50 %. The antenna has been designed by a commercial software HFSS.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1049-1056
• /
• 2017

In this paper, a microstrip-fed dual-band monopole antenna with two arc-shaped lines for WLAN(: Wireless Local Area Networks) applications was designed, fabricated and measured. The proposed antenna is based on a microstrip-fed structure, and composed of two arc-shaped lines and then designed in order to get dual band characteristics. We used the simulator, Ansoft's High Frequency Structure Simulator(: HFSS) and carried out simulation about parameters L2, L5, and with/without slit to get the optimized parameters. The proposed antenna is made of $13.0{\times}34.0{\times}1.0 mm^3$ and is fabricated on the permittivity 4.4 FR-4 substrate($12.0{\times}34.0{\times}1.0mm^3$). The experiment results are shown that the proposed antenna obtained the -10 dB impedance bandwidth 360 MHz (2.29~2.65 GHz) and 1,245 MHz (4.705~5.95 GHz) covering the WLAN bands. Also, the measured gain and radiation patterns characteristics of the proposed antenna are presented at required dual-band(2.4 GHz band/5.0 GHz band), respectively.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.405-410
• /
• 2023

This paper presents a novel method of implementing a dual-band antenna using a square patch with an inset feed structure. The proposed method is to simply design a dual-band antenna using an asymmetric inset structure with different lengths of slots dug into the patch for inset feeding. To verify the proposed method, a dual-band inset patch antenna supporting 1.57 GHz GPS and 2.4 GHz WiFi bands was designed and manufactured on a 1 mm thick FR4 substrate. From measurement, it was confirmed that the frequency bands of the antenna that satisfy a return loss of -10dB or less are 1.55~1.57GHz and 2.41~2.45GHz, which has dual-band characteristics. Using the proposed method, it is possible to simply implement a dual-band antenna using inset feeding, and it is expected to be utilized in a variety of application fields.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.267-274
• /
• 2018

$TiO_2/CuS$ nanocomposites were fabricated by precipitation of nanosized CuS via sonochemical method on electrospun $TiO_2$ nanofibers, and their structure, chemical bonding states, optical properties, and photocatalytic activity were investigated. In the $TiO_2/CuS$ nanocomposite, the position of the conduction band for CuS was at a more negative than that of TiO; meanwhile, the position of the valence band for CuS was more positive than those for TiO, indicating a heterojunction structure belonging to type-II band alignment. Photocatalytic activity, measured by decomposition of methylene blue under visible-light irradiation (${\lambda}$ > 400 nm) for the $TiO_2/CuS$ nanocomposite, showed a value of 85.94% at 653 nm, which represented an improvement of 52% compared to that for single $TiO_2$ nanofiber (44.97% at 653 nm). Consequently, the photocatalyst with $TiO_2/CuS$ nanocomposite had excellent photocatalytic activity for methylene blue under visible-light irradiation, which could be explained by the formation of a heterojunction structure and improvement of the surface reaction by increase in surface area.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.27-32
• /
• 2015

In this paper, a mushroom typed electromagnetic band gap (EBG) structure to be inserted in the printed circuit board (PCB) inner layer in order to stabilize the PCB power line is proposed for global-navigation satellite service (GNSS). In designing the proposed EBG structure, the target stop-bandwidth was designed from 1.55GHz to 1.81GHz including GNSS and mobile communication-related frequency bandwidth. In this bandwidth, the insertion loss(S21) was observed below about -40dB. From the simulation results, it is expected that the stabilization of power delivery network (PDN) structure in the PCB circuit design should be improved and the effective correspondence to EMI will be helpful.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.852-857
• /
• 2011

In this paper, the application of a variable characteristic impedance transmission line that can be used to design a dual-band bandpass filter(BPF) is presented. The proposed filter offers a fixed first frequency passband and a controllable second passband. The tuning of the second passband is achieved by varying the characteristic impedance of and open shunt stub line in a stub loaded resonator(SLR) with the help of a defected ground structure(DGS) transmission line and varactor diodes. In order to validate the proposed structure, a two stage dual-band BPF with three transmission zeros was implemeted and experimentally verified based on its theoretical predictions and simulations.