• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1414-1415
• /
• 2008

본 논문에서는 고출력 극초단파(High Power Microwave)가 쏘아지는 대상이 방어장비를 갖추고 있을 때 외부대상이 어떤 영향을 받는지를 규명하는데 목적이 있다. 입력펄스를 변조(modulation)시켜 저지대역(Stop Band) 주파수 대역에 맞추고, 펄스(Pulse)를 저대역 통과 필터의 저지대역에 통과시킨다. 이때 출력펄스의 응답(response)을 시간영역(Time-domain)에서 분석하여 정상상태(steady state)보다는 과도응답(Transient Response)을 확인하는 것을 제안한다. 이 방법은 저지대역의 파형이 필터를 통과해도 과도응답 때문에 필터가 제 역할을 하지 못한다는 이론을 규명한다. 이 이론은 고출력 극초단파가 외부대상에 미치는 영향에 있어서 전자파를 방어하려고 하여도 과도응답 상태 응답 때문에 타격을 받을 수 있다는 것을 규명한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.4
• /
• pp.399-404
• /
• 1987

By using the principles of the three line coupled, the equivalent admittance parameters of the band-stop filter of the three line two port spurline for MIC are derived. The frequency and in/output impedance characteristics of the filter were studied. One-section spurline bandstop filter with their stopband cented near 4GHz have been fabricated and tested. The results show good agreement between the theoretical centre frequency and the experimental results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.7
• /
• pp.1295-1297
• /
• 2008

Large-sized flat-panel displays are widely used for PC monitors and TV displays. In this paper, frequency domain pre-filter algorithms are presented for detection of defects in large-sized Thin Film Transistor-Liquid Crystal Display(TFT-LCD) panel surfaces. Frequency analysis with 1-D, 2-D FFT methods for extract the periodic patterns of lattice structures in TFT-LCD is performed. To remove this patterns, frequency domain band-stop filters were used for eliminating specific frequency components. In order to acquire only defected images, 2-D inverse FFT methods to inverse transform of frequency domain images were used.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1047-1048
• /
• 2006

The DITC of SRM for smooth hoist driving is presented in this paper. In the hoist system, the switched reluctance motor (SRM) is applied instead of induction motor because of high efficiency and good traction characteristic. In order to improve start-up and stop performance of hoist system, the smoothing operation sequence of SRM using DITC is proposed. According to the switching sequence and hysteric band, the instantaneous torque is controlled. Since, the proposed method uses only the turn-on angle depending on variation of load and speed, a simple DITC can be implemented. The validity is proved by simulation and experiment.

• Journal of Magnetics
• /
• v.11 no.3
• /
• pp.147-150
• /
• 2006

We have fabricated three-dimensional magnetophotonic crystals based on $\alpha$-$SiO_2$ opal films. Opal thin films grown on glass substrates were filled with bismuth substituted iron garnet (Bi:YIG). Scanning electron microscopy data, optical and magnetic properties of the synthesized samples confirm the presence of the Bi:YIG contentin the opal lattice. It is shown that the samples exhibit the (111) stop band, and transmissivity of the threedimensional magnetophotonic crystals is defined by both the film lattice and the Bi:YIG content.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1995-1997
• /
• 2007

In this paper we propose a wavelength-switchable fiber ring laser that employs a polarization-dependent fiber band stop filter. The fiber filter was fabricated by inscribing a long-period fiber grating on a high birefringent fiber. Dual-wavelength switching operation was accomplished by controlling the rotatable linear polarizer which rotated the polarization plane of the light circulating through the fiber laser cavity. The amplitude variation of both laser lines was measured to be less than 0.5 dB and the signal-to-amplified spontaneous emission ratio was more than 55 dB.

• Advances in aircraft and spacecraft science
• /
• v.1 no.4
• /
• pp.379-398
• /
• 2014

This article discusses the microvibration analysis of a cantilever configured reaction wheel assembly. Disturbances induced by the reaction wheel assembly were measured using a previously designed platform. Modelling strategies for the effect of damping are presented. Sine-sweep tests are performed and a method is developed to model harmonic excitations based on the corresponding test results. The often ignored broadband noise is modelled by removing spikes identified in the raw signal including a method of identifying spikes from energy variation and band-stop filter design. The validation of the reaction wheel disturbance model with full excitations (harmonics and broadband noise) is presented and flaws due to missing broadband noise in conventional reaction wheel assembly microvibration analysis are discussed.

• Journal of the Optical Society of Korea
• /
• v.14 no.3
• /
• pp.282-285
• /
• 2010

We printed a one-dimensional array of metallic wires and a two-dimensional array of metallic split ring resonators on a photo-paper by using a high-dots-per-inch resolution printer and an ink with silver nano-particles. The printed sample sizes are $1.0{\times}1.0cm^2$. The transmission measured by a terahertz time domain spectroscopy system shows that the arrays of wires and split ring resonators could act as polarizers and band-stop filters, respectively, in a terahertz frequency region.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.4
• /
• pp.706-713
• /
• 1997

In this paper, we propose a band stop filter(BSF) for reducing drag-like effect of the low pass filter(LPF), a block by block adaptive filtering method, and a motion adaptive filtering method, which show better results in terms of PSNR or human visual perception compared to the conventional method using LPF. The BSF improves the draglike effects of the low pass filter by passing temporal high frequency components of video sequences which correspond to objects with large motion. The proposed adaptive methods also improve the conventional adaptive filtering by modifying the conventional algorithm and applying the algorithms for small blocks. The simulation results show that the proposed filtering methods show better results in terms of PSNR and subjective tests in most cases. Also in case of block by block adaptive filtering, it is verified that the application of the algorithm for smaller block gives better results.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.5
• /
• pp.114-120
• /
• 1997

A design method is newly presented for the creation of planar type filters which shapes will be nonuniform transmission line with continuously varying characteristic impedances. Those filters yield frequency characteristics of the bandstop filter in transmission, and have not nay discontinuities. The design is achieved by the control of wave propagation in view to both reflection an transmission properties on the dispersive nonuniform line within the desired frequency band. The developed algorithm is based on optimized perturbations of inherent nulls of lobes from the solution of first-order nonlinear differential equation for reflection coefficients of the nonuniform line, and an appropriate distribution of reflection coefficient which affects to filter length and bandwidth. Practical measurements for designed wideband microstrip and stop filter show very good agreement with theoretical results.