• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.2
• /
• pp.109-116
• /
• 2022

In this paper, we propose a band rejection filter (BRF) with a state variable filter (SVF) structure to effectively remove the influence of 60 Hz line frequency noise introduced into the sensor system. The conventional BRF of the SVF structure uses an additional operational amplifier (OPAMP) to add a low pass filter (LPF) output and a high pass filter (HPF) output or an input signal and a band pass filter. Therefore, the notch frequency and the notch depth that determine the signal attenuation of the BRF greatly depend on the tolerance of the resistors used to obtain the sum or difference of the signals. On the other hand, in the proposed BRF, since the BRF output is formed naturally within the SVF structure, there is no need for a combination between each port. The notch frequency of the proposed BRF is 59.99 Hz, and it can be confirmed that it is not affected at all by the tolerance of the resistor through the Monte Carlo simulation results. The notch depth also has an average of -42.54dB and a standard deviation of 0.63dB, confirming that normal operation as a BRF is possible. Also, with the proposed BRF, noise filtering was applied to the electrocardiogram (ECG) signal that interfered with 60 Hz noise, and it was confirmed that the 60 Hz noise was appropriately suppressed.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.5
• /
• pp.194-198
• /
• 2003

A wide-band E-plane notch phased array antenna having bandwidths of 3:1 and a scan volume of $\pm$ 45 is designed considering the active element pattern (AEP) with analysis of the full structure of E-plane notch phased array antenna. Using the numerical E-plane waveguide simulator as an infinite linear array in the broadside angle, the active reflection coefficient (ARC) of the unit element is optimized in the design frequency range. To evaluate the convergence of the AEP, the simulation of full array as changing the number array is investigated, and the minimum numbers of array that have characteristics similar to the AEP of an infinite array are determined.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.320-327
• /
• 2012

In this paper, a novel ultra wide band(UWB) antenna with tri-band notch capability is proposed. The proposed antenna can reject WiMAX(3.3~3.7 GHz), WLAN IEEE 802.11a/n(5.15~5.825 GHz), and ITU(8.025~8.4 GHz) bands. Band rejection capability is achieved only split ring resonators(SRRs) and complementary SRRs(CSRRs). The SRR under the radiating patch, the CSRR loaded on the radiating patch, and the CSRRs on the ground of the CPW feeding reject the WiMAX, WLAN, and ITU bands, respectively. The simulation and measurement results demonstrate the performances of the proposed antenna.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.2
• /
• pp.463-469
• /
• 2016

In this paper, the use of a dual composite right/left-handed coplanar waveguide (CPW) transmission line is proposed for the design of a band rejection filter. The notch property of the filter is achieved by combining the convex signal line with the shorted concave meander line, and the equivalent circuit model is extracted from the geometry of the unit cell for organizing the band rejection property. Then the equivalent parameters of the unit cell are analyzed to identify those behaviors. And the dispersion characteristics and energy distributions are simulated. In the end, the band rejection filter is manufactured by cascading two proposed unit cells. We show that the measurement result for the resonant frequency demonstrates good agreement with the simulation result and the band rejection filter provides a rejection performance of 17.5 dB at the stopband frequency ranging from 869 MHz to 894 MHz.

• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.35-43
• /
• 2016

A compact ultra-wide band antenna with a quadruple band-notched characteristic is proposed. The proposed antenna consists of a slotted trapezoid patch radiator, an inverted U-shaped band stop filter, a pair of C-shaped band stop filters, and a rectangular ground plane. To realize the quadruple notch-band characteristic, a U-shaped slot, a complementary split ring resonator, an inverted U-shaped band stop filter, and two C-shaped band stop filters are utilized in this antenna. The antenna satisfies the -10 dB reflection coefficient bandwidth requirement in the frequency band of 2.88-12.67 GHz, with a band-rejection characteristic in the WiMAX (3.43-3.85 GHz), WLAN (5.26-6.01 GHz), X-band satellite communication (7.05-7.68 GHz), and ITU 8 GHz (8.08-8.87 GHz) signal bands. In addition, the proposed antenna has a compact volume of $30mm{\times}33.5mm{\times}0.8mm$ while maintaining omnidirectional patterns in the H-plane. The experimental and simulated results of the proposed antenna are shown to be in good agreement.

• Journal of Sensor Science and Technology
• /
• v.25 no.1
• /
• pp.8-12
• /
• 2016

A planar, light-weight, and low-cost notch filter structure is required for the KSTAR ECEI (Electron Cyclotron Emission Imaging) system to protect the mixer arrays from spurious plasma heating power. Without protection, this heating power can significantly degrade or damage the performance of the mixer array. To protect mixer arrays, a frequency selective surface (FSS) structure is the suitable choice as a notch filter to reject the spurious heating power. The FSS notch filter should be located between the lenses of the ECEI system. This paper presents a 170 GHz FSS notch filter for the KSTAR ECEI sensor application. The design of such an FSS notch filter is based on the single-sided square loop geometry, because that makes it relatively insensitive to the incident angle of incoming wave. The FSS notch filter exhibits high notch rejection with low pass-band insertion loss over a wide range of incident angles. This paper also reviews the simulated and measured results. The proposed FSS notch filter might be implemented in other millimeter-wave plasma devices.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.932-940
• /
• 2005

In this paper, a planar half-circle shape ultra-wideband(UWB) antenna fed by CPW is designed, fabricated and measured for UWB communications. Within the UWB band(3.1 GHz${\~}$10.6 GHz), 5.15 GHz${\~}$5.825 GHz frequency band is used by IEEE 802.1la WLAN applications. It may be necessary to notch out this band to avoid interference with IEEE 802.1la WLAN. Therefore, we have proposed three kinds of UWB antennas having a notch function, such as a rectangular slot, a hat-shaped slot a circle-shaped slot. The notch frequency of the proposed antenna can be adjusted by controlling the slot length or slot width. From the measured results, the proposed antennas show a good gain flatness except the IEEE 802.1la WLAN frequency band and have a reasonable agreement with simulated results.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.86-89
• /
• 1992

One of the most difficult problems in depth control for underwater vehicle is the effect of seaway disturbance. One component of the seaway forces is of large magnitude with a relatively narrow-band, first order component. The other component is generaly of somewhat smaller magnitude, second order component. Since the magnitude of the first order component is generally much greater than the compensating force that can be generating by the planes, it is undesirable for the controller to generate a control command. In this paper, we disigned adaptive notch filtering system using filter bank structure. Energies of each band-passed signal are obtained by MA(Moving Average) method and compared to produce center frequency. By adapting this parameter to notch filter, 1st order seaway disturbance can be removed, which lead to the improvement of automatic depth control system.

• Information and Communications Magazine
• /
• v.13 no.11
• /
• pp.181-191
• /
• 1996

In this paper we discuss narrow-band interference rejection schemes for spectrum overlay communications where direct sequence spread spectrum (DS/SS) communication system and narrow-band communication systems share the same frequency band. In this case, it is essential to reject the narrow-band signals to guarantee the performance of DS/SS system, while it is not necessarily required to reject the DS/SS signal to recover the narrow-band signal. We discuss several schemes such as time domain processing, frequency domain processing and exploiting the device characteristics to reduce the effect of narrow-band signal on DS/SS communication systems. Furthermore, we suggest a structure of tunable notch filter using gyrator that can easily be customized to ASIC.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.6
• /
• pp.1227-1232
• /
• 2011

Using the notch and isolation, we investigated the insertion loss and isolation characterics of the fabricated dielectric duplexers and bandpass filters for CDMA and W-CDMA dualband. Insertion loss(Tx band) and isolation(between Tx and Rx) of duplxer were about -2.1708dB and 45dB at CDMA band, respectively. Also, in the case of W-CDMA, the insertion loss(Tx band) and isolation(between Tx and Rx) showed about -2.6946 and 100dB, respectively. Summering the aboved results, fabricated the dielectric duplexers and bandpass filters will be contributed the increase of atttenuation and the decrease of interference at CDMA and W-CDMA dualband.