• 한국세라믹학회지
• /
• 제34권12호
• /
• pp.1268-1274
• /
• 1997

Effect of elastic/plastic mismatch on the fracture of Si3N4 coating in Si3N4/Si3N4 -BN bilayer was investigated by Hertzian indentation testing. A different amount of mismatch between two layers was induced by different BN addition in the substrate layer, and Hertizian cracks were induced by using WC ball indenter. As a result, as the elastic/plastic mismatch between coating and substrate layer increased, the coating fracture easily occurred. A bending stress induced by different elastic/plastic mismatch was main reason to cause the fracture of coating.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.378-385
• /
• 2000

Fracture resistance (J-R) curves, which are used for elastic-plastic fracture mechanics analyses, decreased under tension-compression loading condition. This phenomenon was proved by several former researches, but the causes have not been clear yet. The objective of this paper is to investigate the cause of this phenomenon. On the basis of fracture resistance curve test results, strain hardening hypothesis, stress redistribution hypothesis and crack opening hypothesis were built. In this study, hardness tests, Automated Ball Indentation(ABI) tests, theoretical stress field analyses, and crack opening analyses were performed to prove the hypotheses. From this study, strain-hardening of material, generation of tensile residual stress at crack tip, and crack opening effects are proved as the causes of the decrease hypothesis.

• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.130-136
• /
• 2005

The nondestructive evaluation system consisted of a ball indentation tester and a ultrasonic tester was developed to evaluate material properties. The relations between the parameters from test results using the system and the results of tensile and fracture toughness tests were investigated. The fracture toughness and tensile properties could be determined using the system. Some metallic materials were experimented to predict the fracture toughness and tensile properties and verify the relations between them. The predicted fracture toughness and tensile properties show a good agreement with the results obtained by conventional tests. It is found that the material properties and the material degradation can be evaluated using the nondestructive evaluation system.

• International Journal of Safety
• /
• 제1권1호
• /
• pp.7-12
• /
• 2002

This paper demonstrates the impact stresses and wave propagation characteristics of glass/epoxy laminates subjected to the low-velocity impact by a steel ball theoretically and experimentally. A plate finite element model in conjunction with experimental contact laws is used for the theoretical investigation. The specimens for statical indentation and impact test are composed of $[0/45/0/-45/0]_28 and [90/45/90/-45/90]_28$ stacking sequences and have clamped-simply supported boundary conditions. Finally, these two results are compared and then the impulsive stress and wave propagation characteristics of this laminated composite are studied.

• 대한금속재료학회지
• /
• 제47권1호
• /
• pp.50-58
• /
• 2009

In this study, alumina matrix composites reinforced with carbon nanotubes (CNTs) were fabricated by ultrasonic dispersion, ball milling, mixing, compaction, and sintering processes, and their relative density, electrical resistance, hardness, flexure strength, and fracture toughness were evaluated. 0~3 vol.% of CNTs were relatively homogeneously dispersed in the composites in spite of the existence of some pores. The three-point bending test results indicated that the flexure strength increased with increasing volume fraction of CNTs, and reached the maximum when the CNT fraction was 1.5 vol.%. The fracture toughness increased as the CNT fraction increased, and the fracture toughness of the composite containing 3 vol.% of CNTs was higher by 40% than that of the monolithic alumina. According to observation of the crack propagation path after the indentation fracture test, a new toughening mechanism of grain interface bridging-induced CNT bridging was suggested to explain the improvement of fracture toughness in the alumina matrix composites reinforced with CNTs.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권8호
• /
• pp.348-353
• /
• 2003

This paper was the research of high voltage suspension insulator (400 [kN]) including pottery stone, feldspar, clay and alumina of 17 [wt%]. The slurry was fabricated after ball milling mixed raw materials. Green compacts were made by the extrusion of jiggering method and were sintered at 1300[$^{\circ}C$] for 50 [min.] in the tunnel kiln. The sintered density was reached to 97% of theoretical density, and the bending strength was 1658 [k $g_{f}$/$\textrm{cm}^2$] and hardness and fracture toughness which was measured by ICL( indentation crack length ) method were 1658 (kgf/$\textrm{cm}^2$) and 27.5 [Gpa], respectively. In measurement of tana and insulation break voltage of 400 (kN) porcelain, tan$\delta$ took some numerical value between 17${\times}$10$_{-3}$ and 61${\times}$10$_{-3}$ and insulation break voltage value was 19.9$\pm$1.4 [㎸/mm]. The test was performed to research whether the shape of pin affect a overvoltage break load or not As a consequence, when a pin was designed a pin diameter 51 [mm] with the bottom form of two-step constructed with straight in the suspension insulator, Insulator showed overvoltage break load 52 [ton] of the highest value and reflected a fine characteristic in aged deterioration test which is one of the accelerated aging test. Also it could be confirmed a fine characteristic through performing the test that electrical property of insulator was established correctly in accordance with IEC 60383-1 standards.s.

• 한국안전학회지
• /
• 제7권1호
• /
• pp.39-45
• /
• 1992

강구에 의한 횡방향 저속 충격을 받게 되는 복합재의 충격 응력 및 파동 전파에 관한 이론적 및 실험적 연구가 행하여 진다. 이론적 해석을 위해서는 실험적 접촉 법칙과 연계된 Whitney와 Pagano의 이론에 근거한 판 유한 요소 모델이 사용되며, 실험적 해석을 위해서는 직접적인 충격실험이 수행된다. 이러한 해석을 위한 시험편은 ［0/45/0/­45/0］$_{2s}$와 (90/45/90/­45/90)$_{2s}$ 적층 순서를 가지는 유리/에폭시 적층 복합재이며 경계 조건은 clamped-simply support이다. 결과적으로 이러한 두 해석 결과들이 비교 검토되며, 적층 복합재의 충격 응력 및 파동 전파 특성이 규명된다.명된다.

• 한국표면공학회지
• /
• 제54권6호
• /
• pp.357-364
• /
• 2021

In this study, DLC films deposited by PECVD were evaluated to the properties of super-hydrophobic by CF₄ treatment. The structure of DLC films were confirmed by Raman Spectra whether or not mixed sp³ (like diamond) peak and sp² (like graphite) peak. And the hydrogen contents in the DLC films (F-DLC) were measured by RBS analysis. In addition, DLC films were analyzed by scratch test for adhesion, nano-indentation for hardness and tribo-meter of Ball-on-disc type for friction coefficient. In the result of analysis, DLC films had traditional structure regardless of variation of hardness at constant conditions. Also adhesion of DLC film was increased as higher material hardness. Otherwise, friction coefficient was increased as lower material hardness. The DLC films were treated by CF₄ plasma treatment to enhance the properties of super-hydrophobic. And the DLC films were measured by ESEM(Enviromental Scanning Electron Microscope) for water condensation.

• Composites Research
• /
• 제31권5호
• /
• pp.260-266
• /
• 2018

본 논문에서는 C/C-SiC 복합재료의 하프늄 탄화물 코팅재에 대한 열적, 기계적 특성을 평가하였으며 특히 코팅에 의한 내산화성과 내마모성의 향상여부를 평가하였다. 하프늄 탄화물(HfC)을 용사시켜 코팅한 샘플들을 가공한 후, 공기 중에서 열적 특성평가 및 마모, 압입시험 평가에 대한 연구를 수행하였다. 공기 중에서 $1200^{\circ}C$의 온도까지 승온시킨 후 1시간 유지하는 싸이클을 10싸이클 진행하여 각 싸이클마다의 무게변화를 통해 탄소의 산화저항성을 평가하였고, 초경 구(tungsten carbide)를 사용하여 마모시험과 압입시험을 수행하여 그 결과를 비교하였다. 열피로 시험 수행 결과 하프늄 탄화물 코팅재가 상대적으로 무게감소가 적어 상대적으로 내산화성이 높은 것으로 평가되었다. 코팅된 하프늄 탄화물에 의해 탄성계수가 상대적으로 증가하였으며, 또한 C/C-SiC 복합재료는 하프늄 탄화물의 코팅에 의하여 내마모성이 향상되어 동일조건에서 마모량이 상대적으로 적었고 낮고 안정된 마찰계수가 유지되었다.

• 구강회복응용과학지
• /
• 제17권3호
• /
• pp.199-204
• /
• 2001

This study was to investigate the reused possibility of zirconia reinforced glass-ceramic(IPS Empress Cosmo ceramic) with sprue button in the flexure strength and fracture toughness. 40 disk-shaped ceramic specimens (20 specimens: as-pressed material; 20 specimens: reused material) with approximately 1.7 mm thickness and 15 mm diameter were prepared by "lost wax" technique. The remnants(sprue buttons) were used for repressing. The surface treatments for the discs were gradually abraded with 320, 800, 1200, and 2000 grit SiC sandpaper. The specimens were evaluated their flexure strength with the biaxial flexure jig(ball-on-three balls) and their fracture toughness with Vickers Indentation-microfracture test. The Weibull moduli were calculated for biaxial flexural strength. The mean flexure strength and fracture toughness of each group were $122.2{\pm}18.3MPa$, $1.00{\pm}0.09MPa{\cdot}m^{0.5}$ (as-pressed ceramics), and $122.2{\pm}20.3MPa$, $1.01{\pm}0.10MPa{\cdot}m^{0.5}$ (reused ceramics). There were no significant differences in the strength and the fracture toughness between the as-pressed and the reused IPS Empress Cosmo ceramic (P>0.05). This implied zirconia reinforced glass-ceramic(IPS Empress Cosmo ceramic) could be used one more time by reusing of sprue button in the flexure strength and fracture toughness.