• 한국공작기계학회논문집
• /
• 제16권3호
• /
• pp.81-87
• /
• 2007

It is important to investigate the relationship between weld process parameters and weld bead geometry for adaptive arc robot welding. However, it is difficult to predict an exact back-bead owing to gap in process of butt welding. In this paper, the quantitative prediction system to specify the relationship external weld conditions and weld bead geometry was developed to get suitable back-bead in butt welding which is widely applied on industrial field. Multiple regression analysis and artificial neural network were used as the research methods. And, the results of two prediction methods were compared and analyzed.

• 한국공작기계학회논문집
• /
• 제16권5호
• /
• pp.84-89
• /
• 2007

This research was done on the basis of assumption that there is a relationship between welding parameters and geometry of the back-bead being a gap in arc welding. Multiple regression analysis was used as method for predicting the geometry of the back-bead. The analysis data and the verification data were used for the formation of multiple regression analysis. The method was used to perform the prediction of the back-bead.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.79-86
• /
• 2007

The shape of excessive penetration mainly depends on welding conditions(welding current and welding voltage), and welding process(groove gap and welding speed). These conditions are the major affecting factors to width and height of back bead. In this paper, back-bead prediction and weldability estimation using artificial neural network were investigated. Results are as follows. 1) If groove gap, welding current, welding voltage and welding speed will be previously determined as a welding condition, width and height of back bead can be predicted by artificial neural network system without experimental measurement. 2) From the result applied to three weld quality levels(ISO 5817), both experimented measurement using vision sensor and predicted mean values by artificial neural network showed good agreement. 3) The width and height of back bead are proportional to groove gap, welding current and welding voltage, but welding speed. is not.

• 한국생산제조학회지
• /
• 제20권1호
• /
• pp.74-80
• /
• 2011

In this study, a variety of welding experiments were carried out to optimize root-pass welding process using GMA process. Based on the experimental results, optimal welding conditions were selected after analyzing correlation between welding parameters and back-bead geometry. Then, effectiveness of empirical models developed was compared and analyzed, and optimized empirical models were finally developed for predicting back-bead by analyzing the main effect of each factor which affects back-bead geometry and their influence on interaction. Also, functions proper for expressing the surface of back-bead were selected using diverse quadratic functions, and back-bead geometry was visualized using empirical models developed and quadratic functions.

• 한국산학기술학회논문지
• /
• 제9권4호
• /
• pp.871-877
• /
• 2008

Adaptive 아크 로봇 용접을 위한 용접 공정 변수와 용접 부 형상 사이에 상관관계를 조사하는 것은 중요한 일이다. 하지만 맞대기 용접의 공정에 있어 갭으로 인해 정확한 이면비드를 예측하는 것은 어려운 일이다. 본 연구에서는, 먼저 맞대기 용접을 통해 외부 용접 조건과 용접 비드 형상사이 상관관계가 규명되었고, 이를 응용하여 적절한 이면비드를 얻기 위한 개발이 이루어졌고, 이 연구결과는 산업 전 분야에 폭넓게 사용될 수도 있다. 다중회귀분석법이 공정변수 예측을 위한 연구방법으로 적용되었다. 예측방법의 결과들 또한 비교 및 분석이 이루어졌다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.206.1-206.1
• /
• 2005

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.203-206
• /
• 1999

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.208-213
• /
• 2001

Objective of this paper is to develop a new approach involving the use of an Artificial Neural Network(ANN) and multiple regression methods in the prediction of process parameters on bead height for GMA welding process. Using a series of robotic are welding, multi-pass butt welds carried out in order to verify the performance of the neural network estimator and multiple regression methods. To verify the developed system, the design parameters of the neural network estimator are selected from an estimation error analysis. The experimental results show that the proposed models can predict the bead height with reasonable accuracy and guarantee the uniform weld quality.