• Geomechanics and Engineering
• /
• v.34 no.4
• /
• pp.397-408
• /
• 2023

Pipe pile walls are commonly used as retaining structures for excavation projects, particularly in densely populated coastal cities such as Hong Kong. Pipe pile walls are preferred in reclaimed land due to their cost-effectiveness and convenience for installation. However, the pre-bored piling techniques used to install pipe piles can cause significant ground disturbance, posing risks to nearby sensitive structures. This study reports a well-documented case history in a reclamation site, and it was found that pipe piling could induce ground settlement of up to 100 mm. Statutory design submissions in Hong Kong typically specify a ground settlement alarm level of 10 mm, which is significantly lower than the actual settlement observed in this study. In addition, lateral soil movement of approximately 70 mm was detected in the marine deposit. The lateral soil displacement in the marine deposit was found to be up to 3.4 and 3.1 times that of sand fill and CDG, respectively, mainly due to the relatively low stiffness of the marine deposit. Based on the monitoring data and site-investigation data, a 3D numerical analysis was established to back-analyze soil movements due to the installation of the pipe pile wall. The comparison between measured and computed results indicates that the equivalent ground loss ratio is 20%, 40%, and 20% for the fill, marine deposit and CDG, respectively. The maximum ground settlement increases with an increase in the ground loss ratio of the marine deposit, whereas the associated influence radius remains stationary at 1.2 times the pipe pile wall depth (H). The maximum ground settlement increases rapidly when the thickness of marine deposit is less than 0.32H, particularly for the ground loss ratio of larger than 40%. This study provides new insights into the pipe piling construction in reclamation sites.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.70-75
• /
• 2000

The recycled single crystal silicon wafers have been fabricated into solar cells. It can be a solution for the high cost in materials for solar cells and recycling of materials. So, p-type (100) single crystal silicon wafers with high resistivity of $10-14\;{\Omega}cm$ and the thickness of $650\;{\mu}m$ were used for the fabrication of solar cells. Optimistic conditions of formation of back surface field, surface texturing and anti-reflection coating were studied for getting high efficiency. In addition, thickness variation of solar cell was also studied for increase of efficiency. As a result, the solar cell with efficiency of 10% with a curve fill factor of 0.53 was fabricated with the wafers which have the area of $4\;cm^2$ and thickness of $300\;{\mu}m$. According to above results, recycling possibility of wasted wafers to single crystal silicon solar cells was confirmed.

• Journal of Korean Medicine Rehabilitation
• /
• v.27 no.4
• /
• pp.97-109
• /
• 2017

Objectives The aim of this study is to analyze the patients who have low back pain through registry. Methods We registered patients with low back pain who visited department of korean rehabilitation medicine in university hospitals on study. We collected data from 116 subjects consisted of 51 inpatients and 65 outpatients and ruled out 8 who didn't have pattern identification data at the point of inpatient or outpatient visit so we analyzed 108 in total. We used Pearson's product moment correlation to find correlationship among variables, and analyzed statistical data using Phyton scipy library stats package. Results We set general features, region of the pain, physical examination, ROM, questionnaire results, pattern identification as variables and draw a conclusion by analyzing these variables. Conclusions Registry aimed at low back pain patients was established in department of korean rehabilitation medicine of university hospitals and exploratory analysis based on data were made. Through the registry, we expect that more advanced studies will be performed; for example, executing research which verifies effectiveness and stability of korean medical treatment or developing tools to fill the gap between pattern identification and disease identification.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.1
• /
• pp.55-64
• /
• 1992

This study investigated the effect of porcelain primer on bonding of coomposite resin to porcelain surface. In order to test the bond strength between porcelain and composite resin, porcelain cylinders were embedded in acrylic resin, and polished with 240grit silicone caqrbide paper. The specimens were divided into twelve groups. All specimens were treated with three porcelain primers and bonded with five composite resins. All test groups were stored in $37^{\circ}C$ distilled water for 48hours. Shear bond strengths were measured with Instron(Model 4201) at a cross-head speed of 1mm/min. The obtained results were as follows : 1. Scotchprime/Silux II group and BISCO Porcelain Primer/Bisfill group showed significant higher bond strengths than Clearfil Porcelain Primer/photo Clearfil Bright group(p<0.05). And there was no significant differences in bond strengths between Scotchprime/Silux II group and BISCO Porcelain Primer/Bisfill group(p>0.05). 2. When composite resins were used with Scotchprime, the bond strengths were decresed Silux II$(16.68{\pm}3.35MPa)$, Bisfil$(16.23{\pm}4.54MPa)$, Poly-Fill$(14.74{\pm}4.08MPa)$, Photo Clearfil Bright$(13.75{\pm}2.89MPa)$ and Pekalux$(14.74{\pm}4.08MPa)$ in order, but there was no statistical significance(p>0.05). 3. When composite resins were used with BISCO Porcelain Primer, the bond strength were decreased Bisfil$(16.17{\pm}1.60MPa)$, Silux II$(12.13{\pm}2.37MPa)$, Poly-Fill$(10.78{\pm}1.99MPa)$, Photo Cleafil Bright $(9.91{\pm}4.59MPa)$ and Pekalux$(7.36{\pm}2.16MPa)$ in order, but there was no statistical significance(p>0.05). 4. Silux II, Photo Clearfil Bright and Poly-Fill used with Scotchprime showed significant higher bond strengths than BISCO Porcelain Primer(p>0.05).

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.91.1-91.1
• /
• 2010

There are some methods for increasing efficiency of crystalline silicon solar cells. Among them, It is important to reduce the recombination loss of surface for high efficiency. In order to reduce recombination loss is a way to use the BSF(Back Surface Field). The BSF on the back of the p-type wafer forms a p+layer. so, it is prevented to act electrons of the p-area for the rear recombination. As a result, the leakage current is reduced and the rear-contact has a good Ohmic contact. therefore, open-circuit-voltage and Fill factor(FF) of solar cells are increased. This paper investigates the formation of rear contact process comparing Aluminum-paste(Al-paste) with Aluminum-Metal(99.9%). It is shown that the Aluminum-Metal provides high conductivity and low contact resistance of $21.35m{\Omega}cm$ using the Vacuum evaporation process but, it is difficult to apply the standard industrial process because high Vacuum is needed and it costs a tremendous amount more than Al-paste. On the other hand, using the Al-paste process by screen printing is simple for formation of metal contact and it is possible to produce the standard industrial process. however, it is lower than Aluminum-Metal(99.9) of conductivity because of including mass glass frit. In this study, contact resistances were measured by 4-point prove. each of contact resistances is $21.35m{\Omega}cm$ of Aluminum-Metal and $0.69m{\Omega}cm$ of Al-paste. and then rear contact have been analyzed by Scanning Electron Microscopy(SEM).

• Tunnel and Underground Space
• /
• v.11 no.2
• /
• pp.174-181
• /
• 2001

The cavities created by underground mining, if remained unfilled, can cause ground settlement and surface subsidence as a result of relaxation and breakdown of the carven roof. Construction of structures above the underground mine cavity will have serious problems concerning both structural stability and safely even if the cavity is back-filled. This study was conducted to confirm the location and condition of the cavern as well as the state of the back-fill in A mine area using core logging and borehole camera. The bearing capacity and other mechanical properties of the ground were also measured by the standard penetration test(SPT). Obtained data were used to assess the stability of the ground and the structures to be built by numerical analysis using FLAC. The site investigation results showed that the mine cavities were filled with materials such as boulder and silty sand(SM by unified classification). Result of the numerical analyses indicated that constructing building structures on the over-lying ground above the filled cavities is secure against the potential problems such as surface subsidence and ground settlement.

• Journal of Pharmacopuncture
• /
• v.6 no.1
• /
• pp.35-36
• /
• 2003

Background: Evidence based medicine has become main tools for medical practice. However, conducting a highly ranked in the evidence hierarchy pyramid is not easy or feasible at all times and places. There remains a room for descriptive clinical outcome measure studies with admitting the limit of the intepretation. Aims: Presents three Korean clinic based outcome measure studies with a view to encouraging Korean clinicians to conduct similar studies. Methods: Three studies are presented briefly here in치uding 1) Quality of Life of liver cancer patients after 8 Constitutional acupuncture; 2) Developing a Korean version of Measuring yourself Medical Outcome profile (MYMOP); and 3) Survey on 5 Shu points: a pilot In the first study, we have included 4 primary or secondary liver cancer patients collecting their diagnostic X-ray film and clinical data f개m their hospital, and asked them to fill in the European Organization Research and Treatment of Cancer, Quality of Life Questionnaire before the commencement of the treatment. The acupuncture treatment is set up format but not disclosed yet. The translation and developing a Korean version of outcome measures that is Korean clinician friendly has been sought for MYMOP is one of the most appropriate one. The permission was granted, the translation into Korean was done, then back translated into English only based on the Korean translation by the researcher who is bilingual in both languages. The back translation was compared by the original developer of MYMOP and confirmed usable. In order to test the existence of acupoints and meridians through popular forms of Korean acupuncture regimes, we aim at collecting opinions from 101 Korean clinicians that have used those forms. The questions asked include most effective symptoms, 5 Shu points, points those are least likely to use due to either adverse events or the lack of effectiveness, theoretical reasons for the above proposals, proposing outcome measures, and the time from insertion to be effective. The questionnaire is posted on the virtual notice board of the homepage of the communication KOMA (The official tool of Association of Korean Oriental Medicine).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.75-75
• /
• 2011

Recently, dye-sensitized solar cell (DSSC) attracts great attention as a promising alternative to conventional silicon solar cells. One of the key components for the DSSC would be the nanocrystalline TiO2 electrode, and the control of interface between TiO2 and TCO is a highly important issue in improving the photovoltaic conversion efficiency. In this work, we applied various interfacial layers, and analyzed their effect in enhancing photovoltaic properties. In overall, introduction of interfacial layers increased both the Voc and Jsc, since the back-reaction of electrons from TCO to electrolyte could be blocked. First, several metal oxides with different band gaps and positions were employed as interfacial layer. SnO2, TiO2, and ZrO2 nanoparticles in the size of 3-5 nm have been synthesized. Among them, the interfacial layer of SnO2, which has lower flat-band potential than that of TiO2, exhibited the best performance in increasing the photovoltaic efficiency of DSSC. Second, long-range ordered cubic mesoporous TiO2 films, prepared by using triblock copolymer-templated sol-gel method via evaporation-induced self-assembly (EISA) process, were utilized as an interfacial layer. Mesoporous TiO2 films seem to be one of the best interfacial layers, due to their additional effect, improving the adhesion to TCO and showing an anti-reflective effect. Third, we handled the issues related to the optimum thickness of interfacial layers. It was also found that in fabricating DSSC at low temperature, the role of interfacial layer turned out to be a lot more important. The self-assembled interfacial layer fabricated at room temperature leads to the efficient transport of photo-injected electrons from TiO2 to TCO, as well as blocking the back-reaction from TCO to I3-. As a result, fill factor (FF) was remarkably increased, as well as increase in Voc and Jsc.

• Geotechnical Engineering
• /
• v.2 no.3
• /
• pp.51-66
• /
• 1986

The design of fabric reinforced retaining wall structure was discussed in this article. It was confirmed that the reinforced retaining earth wall which was designed by new theoretical formulae developed this time was stable structurally and economically. The plastic fabric filter which was placed in layers behind the facing element reduced the lateral earth pressure on the wall elements in comparison with a conventional retaining earth walls. The reinforcing characteristics of earth wall was governed by the spacing of fabric layers, effective length of fabrics, particle distribution and compaction, and thus it is essential that, in the construction field, the reinforcing strips should be selected in order to develop the maximum friction forces bet.eon soil and fabric filters. The maximum tensile stress developed from the reinforcing strips was appeared at a little far distance from the back of skin element and it was not well agreed with the Rankine's theory but distributed well as a symmetrical shape against the point of the maximum tensile stress. The total length of the different layers should be sufficient so that the tension in the fabric strip could be transferred to the backfill material. Also the total stability of reinforced earth wall should be checked with respect to a failure surface which extended blond the different lathers.

• Journal of the Korean housing association
• /
• v.26 no.4
• /
• pp.105-118
• /
• 2015

The purpose of this study was to give a suggestion for vitalizing rural area's community, with respect to the components of community; 'locality' and 'communality'. The survey was conducted at Hondong, Hodongseong-gun, Chungcheongnam-do, which was a representative area for active rural area community. For the survey, we interviewed an activist on the village in November $9^{th}$, 2014, and let 81 residents fill the questionnaires during March $7^{th}$ to $14^{th}$, 2015. Major findings were as follows. 1) As for the 'locality' factor, the motives of residents' immigration were influenced by the availability of facilities for agriculture education, living, and convenience in the area. Most of residents recognized that the area comprises their own community facility area and expanded area with concentrated facilities of 'li', minimal adminstration unit. It means that their usage pattern of community facilities influences their conceptions of the village. 2) As for the 'communality' factor, original residents and immigrant back-to-farm residents showed different pattern in communicating with neighbors and community facility usages. Residents communicated with neighbors by meeting up or using the concentrated facilities in Gatgol, and visited the Balmak library frequently. Residents' sense of belonging was high with mean 4.16 point of 5.0 in Likert scale.