• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.52-58
• /
• 2000

Hot precision forging with a back pressure was investigated for manufacturing of compressor parts made of Al-Si alloy. Disk-shaped blank made of Al-Si alloy was hot forged, and ribs were formed by loading back pressure on their top. The influence of the back pressure and die temperature on forgeability and properties of parts made of Al-Si alloy were examined. Using the F.E.M. simulation, we found the optimum vallue of back-pressure. The prototypes of scroll parts were forged into the near-net shape and satisfied the required properties.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.38-43
• /
• 2021

Permanent magnet linear synchronous motor (PMLSM) is suitable for use in cleanroom environments and have advantages such as high speed, high thrust, and high precision. If the stators are arranged in the entire moving path of the mover, there is a problem in that the installation cost increases. To solve this problem, discontinuous armature arrangement PMLSM has been proposed. In this case, the mover receives a greater detent force in the section where the stator is not arranged. When a large detent force occurs, it appears as a ripple component of the thrust during PMLSM operation. If the shape of the stator is changed to reduce the detent force, the characteristics of the back EMF are changed. Therefore, in this paper, the detent force and the harmonic components of back EMF were reduced through multi-purpose shape optimization. To this end, the FEA model was constructed and main effect analysis was performed on the major shape variables affecting each objective function. Then, the optimal shape that minimizes the objective function was derived through the response surface analysis method.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.6
• /
• pp.425-430
• /
• 2017

In order to reduce the cost of corrections and time needed for the block assembly process, the reverse setting method is applied for a back-heated block to neutralize deck deformation. The proper reverse setting shape for a back-heated block to correct deformation improved the deck flatness, but an excessive amount of reverse setting could inversely affect the flatness of the block. A prediction method was developed for the proper reverse setting shape using a back-heated block, considering the complex geometry of blocks, thickness of the deck plate, and thermal loading conditions such as welding and back-heating. The prediction method was developed by combining the re-meshing technique and inherent strain-based deformation analysis using the finite element method. Because the flatness deviation was decreased until the lower critical point and thereafter it tended to increase again, the optimum value for which the flatness was the best case was selected by repeatedly calculating the predefined reverse setting values. Based on this analysis and the study of the back-heating deformation of large assembly blocks, including the reverse setting shape, the mechanism for selecting the optimum reverse setting value was identified. The developed method was applied to the actual blocks of a ship, and it was confirmed that the flatness of the block was improved. It is concluded that the developed prediction method can be used to predict the optimum reverse setting shape value of a ship's block, which will reduce the cost of corrections in the construction stage.

• The Research Journal of the Costume Culture
• /
• v.19 no.5
• /
• pp.1049-1060
• /
• 2011

The purpose of this study was to develop a shirt pattern that enhances the functionality of golf swing motions. The pattern was made with 3D body surface shape data that changed according to dynamic golf postures. The data were collected from the golf swing motions. The 3D body surface data in golf swing postures piled up on the 3D surface data in a static posture. The results showed that the surface shape data changed more in the address, back swing, and finish postures than the other swing postures. The experimental pattern was developed with 3D surface scan data in those three golf swing motions. The pattern had raglan sleeves and the front-bodied piece was divided into two pieces with a princess line, which comes from armscye line of the address posture. The back bodice piece was divided into three pieces with a yoke line and a back princess line. The yoke line was made by back shoulder shape in the back swing posture. The level of comfort of the experimental garment and commercial golf shirts was evaluated by 38 women golfers. The experimental garment pattern was evaluated to be more comfortable in golf swing postures than commercial golf shirts.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.5
• /
• pp.741-751
• /
• 2009

In order to design and develop the various silhouette of pants pattern for standardized pants patterns, this study is to classify the pants style by the silhouette and to characterize each pants pattern which are classified. Recent 37 ready-made pants patterns of various style were collected in order to analyze their silhouette from April to July 2007. Measurement of each region of the pants pattern were compared and analysed. After analyse the standard deviation, coefficient of variance, minimum, maximum, range about the measurement of each region of the pants pattern, major pattern design factors were extracted. Five major factors are the angle of center front line and center back line, the crotch extension, the position of center back line against center front line, the curvature of center back line, and amount of waist dart. As a result, pants style were grouped as the culottes, formal, basic and tight style after considering the extracted design factors, and analysing correlation, degree of dispersion of the measurement by part. As the silhouette of pants classification from culotte to tight, the fits are closer to the figure, crotch depth increases, crotch extensions are shorter, and angle of the center back increases. The shape of the connected front and back center lines is U-shape for culotte and is closer to V-shape as the silhouette becomes tight.

• The Research Journal of the Costume Culture
• /
• v.7 no.6
• /
• pp.140-158
• /
• 1999

The purposes of this study are to examine the characters of the lower body shape in the middle aged women and to make slacks pattern on the base of four difference body shapes. The lower body shapes were classified into 4 types on the basis of their lateral view silhouettes. The slacks patterns were based on the lower body shape characters and resulted in followings. In “Type 1” of the right body shape with the standard protrusion of abdomen and hips, little difference from conventional patterns was seen in experiment pattern, in which the front waist girth was W/4+0.5㎝+0.5㎝+fold(2.5㎝) and the back waist girth W/4+0.5㎝-0.5㎝+dart(3.5㎝). The front hip girth was defined as H/4+2.0㎝+0.5㎝ and the back hip girth as H/4+2.0㎝-0.5㎝ due to its increased ease amount produced by abdominal fat deposition. In the experimental pattern of “Type 2” with prominent hips, the front and back differences of the waist girth and the hip girth and the hip girth were defined as 1.0㎝ and 2.0㎝ separately. Accordingly, the front waist girth was W/4+0.5㎝+1.0㎝+fold(2.0㎝), the back waist girth W/4+0.5㎝-0.1㎝+dart(6.5㎝), the front hip girth H/4+2.0㎝+1.0㎝ and the back hip girth H/4+2.0㎝-1.0㎝. In “Type 3” with the prominent abdomen and the flat hips, the front waist girth was set up as W/4+0.5㎝+0.5㎝+fold(4.5㎝) for the increased front fold amount and the back waist girth was W/4+0.5㎝+0.5㎝+dart(3.0㎝). The front hip girth was made as H/4+2.5㎝+0.5㎝ and the back hip girth H/4+2.5㎝-0.5㎝. In “Type 4” with prominent abdomen and hips, considered were ① the increased front fold amount due to the abdominal protrusion, ② the increased back dart amount and the decreased back dart length owing to the hips prominent and ③ the front and back differences of waist and hip girth for the lateral view silhouette. Therefore the front waist girth was defined as W/4+0.5㎝+2.0㎝+fold(5.0㎝), the back waist girth as W/4+0.5㎝-2.0㎝+dart(4.0㎝), the front hip girth as H/4+2.0㎝+1.0㎝ and the back hip girth as H/4+2.0㎝-1.0㎝. The sensory evaluation of appearance and comfort was appeared more suitable on the experiment pattern than on the conventional pattern.

• Fashion & Textile Research Journal
• /
• v.12 no.5
• /
• pp.619-625
• /
• 2010

The purpose of this research is to analyze the shapes of blouse with above-elbow sleeves according to arm movements. The shapes include five types of the arm movement(basic posture, reach forward 45, 90, and reach lateral 45, 90) in the stand-posture, which were made by different adaptability of clothes. Experiments were conducted to figure out the dressed shape through 3-D measurement Vivid 910, and also to investigate the area of the shape of sleeves on the section map and the diagonal length of the block made by the basic section line in lateral part of sleeve with Rapid Form 2004, a software for 3-D shape analysis. The Data were analyzed by factor analysis, Anova, Duncan test, t-test. The results of this study were as follows: First, the area of sleeve was briefed 3 factor; front, center, back in sleeve. Second, there were different effect of arm movement, section level and part of shapes in the area of sleeve. Third, the diagonal length was briefed 4 factor; back, back-center, front-center, front. Forth, after t-test, there were statistically significant between the reach forward and lateral and between the angles of arm reach.

• The Research Journal of the Costume Culture
• /
• v.8 no.5
• /
• pp.668-680
• /
• 2000

The study presents the general types and individual differences of the shape of the adult women's neck and shoulder in our country. It is based on the average value, the standard deviation, the maximum value, the standard deviation, the maximum value, the minimum value and c.v. measured from the women at the age of 19 through 64. The results of this study are as follows ; 1. The factors by factor analysis are five. The first is the size factors of the neck and shoulder. The second is shape factor of neck. The third is plane view and length factor of the neck. The fourth is the side view factor of the neck and shoulder. The fifth is the shape factor of shoulder. Therefore the shape of the neck and shoulder should be examined in the shape factors as well as in the size factors as well as in the size factors for the designing body-suitable clothes. 2. The factors of the concrete objects are the solid view of neck and shoulder, the cross-sectional view of neck line, side view of neck and shoulder and length of neck. The explainable measuring items for the factors are the difference of the length between lower neck round line and the 4㎝ above neck round line, the length of neck, the angle of inclination between fore neck and back neck, the angle of inclination of the side shoulder, the difference of the height between fore neck point and back neck point, the width of shoulder, the width of chest and the width of back. 3. The concrete objects of the neck and shoulder have five types ; Type Ⅰ is average type, Type Ⅱ is thick short neck and the drooping shoulder type, Type Ⅲ I is slender long neck and lean-back shoulder type, Type Ⅳ is thick and rising shoulder type and Type Ⅴ is slender and drooping shoulder type.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.209-215
• /
• 2000

Precision forging technology that can control flow velocity of workpiece have been developed to minimize the amounts of machining. To get the uniform rib length, flow velocity distribution is needed to be estimated and controlled. Computer-aided design is known for very effective to estimate the deformation behavior and design the die for controlling the flow velocity. In this study, die design to control the deformation velocity are investigated using the DEFORM-2D about rib-web shape parts. Also we can get uniform rib length by enforcing the back pressure at end section of rib. The applied load of back pressure farming is lower than that of conventional forging. These results are analysed and confirmed by the experiment.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.04b
• /
• pp.715-717
• /
• 2004

This paper proposes a new reconstruction method of high-resolution facial image from a low-resolution facial image based on a recursive error back-projection of top-down machine learning. A face is represented by a linear combination of prototypes of shape and texture. With the shape and texture information about the pixels in a given low-resolution facial image, we can estimate optimal coefficients for a linear combination of prototypes of shape and those of texture by solving least square minimization. Then high-resolution facial image can be obtained by using the optimal coefficients for linear combination of the high-resolution prototypes, In addition to, a recursive error back-projection is applied to improve the accuracy of synthesized high-resolution facial image. The encouraging results of the proposed method show that our method can be used to improve the performance of the face recognition by applying our method to reconstruct high-resolution facial images from low-resolution one captured at a distance.