• Journal of Radiation Protection and Research
• /
• v.35 no.2
• /
• pp.57-62
• /
• 2010

Maintenance on the water chamber of steam generator, the change of pressurizer heater, the removal of pressure tube feeder, and so on during outage in nuclear power plants (NPPs) has a likelihood of high radiation exposure to whole body of workers even short time period due to the high radiation exposure rates. In particular, it is expected that hands would receive the highest radiation exposure because of its contact with radiation materials. In this study, field tests on extremity dose assessment of radiation workers for contact works with high radiation exposure were conducted during the maintenance periods in Korean pressurized water reactors (PWRs) and pressurized heavy water reactors (PHWRs). In this field test, radiation workers were required to wear additional TLDs on the back and wrist, and an extremity dosimeter on fingers including a main TLD on the chest, while performing maintenance. As a result, it was found that the equivalent dose for fingers was distributed in the fixed range of deep dose and the equivalent dose for wrists.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.31-42
• /
• 2000

Consolidation and permeability are major engineering properties of soil. In clay, coefficient of permeability and consolidation can be calculated by incremental loading consolidation test. However, it is known that the incremental loading test has several deficiencies including long testing time, non-uniform stress state, very soft clay and problem of back pressure saturation. Specially, it is not performed with horizontal consolidation test. Several methods have been proposed for obtaining reliable values of $C_v$. Among these, the square root of time-fitting method proposed by Taylor(1948) and logarithm of time-fitting method, also called Casagrande's method, are used extensively in soil engineering practice. But these methods are not amenable for the absence of initial linear portion and have the difficulties involved in distinguishing secondary compression from primary compression. Rowecell consolidation tests were carried out in this study with different trimming axis and sample size. The results were compared with those of other methods; Casagrande,$Taylor,\; Casagrande,\; Hyperbolic,\; \delta/t-logt$. From the results, we explained a relationship between horizontal coefficient of permeability and void ratio was obtained. Finally, the directly measured horizontal coefficient of permeability obtained by using the Rowecell was compared with the permeability derived indirectly from the consolidation test result.

• The Journal of Engineering Geology
• /
• v.32 no.4
• /
• pp.643-659
• /
• 2022

Geologic sequestration technologies such as CCS (carbon capture and storage), EGS (enhanced geothermal systems), and EOR (enhanced oil recovery) have been widely implemented in recent years, prompting evaluation of the mechanical stability of storage sites. As fluid injection can stimulate mechanical instability in storage layers by perturbing the stress state and pore pressure, poroelastic models considering various injection scenarios are required. In this study, we calculate the pore pressure, stress distribution, and vertical displacement along a surface using commercial finite element software (COMSOL); fault slips are subsequently simulated using PyLith, an open-source finite element software. The displacement fields, are obtained from PyLith is transferred back to COMSOL to determine changes in coseismic stresses and surface displacements. Our sequential use of COMSOL-PyLith-COMSOL for poroelastic modeling of fluid-injection and induced-earthquakes reveals large variations of pore pressure, vertical displacement, and Coulomb failure stress change during injection periods. On the other hand, the residual stress diffuses into the remote field after injection stops. This flow pattern suggests the necessity of numerical modeling and long-term monitoring, even after injection has stopped. We found that the time at which the Coulomb failure stress reaches the critical point greatly varies with the hydraulic and poroelastic properties (e.g., permeability and Biot-Willis coefficient) of the fault and injection layer. We suggest that an understanding of the detailed physical properties of the surrounding layer is important in selecting the injection site. Our numerical results showing the surface displacement and deviatoric stress distribution with different amounts of fault slip highlight the need to test more variable fault slip scenarios.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.1-11
• /
• 2007

This study aims to investigate, review, and summarize the definition, development, and applications of "percent agent in pipe", "percent of agent in pipe" which is used as a key factor in testing and evaluating the performance of gaseous fire extinguishing agents, including Halon 1301 and $CO_2$. This study also analyzes and compares the local and international standards on testing and evaluating the performance of gaseous fire extinguishing systems, as well as the results of system performance tests conducted as a part of performance evaluation and approval programs for gaseous fire extinguishing systems, especially, Korean Gaseous Fire Extinguishing System Performance Approval Program called KFI Approval. Percent agent in pipe was defined first in NFPA 12A, Standard on Halon 1301 Fire Extinguishing Systems, dating back to the 1970's. After the phaseout of Halon 1301 systems in 1994 in the developed countries, the percent agent in pipe has been widely used in Halon 1301 alternative clean agent fire extinguishing systems, both halocarbon clean agent systems and inert gas clean agent systems, as an essential criterion to assure the system design accuracy, determine the limitations and performance of a system, and to predict the system performance results accurately, especially, in association with their system flow calculations. Underwriters Laboratories has their own standards such as UL 2127 and 2166 applying percent agent in pipe in testing and evaluating the performance of clean agent fire extinguishing systems. As a part of a system performance test and approval program called KFI Approval System, Korea also has started to apply the percent agent in pipe as a key factor to test, evaluate, and approve the performance of gaseous fire extinguishing systems, including both high and low pressure $CO_2$ systems, from the early 2000's. This study outlines and summarizes the relevant UL and KFI standards and also describes the actual test resultant data, including the maximum percents of agent in pipe for gaseous fire extinguishing systems. As evidenced in lots of tests conducted as a part of the system performance test and approval programs like KFI Approval System, it has been proven that the percent agent in pipe may work as a key factor in testing, evaluating, and determining the limitations and performance of gaseous fire extinguishing systems, especially compared with the hydraulic flow calculations of computer design programs of gaseous fire extinguishing systems, and will remain as such in the future. As one thing to note, however, there are some difficulties in using the unified percent agent in pipe to determine the maximum lengths of pipe networks for gaseous fire extinguishing systems, because the varying definitions used by some of the flow calculations (not in accordance with NFPA 12A definition) make it impossible to do any direct comparison of pipe lengths based on percent agent in pipe.

• Korean Journal of Human Ecology
• /
• v.21 no.2
• /
• pp.299-314
• /
• 2012

The purpose of this study was to explore effects of pattern alteration using a virtual clothing simulation approach in combination with 3D analysis software. Three raglan sleeves of different patterns were worn by an avatar using virtual clothing simulation with silk and cotton as the test fabrics. It was observed that the silhouette and hemline shape were affected differently based on raglan sleeve pattern and fabric type. By examining clothing pressure distribution, the cotton fabric designs and pattern shapes provided for a variety of influences on armhole and bust regions as well as the back sleeve area. For representative locations, cross section circumstance, cross section area, and volume were measured by using 3D analysis and the resulting correlation between the 2D and 3D data were investigated. Among different fabrics, there was little difference between the 2D and 3D clothing surface area. However, when using 3D analysis, clothing volume was significantly affected by different fabrics and pattern types. By simultaneously adopting the virtual simulator and 3D analysis, quantitative assessment of virtual clothing simulation was successfully conducted. In light of the results of this study, the resulting methodology is expected to be used as a comprehensive evaluation tool for virtual clothing simulation wear testing.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.5
• /
• pp.43-53
• /
• 2014

This paper presents a the study on air curtain system of top and bottom bi-directional jet air discharge for blocking the spread of smoke in case of tunnel fire. The five kinds different air curtains of A, B, C, D, and E of models for various performance tested after manufactured. A results of the various performance test obtained the best efficiency from E model air curtain. And optimize the injection angle of the air curtain nozzle through the three-dimensional computational fluid dynamics (CFD) analysis and analyzed the effects of external pressure of tunnel. and also single factor design have been applied. At present, our attention is focused on the velocity distribution(flow width and flow position) of 1.5m on the ground in tunnel. Also, analyzed the influence of draft in the tunnel. Detailed effects of discharge angle of air curtain and velocity at nozzle exit are discussed.

• Journal of Korean Clinical Nursing Research
• /
• v.21 no.2
• /
• pp.215-222
• /
• 2015

Purpose: For hemodialysis, a vascular access which can maintain a certain speed for a long time is required. The prevention of the vascular access dysfunction is very important to decrease morbidity and to improvethe quality of life of patients receiving hemodialysis It is reported that far infrared heat increases the blood flow by expanding capillaries and micro-arteriovenouses. This study aimed to evaluate the effect of far infrared heat therapy as a new nursing intervention for maintaining vascular access function and improving the blood flow of patients receiving hemodialysis. Methods: The quasi-experimental research of nonequivalent control group pre-post test design was carried out for 59 patients receiving hemodialysis 3 times per week at K medical center. A far infrared heat was applied to the experimental group for 3 months. Results: The arteriovenous fistula blood flow of the experimental group (far infrared heat therapy group) increased significantly when compared to the control group (p=.047). However, static intra-access pressure ratio(SIAPR)was not different statistically (p=.101). Conclusion: The far infrared therapy could be considered as nursing intervention of choice as it demonstrated increase in the arteriovenous fistula blood flow in the patients receiving hemodialysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.4
• /
• pp.551-561
• /
• 1998

This paper was studied to understand the characteristics of heat transfer coefficients and surface temperature distributions around a circular combustion chamber within the heat-intercept duct of kerosene fan heater. The experiment was carried out in the heat-intercept duct of kerosene fan heater attached to the blow-down-type subsonic wind tunnel with a test section of 240 mm * 240 mm * 1200 mm. The purpose of this paper was to obtain the basic data related with normal combustion for new design from conventional kerosene fan heater, and to investigate the effect of surface temperature, local and mean heat transfer coefficients versus flow-rate of convection axial fan according to the variations of heat release conditions from kerosene fan heater during normal combustion. Consequently it was found that (i) the revolution of convection axial fan during combustion had a smaller value than that of non-combustion because of the thermal resistance due to the high temperature in the heat-intercept duct, (ii) the pressure ratio P$_{2}$/P$_{1}$ had a comparatively constant value of 0.844 according to the revolution increase of turbo fan and the heating performance of kerosene fan heater had a range of 1,494 ~ 3,852 kcal/hr, (iii) the local heat transfer coefficient around a circular combustion chamber had a comparatively larger scale in the range of 315 deg. < .theta. < 45 deg. than that in the range of 90 deg. < .theta. < 270 deg. as a result of heat transfer difference between front and back of a circular combustion chamber, and (iv) the mean heat transfer coefficient around a circular combustion chamber increased linearly like a H$_{m}$=95.196Q+104.019 in condition of high heat release according to the increase of flow-rate of axial fan.n.

• Fashion & Textile Research Journal
• /
• v.17 no.3
• /
• pp.429-439
• /
• 2015

This study develops a new brassiere for new silver women. A new brassiere design was developed for the silver generation based on apreliminary survey; subsequently, a wire and no-wire type of brassier were developed after a second fitting evaluation. The results were as follows. First, in terms of brassiere design, the cup shape was designed as mold type full cup, shoulder straps were designed as camisole type with cups, bias tape was designed for body correction in the side line and mash tape was designed for easy movement below the cups. On the other side ofthe cup shape was a pocketdesigned on a support pad forthe wire type and a support panel to serve as a wire in the no-wire type brassiere. Second, brassiere patterns were designed by referencing the educational H pattern. Thetotal length was elongated by 5cmto reduce pressure when wearing a brassiere and the height of the front center increased by 8cm for the stability of the front center of the brassiere. In addition, the side line was moved back by 3cm and the width of the brassiere wings was designed widely at 10.5cm. Third, a wearing test was conducted for the wire type and the no-wire type brassiere with comparison products, using a 7-point Likert scale. Appearance results and movement tests for the wire and no-wire type showed a higher score than comparison products.

• Nuclear Engineering and Technology
• /
• v.38 no.6
• /
• pp.585-590
• /
• 2006

This paper describes the results of an irradiation test and the specifications of the pneumatic transfer system (PTS) in the NAA #3 irradiation hole at the HANARO research reactor, which was reinstalled after some modifications of the operation mode at the end of 2004. The outer and inner diameters of the PE transfer tube are 34.1 and 27.5 mm, respectively. PE rabbit was used for sample irradiation. The $N_2$ gas pressure of the PTS lines was adjusted to 0.75 bar. The average sending time to the reactor was $8.5{\pm}0.3$ s and the average receiving time back to the receiver was $3.2{\pm}0.2$ s. The internal and external temperature of the irradiation tube was measured in a range of 50 to $80^{\circ}C$ for a 40 s to 80 s irradiation time, respectively. The optimum irradiation time was estimated to be less than 80 s. The thermal, epithermal and fast neutron flux at 30 MW thermal power were $1.42{\pm}0.01{\times}10^{14},\;1.51{\pm}0.04{\times}10^{13}$ and $9.48{\pm}0.69{\times}10^{11} n{\cdot}cm^{-2}{\codt}s^{1-}$, respectively. The cadmium ratio was approximately 9.40. The data obtained will be applied to supplement user information and for reactor management.