• 전기학회논문지
• /
• 제66권9호
• /
• pp.1325-1333
• /
• 2017

The sensorless control of blushless DC motor(BLDCM) is based on the $120^{\circ}$ control in which the back electromotive force(Back EMF) for estimating the position of the rotor can be detected. However, the $120^{\circ}$ control has a disadvantage that the torque constant is small as compared with $180^{\circ}$ control which can not detect the back EMF. The $150^{\circ}$ control which complements these problems makes it possible to detect the back EMF and improve the torque constant by 12.5% compared to the $120^{\circ}$ control. Therefore, this paper compares the output characteristics of BLDCM through finite element method analysis (FEA) by the conventional and proposed control methods of BLDCM for water circulation system and proposes design for downsizing and weight reduction of BLDCM according to secured torque constant. The validity of the proposed control and design proposal is proved through simulation and experimental results by comparing the output characteristics of $120^{\circ}$ control and $150^{\circ}$ control.

• 전력전자학회논문지
• /
• 제25권4호
• /
• pp.329-332
• /
• 2020

A back-electromotive force (back-EMF) estimator for a permanent magnet synchronous motor (PMSM) uses the three-phase voltage references of a current controller to estimate rotor position. However, owing to voltage drops caused by the nonlinear characteristics of switches and passive components, the actual voltage in the motor and the three-phase voltage reference may not match. This study proposes a sensorless control method using a sine-wave output filter applied between the motor drive system and PMSM. The precise voltage in the motor can be measured with the sine-wave output filter and applied to the input of the estimator. Moreover, given that the voltage in the motor can be measured precisely at extremely low speeds, the stable operation range of the back-EMF estimator can be secured. Experimental results show that the proposed sensorless control method has stable operation at extremely low speeds compared with conventional sensorless control.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권1호
• /
• pp.1-7
• /
• 2004

This paper presents a sensorless control strategy of a PMSM(Permanent Magnet Sycchoronous Motor). This method is very simple to compute the position angle of a rotor. A principle and a practical solution are described. A sensorless control algorithm is proposed to remove a mechanical position sensor. The theory is based on the superposition principle. The state equation of a motor is divided into two conditions: one is the state equation of exciting voltage and phase current in a constraint, the other is the state equation of back EMF(Electromotive Force) and phase current in a short circuit. Based on the analysis, short circuit current by back EMF is computed and then the information of position angle is calculated. The proposed method is verified by experimental results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권2호
• /
• pp.71-80
• /
• 2005

This paper presents the position sensorless vector control of a cylindrical permanent magnet synchronous motor(PMSM) in the field weakening region. The position sensorless algorithm using an instantaneous reactive power of the PMSM is proposed. An instantaneous reactive power can be obtained from the vector product of rotor currents and back emf of the PMSM. Back emf includes the information of rotor speed. So the estimated speed can be yielded from the voltage equation of the PMSM. In other words, the estimated speed is compensated by using an instantaneous reactive power. To extend the speed range of the PMSM in the constant horsepower region, the field weakening control is applied. The proposed algorithm is not affected by mechanical motor parameters because the mechanical equation is not used. The effectiveness of the proposed algorithm is verified by the experimental results.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.95-102
• /
• 2014

This paper presents zero crossing point(ZCP) estimation methods considering discretization error for a high speed brushless DC(BLDC) motor drive. The ZCP is estimated by detecting the change of back-EMF polarity for the BLDC sensorless drive, and the discretization error exist on the estimated ZCP. The discretization error of the ZCP is a cause of the delay of a commutation timing of current and increment of a current ripple factor. Besides a delay of a ZCP estimation brings on the limitation of a speed range for the BLDC sensorless drive. The compensation method based on the error analysis with probability theory for reducing the effects of the discretization error of the ZCP is proposed. Also a ZCP estimation method according to the Back-EMF patterns is proposed to widen the speed range for the BLDC sensorless drive. The proposed methods are verified by the experiment.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.956-962
• /
• 2013

Recently, sensorless controls, which eliminate position and speed sensor in a permanent magnet synchronous motor drive, have been much studied. Most sensorless control algorithms are based on the back-EMF and speed estimations which are obtained from the voltage equations. Therefore, the sensorless control performance is largely affected by the parameter errors of a motor. This paper investigates a novel adaptive control with the parameter error compensation for the speed sensorless control of a permanent magnet synchronous motor. The proposed parameter estimation is obtained from the d-axis current error between the real and estimated currents. The proposed algorithm is verified through the simulation and experimentation.

• 전력전자학회논문지
• /
• 제16권6호
• /
• pp.602-609
• /
• 2011

본 논문은 역기전력 기반 센서리스 제어 시 안정적인 기동성능 확보를 위한 간단한 초기 회전자 위치추정 방법을 제안하였다. 제안된 방법은 전동기의 고정자 권선 인덕턴스의 차이에 의한 전류응답특성을 이용하여 초기 회전자 위치를 추정한다. 이러한 초기 회전자 위치추정 방법은 알고리즘 구현이 간단하고 추가적인 외부회로가 불필요하며, 전동기 상수의 영향을 받지 않는다. 제안된 방법의 타당성은 실험결과를 통하여 검증하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1988년도 한국자동제어학술회의논문집(국내학술편); 한국전력공사연수원, 서울; 21-22 Oct. 1988
• /
• pp.706-710
• /
• 1988

Using back electro-motive force(EMF) signals of a brushless DC motor, the sensorless micro-processor controlled drive system was developed. In this new commutation method, the manual pulses are used for relatively short accelerating phase and then the exact commutational positions are detected based upon the back emf signals. The hardware and software implementations with the experiment to compare the performance of the developed system with the, conventional system using hall effect sensors are included. By reducing the number of the required sensors in the artificial heart control system, the total reliability will be incresed.

• 전기학회논문지
• /
• 제67권5호
• /
• pp.635-643
• /
• 2018

This paper propose a method to identify the motor parameters and improve input voltage error which affect the low speed position error of the back-emf(back electromotive force) based sensorless algorithm and to secure the operation reliability and stability even in the case where the load fluctuation is severe and the start and low speed operation frequently occurs. In the model-based observer used in this paper, stator resistance, inductance, and input voltage are particularly influential factors on low speed performance. Stator resistance can cause resistance value fluctuation which may occur in mass production process, and fluctuation of resistance value due to heat generated during operation. The inductance is influenced by the fluctuation due to the manufacturing dispersion and at a low speed where the change of the current is severe. In order to find stator resistance and inductance which have different initial values and fluctuate during operation and have a large influence on sensorless performance at low speed, they are commonly measured through 2-point calculation method by 2-step align current injection. The effect of voltage error is minimized by offsetting the voltage error. In addition, when the command voltage is used, it is difficult to estimate the back-emf due to the relatively large distortion voltage due to the dead time and the voltage drop of the power device. In this paper, we propose a simple circuit and method to detect the voltage by measuring the PWM(Pulse Width Modulation) pulse width and compensate the voltage drop of the power device with the table, thereby minimizing the position error due to the exact estimation of the back-emf at low speed. The suitability of the proposed algorithm is verified through experiment.

• 전기학회논문지P
• /
• 제59권2호
• /
• pp.135-140
• /
• 2010

This paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor. Depending on the terminal voltage sensing rotor position, active filter is used for position information. This leads to a significant reduction in the component device of the sensorless circuit. Therefore this is a advantage for the cost saving and size reduction. With indirect sensing methods based on detection of the terminal voltage that require active filtering, the position information needs the six divider section by PLL circuit, the binary counter and johnson counter by the EPLD. Finally, this algorithm can estimate the rotor position information similar to Hall-sensor sticked the three-phase BLDC motor. As a result, the method described that it is not sensitive to filtering delays, allowing the motor to achieve a good performance over a wide speed range. In addition, a simple starting method and a speed estimation approach are also proposed. Experimental and simulation results are included to verify the proposed scheme.