• The Korean Journal of Ceramics
• /
• v.2 no.4
• /
• pp.238-241
• /
• 1996

New porous BaTiO$_3$ thermistors were fabricated using graphite powders (0 to 10 wt. %) and their porosities were in the range of 9.1% to 16.2%. As results of impedance analysis, it was confirmed that the pores affected the grain-boundary resistance and the bulk (grain interior) resistance was constant as about 25 $\Omega$ at room temperature. The magnitude of PTCR effect $(p_{max}/p)$ markedly increased from 3 orders to 7 orders without addition of any acceptor dopant such as Mn or Cr.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.42-45
• /
• 1992

In this study, the structural, dielectric and electrical properties of $0.85Pb(Zn_{1/3}Nb_{2/3})O_3-0.1BaTiO_3-0.05PbTiO_3$ ceramics were investigated with respect to the variations of $La_2O_3$ addition amount. The specimen with 0.2 [wt%] $La_2O_3$ addition amount, which has the coupling constants with the value of $k_p$=44.8[%]. $k_{31}$=25.4[%] and the piezoelectric constant with $d_{31}=100{\times}10^{-12}$[C/N] respectively, exhibits the relatively good values in the applications of electrostriction actuators.

• Korean Journal of Crystallography
• /
• v.7 no.2
• /
• pp.165-174
• /
• 1996

The effects of Ba2+, Sr2+, and Ca2+-substitutions for Pb2+ at Pb(Zr0.52Ti0.48)O3 composition were studied for thier dielictric, piezoelectric, and aging properties. For relative dielectric constants and electromechanical coupling factors, the Ba2+-substituted composition was the highest and the Ca2+-substityed composition was the lowest. In the case of mechanical quality factors, the opposite behavior occurred. Time dependence of frequency for various ion-substituted compositions is similar to that of non-substituted composition. The piezoelectric properties after aging at high temperature was the worse than that after aging at room temperature.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.826-834
• /
• 2004

In this paper, we fabricated thick film monopole antennas using Bi$_2$O$_3$-doped BaTi$_4$$O_{9}$ ceramics for small size and broadband intenna. In the result, the high permittivity was fixed and the quality factor was also significantly decreased by the formation of secondary phase of Bi$_4$Ti$_3$O$_{12}$ repleced by addtion Bi. The antenna property influenced by the quality value more than the permittivity. The bandwidth of antenna was increased to 33 %. On the other hand, the gain was reduced to -4.3 dBi. Also radiation patterns were showed low dBi value by increasing of dielectric loss. Specially, Measured x-y plane radiation patterns was distorted as the dispersion of wavelength and high permittivity difference. But the result is showed execellent bandwidth because of low quality value in all formation range.nge.

• Electrical & Electronic Materials
• /
• v.1 no.4
• /
• pp.311-318
• /
• 1988

초음파센서(수신기)에 응용가능한 압전세라믹스를 제조하기 위하여 Ba변조된 Pb(ZR, Ti)O$_{3}$계 세라믹스에 MnO$_{2}$를 첨가하여 첨가량과 소성온도에 따른 영향을 조사하였다. 또한 제조된 압전세라믹스를 이용하여 초음파 수신기를 제작하여 수신특성을 확인하여 보았다. 그 겨로가 MnO$_{2}$가 0.4(wt%)첨가되었을 때 압전 g정수가 가장 크고 수신감도가 우수한 것으로 밝혀졌다.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.4
• /
• pp.116-120
• /
• 2009

Ceramic-polymer composites have been investigated for their suitability as embedded capacitor materials because they combine the processing ability of polymers with the desired dielectric properties of ceramics. This paper discusses the dielectric properties of the ceramic ($BaTiO_3$)-polymer (Epoxy) composition as a function of ceramic particle size at a ceramic loading of 40 vol%. The dielectric constant of these ceramic-polymer composites increases as the powder size decreases. Results show that ceramic-polymer composites have a high dielectric constant associated with the $BaTiO_3$ powder with a 200 nm particle size, high insulation resistance, high breakdown voltage (> 22 KV/mm), and low dielectric loss (0.018-0.024) at 1 MHz.

• The Korean Journal of Ceramics
• /
• v.3 no.4
• /
• pp.274-278
• /
• 1997

(Ba, Sr) TiO$_3$(BST) thin films were prepared on RuO$_2$/Si substrates by rf magnetron sputtering and annealing was followed at temperatures ranging from 550 to 80$0^{\circ}C$ in $N_2$or $O_2$atmosphere. The effects of annealing conditions on the properties of BST film deposited on RuO$_2$bottom electrodes were investigated. It was found that the crystallinity. surface roughness, and grain size of BST films vary with the annealing temperature but they are not dependent upon the annealing atmosphere. The flat region in the current-voltage (I-V) curves of BST capacitors shortened with increasing annealing temperature under both atmospheres. This is believed to be due to the lowering of potential barrier caused by unstable interface and the increase of charge The shortening of the flat region by $O_2$annealing was more severe than that by $N_2$-annealing. As a result, there was no flat region when the films were annealed at 700 and 80$0^{\circ}C$ in $O_2$atmosphere. The dielectric properties of BST films were improved by annealing in either atmosphere. however, a degradation with frequency was observed when the films were annealed at relatively high temperature under $O_2$atmosphere.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.189-189
• /
• 2008

Due to the environmental issue vast research is going on to replace the widely used lead contented piezoelectric materials. Bismuth sodium titanate (abbreviated as BNT) based bismuth sodium titanate-barium titanate (abbreviated as BNBT) ceramic was prepared by using modified method rather than conventional mixed oxide method. This modification was made to improve the properties of BNT based ceramic. In this procedure $BaTiO_3$ (abbreviated as BT) was prepared using conventional mixed oxide method. Analytical grade raw materials of $BaCO_3$ and $TiO_2$ were weighted and ball milled using ethanol medium. The mixed slurry was dried and sieved under 80 mesh. Then the powder was calcined at $1100^{\circ}C$ for 2 hours. This calcined BT powder was used in the preparation of BNBT. Stoichiometric amount of $Bi_2O_3$, $Na_2CO_3$, $TiO_2$ and BT were weighted and mixed by using ball mill. The used calcination temperature was $850^{\circ}C$ for 2 hours. Calcined powder was taken for another milling step. BNBT disks were pressed to 15 mm of diameter and then cold isostatical press (CIP) was used. Pressed samples were sintered at $1150^{\circ}C$ for 2 hours. The SEM microstructure analysis revealed that the grain shape of the sintered ceramic was polyhedral and grain boundary was well matched where as the sample prepared by conventional method showed irregular arrangement and grain boundary not well matched. And sintered density was better (5.78 g/cc) for the modified method. It was strongly observed that the properties of BNBT ceramic near MPB composition was found to be improved by the modified method compare to the conventional mixed oxide method. The piezoelectric constant dB of 177.33 pC/N, electromechanical coupling factor $k_p$ of 33.4%, dielectric constant $K_{33}^T$ of 688.237 and mechanical quality factor $Q_m$ of 109.37 was found.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.258-261
• /
• 2000

Highly (h00)-oriented (Ba, Sr)TiO$_3$(BST) thin films were grown by pulsed laser deposition on the perovskite LaNiO$_3$(LNO) metallic oxide layer as a bottom electrode. The LNO films were deposited on SiO$_2$/Si substrates by rf-magnetron sputtering method. The crystalline phases of the BST film were characterized by x-ray $\theta$-2$\theta$, $\omega$-rocking curve and $\psi$-scan diffraction measurements. The surface microsturcture observed by scanning electron microscopy was very dense and smooth. The low-frequency dielectric responses of the BST films grown at various substrate temperatures were measured as a function of frequency in the frequency range from 0.1 Hz to 10 MHz. The BST films have the dielectric constant of 265 at 1 kHz and showed multiple dielectric relaxation at the low frequency region. The origin of these low-frequency dielectric relaxation are attributed to the ionized space charge carriers such as the oxygen vacancies and defects in BST film, the interfacial polarization in the grain boundary region and the electrode polarization. We studied also on the capacitance-voltage characteristics of BST films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.11
• /
• pp.1178-1185
• /
• 2004

In the atmosphere of $N_2$ gas, BaZ $r_{0.08}$ $Ti_{0.92}$ $O_3$ polycrystal was grown by floating zone technique using BaZ $r_{0.08}$ $Ti_{0.92}$ $O_3$ ceramics as a feed and SrTi $O_3$(1l0) single cystal as a seed. The dielectric constant and loss at 10 kHz, 100 kHz, and 1 MHz for the as-grown sample were measured as a function of temperature in the temperature range between -10$0^{\circ}C$ and 150 $^{\circ}C$ to find a dielectric peak with frequency dispersion at Curie point. The hysteresis loop showed that the grown sample had very small polarization which was 0-0.01 $\mu$C/$\textrm{cm}^2$ for the applied dc-electric fields from -7 kV/cm to +7 kV/cm. However, the normal hysteresis loop was appeared after oxygen annealing. The electric-field dependence of the dielectric constant for both the as-grown and the post-annealed samples was studied by measuring the dielectric constants as a function of the biased-electric fields and their tunability was figured out from it at room temperature(27 $^{\circ}C$) and cryotemperature( -73$^{\circ}C$). Tunability for the as-grown sample was 51 % and the figure of merit 20.4 at 10kHz with the biased electric-field of 12 kV/cm. The tunability for the grown sample may be increased up to 80 % if the electric field of 25 kV/cm is applied. Tunability for the post-annealed sample was 41 % and the figure of merit 10.3 at 10 kHz with the biased electric-field of 12 kV /cm. Post-annealing improved the crystallinity of the as-grown sample but decreased its tunability.ability.