• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.27-28
• /
• 2009

In this study, we have fabricated the 3 wt% $Li_2CO3$ doped $(Ba,Sr)TiO_3$ thick films on the Ag/Pd printed $Al_2O_3$ substrates for the LTCCs (Low Temperature Co-fired Ceramics) applications. From the X-ray diffraion analysis, 3 wt% $Li_2CO3$ doped BST thick films on the Ag/Pd printed $Al_2O_3$ substrates, which sintered at 900 $^{\circ}C$ have perovskite structure without any pyro phase. The dielectric properties of 3 wt% $Li_2CO3$ doped BST thick films were measured from 1 kHz to 1 MHz. To investigate the electrical properties of 3 wt% $Li_2CO3$ doped BST thick films, we employed the impedance spectroscopy. The complex impedance of 3 wt% $Li_2CO3$ doped BST thick films were measured from 20 Hz to 1 MHz at the various temperatures.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.132-139
• /
• 2005

Sintering behavior of $BaO-Nd_{2}O_3-TiO_2$ with a Pb-based glassceramics frit were investigated in order to understand an effect of glassceramics as a low temperature sintering agent on dielectric ceramics. A green sheet form was fabricated through tape casting method with the glassceramic fut added $BaO-Nd_{2}O_3-TiO_2$. The dispersion properties, rheological properties and final density of dielectric composit slurry as a function of amount and composition of organic additives was examined. The dispersants' addition was effective in controlling dispersion of the ceramics in solution. The addition of excessive dispersant showed adverse effect on dispersion. The prepared slurries, containing ceramic : powders, glass-ceramics and various kinds of organic viechles, exhibited typical shear thinning behavior. The best properties of tape casting appeared powder to solvent ratio 65 : 35 and amount of the binder 6 wt$\%$ and plasticizer 3 wt$\%$. The viscosity of the slurry was 677 cps and green/sintered density in the tape was $3.3 g/cm^3,\;5.56 g/cm^3$ respectively.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.204-208
• /
• 1991

In this paper, the radiation properties of a far-Infrared using a PTC thermistor, the $BaTiO_3$+1.63mol% $Al_2O_3$+3.75mol% $SiO_2$+1.25mol% $TiO_2$(1/3 $Al_2O_3+xSiO_2$+(1-x) $TiO_2$; total x: 6.67mol%) ceramics, in order to progress the grade resistivity characteristics, by adding an ethanol solution of $Mn(NO_3){\cdot}6H_2O$ was investigated. The ceramics was fabricated by wet-mill method. The sintering temperature read 1300-1350$[^{\circ}C]$ and the holding time was 3 hours. The quantity of $Sb_2O_3$ and $Al_2O_3$ for an activation of the far-infrared radiation in ceramics was doped. In sintering, R-T property was measured by varying the grade temperature. The anatase-lighting apparatus and microstructures by using XRD and SEM were observed. $Sb_2O_3$. oxides additive. affected the semiconducting and emissivity and MnO was devoted an increase of resistivity. The specimen which only $Sb_2O_3$ is added to was high appeared far-infrared emissivity and Mno was not affacted the far-infrared radiation. The ceramics shows that it is effective in the structure of the human bodies as organic bodies and can be applied as electron device.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.178-183
• /
• 2016

Ferroelectric relaxor ceramics with $BaTiO_3-NaNbO_3-Bi(Mg_{1/2}Ti_{1/2})O_3$ ternary compositions (BT-NN-BMT) have been prepared by sol-gel powder synthesis and consequent bulk ceramic processing. Through the modified chemical approach, fine and single-phase complex perovskite compositions were successfully obtained. Temperature and frequency dependent dielectric properties indicated typical relaxor characteristics of the BT-NN-BMT compositions. The ferroelectric-paraelectric phase transition became diffusive when NN and BMT were added to form BT based solid solutions. BMT additions to the BT-NN solid solutions affected the high temperature dielectric properties, which might be attributable to the compositional inhomogeneity of the complex perovskite and resulting weak dielectric coupling of the Bi-containing polar nanoregions (PNRs). The temperature stability of the dielectric properties was good enough to satisfy the X9R specification. The quasi-linear P-E response and the temperature- stable dielectric properties imply the high potential of this ceramic compound for use in high temperature capacitors.

• Electrical & Electronic Materials
• /
• v.3 no.3
• /
• pp.233-241
• /
• 1990

본 연구에서는 xPb(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-yBa(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-zPbTiO(0.50.leq.x.leq.0.60, 0.10.leq.y.leq.0.20, 0.20.leq.z.leq.0.40)세라믹을 1050.deg.C에서 2시간동안 유지시켜 일반소성법으로 제작하였다. 시편 제작시 조성은 조성변태 상경계부근을 선택하였으며 Ba(Zn$_{1}$3/ Nb$_{2}$3/)O$_{3}$ 고용량에 따른 purochlore상의 억제 및 그 영향을 조사하고 구조적, 유전적 및 압전적 특성을 측정하였다. X-선 회절분석 및 미세구조의 관찰 결과, Ba(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$의 고용량에 따라 pyrochlore상 및 미반응 물질등은 억제되어 0.20mol 고용된 시편에서는 균질한 perovskite상이 형성되었다. Ba(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$의 고용량이 증가함에 따라 유전상수는 증가하여 0.50PZN-0.20BZN-0.30PT시편의 경우 6880.9의 높은 값을 나타내었으며 정전용량의 온도계수는 감소하여 0.383[%/.deg.C]의 양호한 값을 나타내었다. 큐리온도는 PbTiO$_{3}$의 고용량이 0.20mol에서 0.40mol로 증가함에 따라 30.deg.C에서 170.deg.C로 증가하였다. 전기기계 결합계수 (K$_{p}$), 기계적 품질계수(Qm) 및 압전전하 계수 (d$_{33}$)는 조성변태 상경계 부근의 조성에서 크게 나타났으며 0.60PZN-0.15BZN-0.25PT 시편의 경우 각각 58.5%, 120.5, 150x$10^{-12}$[C/N]의 값을 나타내었다.다.다.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.3
• /
• pp.253-260
• /
• 1992

In this study, the dielectric, structural and electrical properties of Pb(ZnS11/3TNbS12/3T)OS13T-BaTiOS13T-PbTiOS13T system ceramics were investigated with respect to the variation of YS12TOS13T addition amount. As the YS12TOS13T addition amount is increased, the resistivity at 100$^{\circ}C$ and the resonant/antiresonant frequencies and the frequency constant are slowly increased, and the grain growth is restrained until 0.4 wt% YS12TOS13T addition amount but continuously increased with the addition amount more than 0.4 wt% YS12TOS13T. As the YS12TOS13T addition amount is increased, the density, the diffuseness of dielectric constant and the induced polarization are increased until 0.4 wt% YS12TOS13T addition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.303-304
• /
• 2005

Add $Li_2CO_3$ to $(Ba_{0.6}Sr_{0.4})$ $TiO_3$ powder to lower sitering temperature in this research, made thick film by tape casting method. Investigated about sitering temperature and physical properties that added $Li_2CO_3$ Even if lower sitering temperature about $200^{\circ}C$ adding $Li_2CO_3$ 10wt.%, density was near to 5.7$g/cm^3$ that is theoretical values, and crystal structure examined as perobeuseukaiteu senior after sintering.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.304-304
• /
• 2010

최근 생활에 편리하며 휴대하기 좋은 전자기기들이 개발되고 있다. 휴대폰이나 MP3와 같은 전자기기들은 거의 필수품이라고 할 정도로 우리의 일상생활에 근접하여 있다. 그 종 대표적으로 휴대폰의 종류로 스마트폰과 같은 터치스크린을 이용한 사례는 점차 상승하고 있으며 시간이 지날수록 그 수요는 더욱 많아지고 있다. 때문에 몰입감 제공을 위하여 햅틱장치의 채용이 일반화 되고 있다. 햅틱장치란 가상환경이나 원거리에 있는 환경과 사용자가 상호 작용할 때 사용자에게 촉감이나 힘의 정보를 전달하여 주는 장치로 진동 및 회동 저항에 의해 사용자로 하여금 촉감들 느낄 수 있도록 하는 장치를 뜻한다. 즉, 현실감을 전달을 중점으로 하는 햅틱장치는 빠른 응답 속도와, 진동의 주파수와 크기는 독립적으로 제어가 가능해야 하며 기계적 수용기들을 직접적으로 자극할 수 있어야 한다. 하지만 모바일 햅틱장치의 경우 크기 및 소비전력의 문제로 모든 스펙을 만족하기에는 어려워 좀 더 한정적인 느낌을 제공할 수 없다. 현재까지 모바일 장치에서 햅틱 피드백을 위하여 진동모터나, 솔레노이드, 압전 액츄에이터 등이 많이 사용되어 지고 있다. 그 중 압전 액츄에이터는 입력에너지를 기계적 출력에너지로 변환되는 효과를 이용 한 것으로 압력 센서, 초음파 센서 등 많은 분야에서 응용되고 있으며 변위 범위는 작지만, 크기가 매우 작고 변위 정밀도가 높으며 발생력과 응답속도가 빠르다는 장점이 존재한다. 이를 이용한 햅틱 압전 엑츄에이터의 제작에 사용되는 압전 세라믹스는 높은 전기적 특성을 가질수록 더 졸은 효율을 가지며 이로 인하여 보다 좋은 전기적 특성을 가지는 압전 세라믹스를 필요로 한다. 현재 많이 사용되는 PZT계 세라믹스는 우수한 전기적 특성으로 많이 사용되고 있지만 Pb의 유독성으로 인한 환경문제로 Pb가 포함된 제품을 제한하고 있어 현재 Lead-free의 연구가 이루어지고 있다. Lead-free중 Ba$(Ti_{0.8}Zr_{0.2})O_3$(BZT)는 PZT계 세라믹스를 대체할 차세대 압전 재료로 주목받고 있다. 일반적으로 Lead-free의 압전계수($d_{33}$=100~300pC/N)는 비교적 낮은 값을 보이지만 BZT의 압전계수(BZT $d_{33}$~620pC/N)는 PZT계 세라믹스의 압전계수($d_{33}$=500~600pC/N)와 비교하여 부족하지 않은 압전계수를 보여주며 PZT를 대체할 재료로 주목받고 있다. 본 실험은 햅틱 압전 엑츄에이터용 무연 압전세라믹스의 제작을 위하여 Ba$(Ti_{0.8}Zr_{0.2})O_3-(Ba_{0.7}Ca_{0.3})-TiO_3$(BZT -BCT)의 조성으로 유전 및 압전 특성을 조사하였다.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.8
• /
• pp.858-868
• /
• 1992

0.085Ba(LaS11/2TNbS11/2T)OS13T-0.915Pb(ZrS1yTTiS11-yT)OS13T (0.45$\leq$y$\leq$0.65) transparent electrooptic ceramics were fabricated by two-stage sintering method. The structural, ferroelectric and electrooptic properties were investigated varying composition and second sintering time. Also the possibility of application to electrooptic device was studied. If we increase the PbZrOS13T contents, dielectric constants were increased and Curie temperature was decreased. In the composition of 0.55[mol] PbZrOS13T, electromechanical coupling factor and piezoelectric charge constant were the highest values of 43[%] and 173x10S0-12T[C/N], respectively. Mechanical quality factors were decreased with the increasing PbZrOS13T contents. Light transmittance was increased with wavelength when measured from 300[nm] to 900[nm], and with PbZrOS13T contents in the range of 0.50[mol]-0.65[mol], and had the highest value of 67[%] in the composition of 0.65[mol] PbZrOS13T. From the results of ferroelectric hysteresis loop and transmitted light intensity with electric field, the specimens with compositions of 0.65,0.60,0.55[mol] PbZrOS13T were applicable to electrooptic memory device and those with compositions of 0.50,0.45[mol] PbZrOS13T were applicable to linear electrooptic device.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.31.1-31.1
• /
• 2009

In an approach to acclimate ourselves torecent ecological consciousness trend, a lead-free piezoelectric material, bismuth sodium titanate (abbreviated as BNT) based bismuth sodium barium titanate (abbreviated as BNT-BT), was considered as an environment-friendly alternative for a lead based piezoelectric system. Ceramic specimens of0.94[(BixNa0.5)TiO3]-0.06[BaTiO3] (x = 0.500~0.515) compositions were prepared by a modified mixed oxide method. To increase the chemical homogeneity andre action activity, high energy mechanical milling machine and pre-milled nanosized powder has been used. In this method (BixNa0.5)TiO3 (x=0.500~0.515) andBaTiO3 were prepared separately from pre-milled constituent materials at low calcination temperature and then separately prepared BNTX (X=1, 2, 3 and 4) and BT were mixed by high energy mechanical milling machine. Without further calcination step the mixed powders were pressed into disk shape and sintered at $1110^{\circ}C$. Microstructures, phase structures and electrical properties of the ceramic specimens were systematically investigated. Highly dense ceramic specimens with homogenous grains were prepared in spite of relatively low sintering temperature. Phase structures were not significantly influenced by the excess amount Bi. Large variation on the piezoelectric and dielectric properties was detected at relative high excess Bi amounts. When $x{\leq}0.505$, the specimens exhibit insignificant variation in piezoelectric and dielectric constant though depolarization temperature is found to be decreased. Considerable amount of decrease in piezoelectric and dielectric properties are observed with higher excess of Bi amounts ($x{\geq}0.505$). This research indicates the advantages of high energy mechanical milling and importance of proper maintenance of Bi stoichiometry.