• Journal of the Korean Institute of Gas
• /
• v.15 no.4
• /
• pp.33-38
• /
• 2011

The introduction of alternative fuels is beneficial to overcome the fuel shortage and reduce engine exhaust emissions. LPG and CNG are relatively clean fuel and considered as most promising alternative automotive fuels worldwide because of its emission reduction potential and lower fuel price compared to gasoline. Now a day’s adaptation of dual fuel approach is the growing as common trend. The two fuels can be successfully implemented with existing gasoline engine with little modification. The present study was done to analyze the performance and emissions analysis of a multi cylinder spark ignition engine fuelled with the benefits of CNG and LPG aseffective alternate automotive fuels by simply using them in an unmodified petrol engine. The test results indicate, the energy content of CNG and LPG is the most limiting factor in acceptance for fuel economy and performance reasons. Thermal efficiency was high for CNG lowest for gasoline and LPG between the two. BSFC, CO and HC were low and NOx was high for CNG and low for gasoline, LPG lies between the two.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.5-10
• /
• 2005

The effect of ultrasonic energy for diesel fuel and blend oil has been revealed in this paper. The experimental setup consisted of a high speed diesel engine with 4 cylinder, dynamometer and ultrasonic fuel feeding system. Ultrasonic energy was added to diesel fuel and blend oil, which is a blend of diesel fuel and rape-seed oil. As engine speed was changed, engine torque and power, brake specific fuel consumption and thermal efficiency were measured in detail. As the results, by adding ultrasonic energy to diesel fuel and blend oil, the engine performance was improved in range of the experiment. The effect of improvement on brake specific fuel consumption and thermal efficiency for blend oil is higher than that for diesel fuel. When ultrasonic energy was added to diesel fuel or blend oil, a rise in engine torque for diesel fuel was higher than that for blend oil, but the effect of ultrasonic energy was small. From these results, it may be desirable to add ultrasonic energy to blend oil for the use of blend oil to diesel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.9-15
• /
• 2006

Experiments are conducted to compare fuel economy of FTP-75 mode on two different lock-up conditions; (A) Lock-up on at engine speed of 1,200(rpm) and above for 3rd & 4th gear, (B) Lock-up on at engine speed of 1400rpm and above for 4th gear only. As a result, case A had better fuel economy about 2.75(%) than case B for FTP-75 mode. Simulation(CRUISE, AVL) study is also carried out in order to estimate the effect of Lock-up control strategy for vehicle fuel economy. The fuel economy simulation result agrees with the measured fuel economy within error of 2(%). The improved Lock-up control strategy is proposed by simulation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.188-194
• /
• 2005

The direct injection diesel engine is one of the most efficient thermal engines. For this reason DI diesel engines are widely used for heavy-duty applications. But the world is faced with very serious problems related to the air pollution due to the exhaust emissions of diesel engine. So, that is air pollution related to exhaust gas resulted from explosive combustion should be improved. Exhaust Gas Recirculation(EGR) is a proven method to reduce NOx emissions. In this study, the experiments were performed at various engine loads while the EGR rates were set from $0\%$ to $30\%.$ The emissions trade-off and combustion of diesel engine are investigated. The brake specific fuel consumption rate is very slightly fluctuated with EGR in the range of experimental conditions. The ignition delay increased with increasing EGR rate. The maximum value of premixed combustion for the rate of heat release is increased with increasing EGR rate. NOx emissions are decreased with increasing EGR rate at high load and high speed. It was found that the exhaust emissions with the EGR system resulted in a very large reduction in oxides of nitrogen at the expense of higher smoke emissions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5082-5088
• /
• 2015

In this paper, durability test of 1000cc level gasoline engine has been carried out. Durability test set total 300 hours and WOT condition. Engine torque, power, fuel consumption, blow-by gas flow rate, and oil pressure are measured to analyse performance variation by time. As a result, engine performance of high rpm range gradually reduced by time but for relatively low rpm range shows stable performance. Blow-by gas flow rate shows 0.4% of averaged induction air flow rate, which is excellent rate for 1000cc level gasoline engine. Engine torque and fuel consumption data show the break-in upto 100 hours and aging trend after that. After 300 hours, engine is disassembled and each part is checked for the damage or crack.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.153-158
• /
• 2006

To optimize the combustion system in a HSDI diesel engine, a new analysis technology was developed. The in-cylinder 3-D combustion analysis was carried out by the modified KIVA-3V, and the spray characteristics for the high pressure injection system were analyzed by HYDSIM. The combustion design parameters were optimized by coupling the KIVA-3V and the iSIGHT. The optimization procedure consists of 3 steps. The $1^{st}$ step is the sampling method by the Design of Experiment(DOE), the $2^{nd}$ step is the approximation using the Neural Network method, and the $3^{rd}$ step is the optimization using the Genetic Algorithm. The developed procedures have been approved as very effective and reliable, and the computational results agree well with the experimental data. The analysis results show that the optimized combustion system in a HSDI diesel engine is capable of reducing NOx and Soot emissions simultaneously keeping a same level of the fuel consumption(BSFC).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.106-112
• /
• 2008

Modern vehicles require a high degree of refinement, including good drive ability to meet customer demands. Vehicle drive ability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. This paper focuses on the simulation of FTP-75 mode which is considered with spark timing control on transient condition. The acceleration is the most important factor for vehicle fuel economy. The retard of spark timing increases in proportion to acceleration. Likewise, bsfc(break specific fuel consumption) which is affected by spark timing also increases in proportion to acceleration. The result of simulation considered transient condition shows 0.3% of error comparing with a test on chassis-dynamometer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.4
• /
• pp.481-489
• /
• 1998

The effects of recirculated exhaust gas on the characteristics of fuel economy combustion and exhaust emissions have been experimentally investigated by a four-cylinder four cycle indirect injection water-cooled and marine diesel engine operating at several loads and speeds. in order to reduce the soot contents in the recirculated exhaust gas to intake system of the engine a novel diesel soot removal system with a cylinder-type scrubber which has 6 water injectors(A water injector has 144 nozzles in 1.0 mm diameter) is specially designed and manufactured for the experiment system The experiments in this study are performed at the fixed fuel injection timing of $15.3^{\circ}$ BTDC regardless of experimental conditions, The brake specific fuel consumption rate is slightly fluctuated with EGR in the range of experimental conditions, The maximum value of premixed combustion for the rate of heat release is decreased with EGR at engine load 25% and the ignition is slightly delayed with EGR at engine load 100% NOx emissions are markedly decreased with EGR especially at high loads while soot emissions are increased as the EGR rate rises.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.120-127
• /
• 2005

An IDI diesel engine used to agricultural tractors was fueled with $20\%$ biodiesel fuel(BDF 20) in excess of 300 hours. Engine dynamometer testing was completed at regularly scheduled intervals to monitor the engine performance and exhaust emissions. The engine performance and exhaust emissions were sampled at 1 hour interval for analysis. The combustion variation such as the combustion maximum pressure and the crank angle at this maximum pressure was not appeared during long-time dynamometer testing. Also, BSFC with BDF 20 resulted in lower than with diesel fuel. Since the biodiesel fuel used in this study includes oxygen of about $11\%$, it could influence the combustion process strongly. So, BDF 20 resulted in lower emissions of carbon monoxide, carbon dioxide, and smoke emissions without special increase of oxides of nitrogen than diesel fuel. It was concluded that there was no unusual deterioration of the engine, or any unusual change in exhaust emissions from using the BDF 20.

• Journal of the Korean Society of Combustion
• /
• v.21 no.2
• /
• pp.1-6
• /
• 2016

To meet the Tier-4 emission standard, a variety of combustion technology in the field of off-road engine has been applied in conjunction with the engine after treatment technology. In this study, as the basis study for applying VGT and HPL EGR to 3.6 L CRDi engine, exhaust gas characteristics and fuel economy characteristics are confirmed in accordance with VGT and EGR operating conditions. Consequently, in the EGR applicable conditions, 60% VGT vane duty condition was confirmed that the trade-off characteristics between NOx and smoke are advantageous. In addition, in view of BSFC, VGT vane duty is considered desirable to control at around 50%.