• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.1
• /
• pp.42-48
• /
• 2011

In this paper, a passive load-pull using a GaN HEMT (Gallium Nitride High Electron Mobility Transistor) bare-chip in X-band is presented. To obtain operation conditions that characteristic change by self-heating was minimized, pulsed drain bias voltage and pulsed-RF signal is employed. An accuracy impedance matching circuits considered parasitic components such as wire-bonding effect at the boundary of the drain is accomplished through the use of a electro-magnetic simulation and a circuit simulation. The microstrip line length-tunable matching circuit is employed to adjust the impedance. The measured maximum output power and drain efficiency of the pulsed load-pull are 42.46 dBm and 58.7%, respectively, across the 8.5-9.2 GHz band.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.4
• /
• pp.440-450
• /
• 2003

Statement of problem : The joints of removable partial denture alloys have failed frequently after routine usage. Purpose : The purpose of this study was to evaluate the mechanical properties of the laser welded Co-Cr alloys. Material and method : For this study 20 Co-Cr specimens were casted and 10 of them were seperated on the middle area and laser welded with Alpha laser welding machine(Siro Lasertec, Pforzheim, Germany). Rest of them which were as cast, were used as a control group. For the section of the experimental specimens, wire cutting machine was used to make a even gap of the all specimens. Laser welding was done with manufacturer's instrunction and tested each specimen by Instron Machine. Tensile strength, 0.2% yield strength and % elongations were recorded. Fractured surfaces were investigated with SEM. Results : The results were as follows : 1. The tensile strength of the laser welded group(617.7MPa) was about 75% of the as cast group(820.4MPa). It had stastically significant differences(p<0.05). 2. The % elongation of the experimental group was 6.6 which was lower than the control group(14.3). 3. Fracture of the experimental group occured in the welded surface and showed many voids. In contrast, the fracture surface of the control group was showed rough surfaces without any voids. Conclusion : The tensile strengths of the as-cast joints were higher than those for the laser welded joints, and the % elongation of the experimental group was lower than the control group. Porosity was found in laser-welded joints.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.134-138
• /
• 2006

The isolation performance of the S-band single-pole single-throw(SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide(GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9 dB is obtained with the coplanar wire-bond interconnection(CWBI) at a 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion(IMD3) are less than 1.94 dB over $3.2{\sim}3.6\;GHz$ and greater than 64 dBc.

• Journal of Welding and Joining
• /
• v.33 no.4
• /
• pp.37-43
• /
• 2015

Characteristics of dissimilar metal welds between STS 316L and carbon steel ASTM A516 Gr.70 made with GTAW have been evaluated in terms of microstructure, ferrite content, chemical analysis, hardness and corrosion resistance. Three heat inputs of 9.00, 11.25, 13.00kJ/cm were employed to make joints of dissimilar metals with ER309 wire. Based on microstructural examination, the amount of vermicular type of ${\delta}$-ferrite was increased with increasing heat input due to the increase of Creq/Nieq in the second layer of welds. Based on the EDX analysis of weld metals, Cr and Ni content in the 2nd layer increased while those content in the first layer of welds decreased with heat inputs. Cellular solidification mode in the 1st layer and dendritic solidification mode in the 2nd layer due to different cooling rates were prevailed, respectively. Heat affected zone which formed hard microstructure showed higher hardness than the weld metal. The salt spray test of dissimilar metals weld joints showed that the carbon steel surfaces only corroded. The weight loss rate due to corrosion increased up to 100hours but it decreased above 100 hours. There was little difference in the weight loss caused by corrosion regardless of heat inputs.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.3
• /
• pp.289-294
• /
• 2014

Industrial manipulators are usually heavy given the payloads they carry. Therefore, they require high-capacity servomotors and speed reducers, which leads to high costs. However, if manipulator weight could be compensated for using a counterbalance mechanism, the motors' and speed reducers' capacities could be minimized substantially. However, it is usually difficult to assure durability and reliability with the conventional wire-based counterbalance mechanism. Therefore, a more robust gear- and roller-based counterbalance mechanism is proposed in this study. A manipulator was developed using this mechanism; this manipulator maintains its performance even when using motors and reducers of lower capacities. The results of various simulations and experiments verified that the proposed mechanism provides the torque required to compensate for gravitational torque in any configuration and minimizes the torque required for supporting a large payload.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.126-129
• /
• 2007

Recently the use of wireless network increases according to it solves the hand-off and with path loss, pading, noise etc of wireless network the research for transmission error improvement is developed. TCP and SCTP of standard where it guarantees the reliability of wire network apply in wireless network the congestion control, flow control mechanism used it decreases the efficiency of data transfer throughputs. In this paper, It mixes SCTP and SNOOP for SCTP apply on wireless network, to improve BS(Basic Station) operation processes when the transmission error occurs in wireless network. BS send ZWP(Zero Window Probe) to MN(Mobile Node) when the transmission error occurs so, check path and status and update RWND and error status checked. It selects the new path, send ZWA(Zero Window Advertisement) to FH(Fixed Host) and the prevents call to congestion control or flow control and it does to make wait status standing. Continuously of data transfer after the connection of wireless network is stabilized, it make increase about 10% the transmission throughput of data.

• International Journal of Safety
• /
• v.11 no.2
• /
• pp.15-21
• /
• 2012

This paper is aimed to develop an electrical fire detection system (EFDS) which can analyze the possibility of electrical fire for overcurrent, leakage current and arc signals of panel board in traditional market shop. The EFDS adopted fuzzy logic and precursory data for overcurrent, leakage current and arc signals to evaluate the possibility of electrical fire. The signals are obtained directly from panel board in traditional market shops and fuzzy membership function is obtained from experiment, simulation, expert's advice. The overcurrent data is acquired by thermal data of normal and abnormal states (partial disconnection) on the insulated electrical wire, in accordance with the increase of the current signal, The leakage current data is obtained under various environments. The arc signal is acquisited by waveforms of instantaneous value in time domain and frequency band in frequency domain. The Fuzzy algorithm for DB of EFDS consists of fuzzification, inference engine by Mamdani's method and defuzzification by center of gravity method. In order to verify the performance and reliability of EFDS, it was applied to Jeon-Ju traditional market shops (90 shops) in Korea. Results show that EFDS in this paper is useful in alarming the fire case, which will prevent severe damage to human beings and properties, and reduce the electrical fires in a vulnerable area of electrical disaster.

• Journal of Korean Neurosurgical Society
• /
• v.48 no.1
• /
• pp.37-45
• /
• 2010

Objective : Craniovertebral junction (CVJ) consists of the occipital bone that surrounds the foramen magnum, the atlas and the axis vertebrae. The mortality and morbidity is high for irreducible CVJ lesion with cervico-medullary compression. In a clinical retrospective study, the authors reviewed clinical and radiographic results of occipitocervical fusion using a various methods in 32 patients with CVJ instability. Methods : Thirty-two CVJ lesions (18 male and 14 female) were treated in our department for 12 years. Instability resulted from trauma (14 cases), rheumatoid arthritis (8 cases), assimilation of atlas (4 cases), tumor (2 cases), basilar invagination (2 cases) and miscellaneous (2 cases). Thirty-two patients were internally fixed with 7 anterior and posterior decompression with occipitocervical fusion, 15 posterior decompression and occipitocervical fusion with wire-rod, 5 C1-2 transarticular screw fixation, and 5 C1 lateral mass-C2 transpedicular screw. Outcome (mean follow-up period, 38 months) was based on clinical and radiographic review. The clinical outcome was assessed by Japanese Orthopedic Association (JOA) score. Results : Nine neurologically intact patients remained same after surgery. Among 23 patients with cervical myelopathy, clinical improvement was noted in 18 cases (78.3%). One patient died 2 months after the surgery because of pneumonia and sepsis. Fusion was achieved in 27 patients (93%) at last follow-up. No patient developed evidence of new, recurrent, or progressive instability. Conclusion : The authors conclude that early occipitocervical fusion to be recommended in case of reducible CVJ lesion and the appropriate decompression and occipitocervical fusion are recommended in case of irreducible craniovertebral junction lesion.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2696-2698
• /
• 2004

Iontophoresis를 이용한 경피전달용 약물 패치를 제작하기 위해 고분자의 종류, 전류크기, 시간에 따른 약물방출 결과를 발표한다. 고분자 Hydroxy Propyl Methyl Cellulose(HPMC), Hydroxy Propyl Cellulose(HPC), Hydroxy Ethyl Cellulose(HEC)에 각각 국소마취제-Lidocaine을 넣어 시료를 제작하였다. 약물 방출은 Drug Delivery Cell(DDC)위에 Ag/AgCl 전극 (anode), Pt wire 전극(cathode)을 각각 설치하여 전압인가에 따른 이온 유동으로부터 시간에 따른 전압/전류변화 및 약물농도를 고찰하였다. 전압 15V 인가 시 고분자 막과 전해질 사이에 흐르는 전류 1.0mA는 15분간 유지되지만, Ag/AgCl 전극의 산화작용으로 인해 전류는 서서히 감소하며 26분 후 거의 흐르지 않았다. 따라서 안정적인 전류로 유지되는 시간을 15분으로 최적화하였다. 고분자 중 HPMC 막을 사용하여 약물방출 실험을 한 경우 UV 분석결과 파장 262.26nm에서 최대 흡광도 0.238이었고, 가장 높은 약물농도가 나타났다. 이러한 HPMC의 약물방출 실험결과 비교적 높은 전류 1.0mA일 때 약물 방출량이 많았고, 동일한 전류 0.4mA를 장시간 흐르게 하였을 경우, 농도가 축적되므로 치료 가능한 안정적인 특성임을 확인하였다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.584-593
• /
• 2012

This paper introduces an AVP (Automated Valet Parking) system which applies an autonomous driving concept into the current PAS (Parking Assistant System). The present commercial PAS technology is limited into vehicle. It means vehicle only senses and controls by and for itself to assist the parking. Therefore, the present PAS is restricted to simple parking events. But AVP includes wider parking events and planning because it uses infra-sensor network as well as vehicle sensor. For the realization of AVP, the commercial steering system of a compact vehicle was modified into steer-by-wire structure and various sensors like LRF (Long Range Finder) and camera were installed in a parking area. And local & global server decides where and when the vehicle can go and park in the testing area after recognized the status of environment and vehicle from those sensors. GPS solution was used to validate the AVP performance. More various parking situations, vehicles and obstacles will be considered in the next research stages based on these results. And we expect this AVP solution with more intelligent vehicles can be applied in a big parking lot like a market, an amusement park, etc.