• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.4
• /
• pp.371-377
• /
• 2011

The aim of this study is to investigate the effects of aromatics and T90 temperature for high cetane number (CN) of diesel fuels on combustion and exhaust emissions in low-temperature diesel combustion in a 1.9 L common rail direct injection diesel engine at 1500 rpm and 2.6 bar BMEP. Four sets of fuels with CN 55, aromatic content of 20% or 45% (vol. %), and T90 temperature of $270^{\circ}C$ or $340^{\circ}C$ were tested. Given engine operating conditions, all the fuels showed the same tendency of decrease of PM with an increase of an ignition delay time. At the same ignition delay time, the fuels with high T90 produced higher PM. At the same MFB50% location the amount of NOx was similar for all the fuels. Furthermore, at the same ignition delay time the amounts of THC and CO were similar as well for all the fuels. The amount of THC and CO increased with an extension of the ignition delay time mainly because of the increase of fuel-air over-mixing.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1121-1126
• /
• 2010

This study is to investigate the effects of aromatics and T90 for low cetane number (CN) fuels on combustion and exhaust emissions in low-temperature diesel combustion. We use a 1.9-L common rail direct injection diesel engine at 1500 rpm and 2.6 bar BMEP. Low temperature diesel combustion was achieved via a high external EGR rate and strategic injection control. The tested fuels four sets: the aromatic content was 20% (A20) or 45% (A45) and the T90 temperature was $270^{\circ}C$ (T270) or $340^{\circ}C$ (T340) with CN 30. Given the engine operating conditions, the T90 was the stronger factor on the ignition delay time, resulting in a longer ignition delay time for higher T90 fuels. All the fuels produced nearly zero PM because of the extension of the ignition delay time induced by the low cetane number. The aromatic content was the main factor that affected the NOx and the NOx increased with the aromatic content.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.2
• /
• pp.252-258
• /
• 2009

Engine bench tests has been done on a common-rail diesel engine with bio-diesel fuel to study effects of B100 and B20 on output power, fuel consumption and emissions. Test results show that B100 and B20 could reduce PM, HC, CO emission and smoke, but power decrease, fuel consumption increase and NOx increase obviously, B100 reduce PM and DS with $50%{\sim}70%$ and $80%{\sim}85%$ compared with diesel fuel, while B20 reduce PM and DS with $25%{\sim}35%$ and $30%{\sim}40%$. NOx of B100 and B20 increase $5%{\sim}20%$ compare to diesel.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.26-35
• /
• 1990

This is an experimental study to investigate the characteristics of Diesel spray and Diesel engine performance using ultrasonic injection nozzle (A, B type) and conventional commercial injection nozzle (C type). The results are obtained as follows: 1. SMD and range of size distribution of Diesel spray using the ultrasonic nozzle are smaller than those using the conventional injection nozzle, and spray angle is spread. 2. Because of the difference of the ultrasonic vibration energy transfer in the same condition, the effects of A-type ultrasonic vibration are larger than those of B-type ultrasonic vibration. 3. Attaching the ultrasonic vibrator to the conventional injection nozzle of the Diesel engine, engine performances i.e. BMEP, BSFC, and cylinder peak pressure are improved.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.35-44
• /
• 2002

Engine cycle simulation using a two-zone model was performed to investigate the effect of the engine parameters on NO and soot emissions in a DI diesel engine. The present model was validated against measurements in terms of cylinder pressure, BMEP, NO emission data with a 2902cc turbocharger/intercooler DI diesel engine. Calculations were made for a wide range of the engine parameters, such as injection timing, ignition delay, Intake air pressure, inlet air temperature, compression ratio, EGR. This parametric study indicated that NO and soot emissions were effectively decreased by increasing intake air pressure, decreasing inlet air temperature and increasing compression ratio. By retarding injection timing, increasing ignition delay and applying EGR. NO emission was effectively reduced, but the soot emission was increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.7
• /
• pp.86-93
• /
• 1999

Turbocharger has been used to increase the performance of diesel engine, especially ship engine , for years. Recently, the turbocharger is being adopted not only for an agricultural engine but also for an automobile engine. To improve the performance of diesel engine , the problem of the reduction of A/F ratio in high speed should be solved. Turbocharger is well known for its cost effectiveness, reliability and duration . In this study, an experiment was conducted to verify simulation program . The results for natural aspiration engine and turbocharged engine were compared. In order to estimate the characteristics of exhaust gas, D-13 mode was selected. Power, torque and BSFC of turbocharged engine were increased than those of natural aspiration engine by about 48%, 46% and 5%, respectively . The components in exhaust gas except NOx from turbocharger engine were less than the amount set up for 2000-year regulation.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.2
• /
• pp.155-163
• /
• 1999

In this study, single cylinder engines with different tumble ratio were made to find out in-cylinder fluid motion and flame propagation. Tumble ratio derived from the steady state flow rig test. Flame propagation speed was obtained using cylinder head gasket ionization probe and the piston ionization probe. And the combustion pressure in cylinder was measured to analyze the combustion characteristics. In case of high tumble engine, BSFC and BSHC were decreased and BSNOx was increased at part load test. Also BMEP and combustion peak pressure was increased at full load test. Tumble flow motion had an great effects on initial burning period rather than main burning period in part load test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.31-35
• /
• 2004

A new combustion strategy called LIFC(Late Injection ＆ Fast Combustion) was developed for simultaneous reduction of particulate matter(PM) and nitrogen oxides(NOx) in exhaust emission of diesel engines, In this study, effects of injection timing and injection pressure under relatively high EGR rate were investigated. The experiments were conducted in a conventional engine over a range of commercial engine speed. The test engine could be operated in LIFC up to 2000rpm / bmep 5 bar condition with significant reduction of NOx and PM. The experimental results showed potential for the mechanism of the simultaneous reduction of NOx and PM from HSDI diesel engines.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.73-79
• /
• 2002

The NO emissions at the exhaust manifo1d were investigated with a fast NO analyzer to investigate the cycle-by-cycle variations on NO emissions level and the dependence of NO emissions on combustion. The measurement was performed with a part load condition with respect to the mixture ratios and the changes in loads at 1800rpm. The averaged values were obtained during 200 cycles. We found that there is characteristic pattern in 70 emissions from exhaust port and it was possible to set a representative value with the data sampled during specific period. As the load increased, the characteristics of NO emissions were more dependent on combustion pressures. It was also analyzed that the correlation between combustion pressures and NO emissions for different equivalence ratios tends to increase as the mixture goes leaner, Furthermore, this correlation for the lean mixture near the lean limit seemed to be kept.

• Journal of ILASS-Korea
• /
• v.22 no.4
• /
• pp.203-209
• /
• 2017

The International maritime organization(IMO), in an effort to slow down the global warming, proposes reduction in ship's speed as a way to lower the rate emissions from ships. In addition, since ship's fuel cost have been increased, the shipping volumes, fuel-saving technology are being required urgently. Therefore, in this present study, a method of reducing the fuel cost that can improve the performance of the diesel engine was tried by introducing a predetermined amount (0.1~0.3% of the mass amount of fuel used) of hydrogen fuel additive. The experimental conditions of the test engine were 1500rpm and torque BMEP-10b ar. The engine performances (power output, fuel consumption rate, p-max, exhaust temperature) were compared before and after addition of hydrogen fuel additives. This experimental study confirmed reducing at least 2% fuel consumption and 2.19% NOx emission.