• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.119-126
• /
• 2004

BLDC Motor is one of the widely utilizable motors in servo system. The accurate calculation of the power loss for the IGBT and Inverse diode with Bipolar and Unipolar switching modes the driving modes is important for the design of drives for their heat treatment. If it were not for temperature-sensors in devices, it is difficult to get direct power loss, so. Power losses may be modeled by computer modeling to obtain the Calculation of the Power loss for Inverter in BLDC Motor with switching modes which is presented in this paper. The computer modeling is carried out by Matlab simulation. The power loss consists of conduction losses Conduction losses are the source of occurrence due to The IGBT and Inverse diode currents. Switching losses are the source of occurrence due to switching on/off in the devices, and gives the dominant influence to the loss. As a result, the unipolar I mode is best in reducing the heat losses.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.3
• /
• pp.221-228
• /
• 2008

In the 2-phase excited BLDC motor drives using a unipolar PWM scheme, there exists, in some cases, a unwanted leakage current which flows through the anti -parallel diode in the non-excited phase leg of the inverter. In this paper the cases in which the leakage current exists and the influence of the leakage current are analyzed, and a novel unipolar PWM scheme which can eliminate the leakage current is proposed. The leakage current increases as the motor speed is increased or PWM duty is decreased, and as a result the output power of the motor is reduced considerably. The effectiveness of the proposed unipolar PWM scheme isverified through the comparative simulations and experiments.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.3
• /
• pp.405-412
• /
• 2023

With the development of drone and ICT convergence technology, the use of underwater drones such as leisure underwater drones such as underwater exploration for fishing and industrial drones such as bridge piers is increasing. Existing motor controllers are suitable for aerial drones and these can increase the completeness of underwater drones and their reliability in motor control by developing BLDC motor controllers dedicated to underwater drones. By developing a battery management system (BMS) exclusively for underwater drones, battery stability was ensured by checking the state of charge, checking the state of discharge, adjusting cell balancing, and implementing high/voltage protection functions.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.170-172
• /
• 2003

Among low power servo applications, classical DC motors are very popular because they are reasonably cheap and easy to control. The main disadvantage is the mechanical collector which has only a limited life period. Also, brush sparking can destroy the rotor coil, generate EMC problems. So permanent magnet brushless do motors and drives are being used increasingly in a wide range of applications. This has been made possible with the advantages of high performance permanent magnets with high coercively and residual magnetic, which make it possible for the PM to have superior power density, torque to inertia ratio and efficiency, when compared to an induction or conventional dc machine. This paper presents the design of a PM brushless dc motor drive simplistically operates as a classical dc motor. The BLDC motor drive system for this paper composes to the power integrated circuits, the one chip device. And several simple semiconductors add to drive system for a motor drive system simplistically operates as a conventional dc motor. Test results confirmed the feasibility of the proposed motor drive system design.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.2
• /
• pp.255-265
• /
• 2009

This paper presents the acoustic noise and mechanical vibration reduction of a coreless brushless DC motor with an air dynamic bearing used in a digital lightening processor. The coreless brushless DC motor does not have a stator yoke or stator slot to remove the unbalanced force caused by the interaction between the stator yoke and the rotor magnet. An unbalanced force makes slotless brushless DC motors vibrate and mechanically noisy, and the attractive force between the magnet and the stator yoke increases power consumption. Also, when a coreless brushless DC motor is driven by a $120^{\circ}$ conduction type inverter, high frequency acoustic noise occurs because of the peak components of the phase currents caused by small phase inductance and large phase resistance. In this paper, a core-less brushless DC motor with an air dynamic bearing to remove mechanical vibration and to reduce power consumption is applied to a digital lightening processor. A $180^{\circ}$ conduction type inverter drives it to reduce high frequency acoustic noise. The applied methods are simulated and tested using a manufactured prototype motor with an air dynamic bearing. The experimental results show that a coreless brushless DC motor has characteristics of low power consumption, low mechanical vibration, and low high frequency acoustic noise.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.869-873
• /
• 2008

Optimization method for the open loop commutation time intervals in HDD spindle start-up control is presented in this paper. A hard disk drive(HDD) uses a sensorless brushless DC motor(BLDC) for the platter rotation. Because there is no direct sensor for the rotor position, open loop commutations after sensing the rotor position at a standstill using inductive sensing method are performed to speed up the rotor up to a certain speed where the zero crossings of the back electromotive force(EMF) are measurable. Therefore successful open loop commutations are necessary for the stable start-up control of the spindle motors. Random neighborhood search(RNS) algorithm is introduced as a optimization technic in this paper. Rotor speed and its standard deviation are used as a cost function and commutation intervals obtained from the spindle motion equation are used as initial parameter values for the RNS. With the help of the proposed method optimized open loop commutation time intervals for the very low start-up current are acquired and tested. The experimental results shows that the proposed method can decrease the start-up failure rate of a HDD spindle motor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.143-147
• /
• 2005

In this paper, an axial type brushless DC motor which has double rotors using rare-earth magnet pieces is designed. This kind of motor has shorter axial length and is easier to assemble than the radial type motors. To get enough torque, NdFeB magnet is used and for the cost of production, the magnets are segmented to rectangle or disk shape. To design this motor, a equivalent circuit is adopted and the air-gap density is calculated using 3D finite element method to get exact parameters. The design variables are optimized with genetic algorithm. From the results of the simulations, the reference of the axial type BLDC motors can be obtained.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.4
• /
• pp.477-487
• /
• 2008

This paper proposes a new position sensorless drive for brushless DC (BLDC) motors. Typical sensorless control methods such as the scheme with the back-EMF detection method show high performance only at a high speed range because the magnitude of the back-EMF is dependent upon the rotor speed. This paper presents a new solution that estimates the rotor position by using an unknown input observer over a full speed range. In the proposed method, a trapezoidal back-EMF is modelled as an unknown input and the proposed unknown input observer estimating a line-to-line back-EMF in real time makes it possible to detect the rotor position. In particular, this observer has high performance at a low speed range in that the information of a rotor position is calculated independently of the rotor speed without an additional circuit or complicated operation process. Simulations and experiments have been carried out for the verification of the proposed control scheme.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.106-114
• /
• 1998

Cogging torque is often a principal source of vibration and control difficulty in permanent magnet motors, especially at low speeds and loads. For example, reduction of cogging torque is an important specification for DC motors used for electric power stee- ring. This paper examines two motor design techniques, stator tooth notching and rotor pole skewing with magnet pole shaping, for reduction of cogging torque, and the effect of each method on the airgap flux, and the use of the Maxwell stress method and Fourier decomposition to calculate the periodic cogging torque. The analyses show that the cogging torque can be nearly eliminated by the suggested designs, with minimal scacrifice of output torque.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.6
• /
• pp.39-46
• /
• 2010

Linear induction motor is adopted as an actuator of the planar stage. An inherently poor characteristic at zero or ultra-low speed zone of the induction motor is remarkably improved due to a recent development of power electronic semiconductor technology and a spatial vector control theory. At present, a servo response speed of the induction motor reaches 90 percent of one of PM synchronous or BLDC motor. Specially, as a secondary of the induction motor can be constructed using uniform conducting sheets, there is no periodic force ripple as in PM motors. So, the induction motor can be superior to another driving means under a certain condition. This paper discusses the overall development procedure of non-contact planar stage with a big workspace using linear induction motors.