• Journal of Sensor Science and Technology
• /
• v.24 no.1
• /
• pp.15-21
• /
• 2015

Transparent and conductive multilayer thin films consisting of three alternating layers FZTO/Ag/$WO_3$ have been fabricated by radio-frequency (RF) sputtering for the applications as transparent conducting oxides and the structural and optical properties of the resulting films were carefully studied. The single layer fluorine doped zinc tin oxide (FZTO) and tungsten oxide ($WO_3$) films grown at room temperature are found to have an amorphous structure. Multilayer structured electrode with a few nm Ag layer embedded in FZTO/Ag/$WO_3$ (FAW) was fabricated and showed the optical transmittance of 87.60 % in the visible range (${\lambda}=380{\sim}770nm$), quite low electrical resistivity of ${\sim}10^{-5}{\Omega}cm$ and the corresponding figure of merit ($T^{10}/R_s$) is equivalent to $3.0{\times}10^{-2}{\Omega}^{-1}$. The resultant power conversion efficiency of 2.50% of the multilayer based OPV is lower than that of the reference commercial ITO. Asymmetric D/M/D multilayer is a promising transparent conducting electrode material due to its low resistivity, high transmittance, low temperature deposition and low cost components.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.73-73
• /
• 2011

We will report a few methods to improve the efficiency and stability in small molecule based organic solar cells, including the formation of bulk heterojunctions (BHJs) through alternative thermal deposition (ATD), the use of a micro-cavity structure and interface modifications. By ATD which is a simple modification of conventional thermal evaporation, the thicknesses of alternative donor and acceptor layers were precisely controlled down to 0.1 nm, which is critical to form BHJs. The formation of a BHJ in copper(II) phthalocyanine (CuPc) and fullerene (C60) systems was confirmed by AFM, GISAXS and absorption measurements. From analysis of the data, we found that the CuPc|C60 films fabricated by ATD were composed of the nanometer sized disk shaped CuPc nano grains and aggregated C60, which explains the phase separation of CuPc and C60. On the other hand, the co-deposited CuPc:C60 films did not show the existence of separated CuPc nano grains in the CuPc:C60 matrix. The OPV cells fabricated using the ATD method showed significantly enhanced power conversion efficiency compared to the co-deposited OPV cells under a same composition [1]. We will also present by numerical simulation that adoption of microcavity structure in the planar heterojunction can improve the short circuit current in single and tandem OSCs [2]. Interface modifications also allowed us to achieve high efficiency and high stability OSCs.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.9
• /
• pp.3061-3070
• /
• 2012

Novel 2-hexylthieno[3,2-b]thiophene-containing conjugated molecules have been synthesized via a reduction reaction using tin chloride in an acidic medium. They exhibited good solubility in common organic solvents and good self-film and crystal-forming properties. The single-crystalline objects were fabricated by a solvent slow diffusion process and then were employed for fabricating field-effect transistors (FETs) along with thinfilm transistors (TFTs). TFTs made of 5 and 6 exhibited carrier mobility as high as 0.10-0.15 $cm^2V^{-1}s^{-1}$. The single-crystal-based FET made of 6 showed 0.70 $cm^2V^{-1}s^{-1}$ which was relatively higher than that of the 5-based FET (${\mu}=0.23cm^2V^{-1}s^{-1}$). In addition, we fabricated organic photovoltaic (OPV) cells with new 2-hexylthieno [3,2-b]thiophene-containing conjugated molecules and methanofullerene [6,6]-phenyl C61-butyric acid methyl ester ($PC_{61}BM$) without thermal annealing. The ternary system for a bulk heterojunction (BHJ) OPV cell was elaborated using $PC_{61}BM$ and two p-type conjugated molecules such as 5 and 7 for modulating the molecular energy levels. As a result, the OPV cell containing 5, 7, and $PC_{61}BM$ had improved results with an open-circuit voltage of 0.90 V, a short-circuit current density of 2.83 $mA/cm^2$, and a fill factor of 0.31, offering an overall power conversion efficiency (PCE) of 0.78%, which was larger than those of the devices made of only molecule 5 (${\eta}$~0.67%) or 7 (${\eta}$~0.46%) with $PC_{61}BM$ under identical weight compositions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.154.2-154.2
• /
• 2016

In this work, we introduce a solution-processed CdS interlayer for use in inverted bulk heterojunction (BHJ) solar cells, and compare this material to a series of standard organic and inorganic cathode interlayers. Different combinations of solution-processed CdS, ZnO and conjugated polyelectrolyte (CPE) layers were compared as cathode interlayers on ITO substrates to construct inverted solar cells based on $PTB7:PC_{71}BM$ and a $P3HT:PC_{61}BM$ as photoactive layers. Introduction of a CdS interlayer significantly improved the power conversion efficiency (PCE) of inverted $PTB7:PC_{71}BM$ devices from 2.0% to 4.9%, however, this efficiency was still fairly low compared to benchmark ZnO or CPE interlayers due to a low open circuit voltage ($V_{OC}$), stemming from the deep conduction band energy of CdS. The $V_{OC}$ was greatly improved by introducing an interfacial dipole (CPE) layer on top of the CdS layer, yielding outstanding diode characteristics and a PCE of 6.8%. The best performing interlayer, however, was a single CPE layer alone, which yielded a $V_{OC}$ of 0.727 V, a FF of 63.2%, and a PCE of 7.89%. Using $P3HT:PC_{61}BM$ as an active layer, similar trends were observed. Solar cells without the cathode interlayer yielded a PCE of 0.46% with a poor $V_{OC}$ of 0.197 V and FF of 34.3%. In contrast, the use of hybrid ZnO/CPE layer as the cathode interlayer considerably improved the $V_{OC}$ of 0.599 V and FF of 53.3%, resulting the PCE of 2.99%. Our results indicate that the CdS layer yields excellent diode characteristics, however, performs slightly worse than benchmark ZnO and CPE layers in solar cell devices due to parasitic absorption below 550 nm. These results suggest that the hybrid inorganic/organic interlayer materials are promising candidates as cathode interlayers for high efficiency inverted solar cells through the modification of interface contacts.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.151-151
• /
• 2013

무기물 기반, Si-based 태양전지에 비해 가볍고 저렴하다는 관점에서 유기태양전지에 대한 연구가 진행되고 있다. 유기태양전지는 Si-based 태양전지에 비해 그 효율이 낮다는 점이 문제로 제기되어 왔지만, 억셉터와 도너의 nanocomposite 구조인 bulk-heterojunction (BHJ) 구조가 개발이 되면서 유기물의 짧은 엑시톤(exciton) 거리를 극복할 수 있게 되어 그 효율이 비약적으로 증가되는 결과를 낳았다. 또한 넓은 범위의 파장을 흡수 할 수 있는 작은 band-gap을 갖는 물질이 개발됨으로써 유기 태양전지의 효율은 점차 증가하고 있다. 최근에는 독일 회사인 Heliatek에서 12%가 넘는 유기태양전지를 발표함으로써 유기태양전지가 Si-based 태양전지를 대체할 수 있는 차세대 에너지 공급원으로의 가능성을 충분히 보였다. 이런 유기 태양전지는 하부 투명전극인 인듐주석산화물(ITO)/정공이동층(PEDOT:PSS)/광흡수층/전자이동층(LiF)/낮은 일함수를 갖는 상부전극인 Al 구조의 일반적인 구조; ITO/전자이동층/광흡수층/정공이동층/높은 일함수를 갖는 상부전극(Ag), 전하의 이동방향이 반대인 역구조 태양전지, 두 가지로 분류할 수 있다. 하지만 소자 안정성의 관점에서 일반적인 구조의 태양전지는 ITO/PEDOT:PSS 계면에서의 화학적 불안정성과, 낮을 일함수를 갖는 상부전극이 쉽게 산화되는 등의 문제가 있어 상부전극으로 높은 일함수를 갖는 전극을 사용하는 역구조 태양전지가 더 유리하다. 이러한 역구조 태양전지에서 효율을 높일 수 있는 요인 중 하나는 전자이동층에 있다. 광흡수층에서 형성되어 분리된 전자가 전극으로 이동하기위해서는 전자이동층을 거쳐야 한다. 하지만 이 전자이동층 내에서의 전자 이동속도가 느리다면, 즉 저항이 크다면 광흡수증과의 계면에서 Back electron trasnfer현상으로 재결합이 일어나게 되어 전극으로 도달하는 전자의 양이 줄어들게 되고, 이는 유기태양전지 효율을 낮추는 요인이 된다. 전자이동층 자체의 저항뿐만 아니라, 전자이동층의 표면 거칠기(morphology) 또한 유기 태양전지의 효율을 좌우하는 요인 중 하나이다. 광흡수층과 전자이동층의 계면에서 전자의 이동이 일어나는데, 전자이동층의 표면 거칠기가 크게되면 그 위에 박막으로 형성되는 광흡수층과의 계면저항이 증가하게 되고, 이는 광흡수층에서 전자이동층으로의 원활한 전자이동을 저해함으로써 소자 효율의 감소를 일으키게 된다. 따라서 우리는 전자이동층인 ZnO 박막의 스퍼터링 조건을 변화시킴으로써 ZnO 층의 두께에 따른 광투과도, 전기전도성 변화 및 유기태양전지의 효율변화와, 표면 거칠기에 따른 광변환 효율 변화를 관찰하고자 한다.