• Progress in Superconductivity and Cryogenics
• /
• v.25 no.3
• /
• pp.28-33
• /
• 2023

Magnetic relaxation properties of pure MgB₂ powder samples and diluted water-treated MgB₂ powder samples were investigated. The magnetic field H-dependence, m(H), and the time t-dependence, m(t), of the magnetic moment m were measured and analyzed using the PPMS-VSM magnetometer equipment, respectively. The m(t) reduction rates of pure MgB₂ powder samples and diluted water-treated MgB₂ powder samples decreased to about 0.7 ~ 1.8% and 0.6 ~ 1.0% for about 7200 s, respectively, at temperature T = 15 K. The magnetic relaxation properties of the two types of MgB₂ powders were analyzed by calculating the magnetic relaxation rate S = -dln(M_irr)/dln(t) values according to Anderson-Kim theory. The magnetic relaxation ratio S values of the two types of MgB₂ powder samples were almost similar. As a result of the quantum creep effect, the constant magnetic relaxation rate S characteristic was confirmed at a temperature range of T = 10 K or less.

• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.105-110
• /
• 2011

SQUID sensor-based ultra low-field magnetic resonance apparatus with ${\mu}T$-level measurement field requires a strong prepolarization magnetic field ($B_p$) to magnetize its sample and obtain magnetic resonance signal with a high signal-to-noise ratio. This $B_p$ needs to be ramped down very quickly so that it does not interfere with signal acquisition which must take place before the sample magnetization relaxes off. A MOSFET switch-based $B_p$ coil driver has current ramp-down time ($t_{rd}$) that increases with $B_p$ current, which makes it unsuitable for driving high-field $B_p$ coil made of superconducting material. An energy cycling-type current driver has been developed for such a coil. This driver contains a storage capacitor inside a switch in IGBT-diode bridge configuration, which can manipulate how the capacitor is connected between the $B_p$ coil and its current source. The implemented circuit with 1.2 kV-tolerant devices was capable of driving 32 A current into a thick copper-wire solenoid $B_p$ coil with a 182 mm inner diameter, 0.23 H inductance, and 5.4 mT/A magnetic field-to-current ratio. The measured trd was 7.6 ms with a 160 ${\mu}F$ storage capacitor. trd was dependent only on the inductance of the coil and the capacitance of the driver capacitor. This driver is scalable to significantly higher current of superconducting $B_p$ coils without the $t_{rd}$ becoming unacceptably long with higher $B_p$ current.

• Korean Journal of Agricultural Science
• /
• v.48 no.1
• /
• pp.73-81
• /
• 2021

The current study investigated how Saccharomyces cerevisiae ameliorates the adverse effects of aflatoxin on in vitro rumen fermentation. In this study, five groups (T₁: Control [basal feed]; T₂: T₁ + 300 ppb aflatoxin B1 [AFB₁] and T₃, T₄, and T₅: T₂ with 0.05, 0.1, and 0.2% of S. cerevisiae, respectively) were prepared and incubated in vitro. The results revealed that truly degradable dry matter (TDDM), gas production (GP), microbial biomass production (MBP), truly degradable organic matter (TDOM), partitioning factor (PF), total volatile fatty acids (TVFA), acetate (A), propionate (P) and butyrate (B) values in the control group (T₁) were higher (p < 0.05) than those of the AFB₁ fed group (T₂). The A : P ratio in the control group (T₁) was reduced (p < 0.05) when compared to that of the T₂ group. The TDDM, TDOM, GP, TVFA, A, P, and B values of T₃, T₄, and T₅ improved with the increasing levels of S. cerevisiae; however, the values of group T₅ were lower (p < 0.05) than that of the control. The values of MBP, A : P ratio and PF in group T₅ were statistically similar to that of the control. It was concluded that the inclusion of S. cerevisiae (0.05 to 0.20%) to the AFB₁ (300 ppb) contaminated feed partially to completely ameliorated the adverse effects of AFB₁ on the in vitro rumen fermentation parameters.

• Clinical and Experimental Reproductive Medicine
• /
• v.16 no.2
• /
• pp.147-152
• /
• 1989

The purpose of this study is to detect certain change in peripheral blood lymphocyte subpopulations in women with premature ovarian failure. The B cells, T cells and subsets were counted in 21 women with premature ovarian failure and 30 age-matched normal control women. The B cells were measured by identifying lymphocyte with surface membrane immunoglobulin and T cells and subsets by indirect immunofluorescence technique with the monoclonal antibodies OK T3, OK T4, and OK T8. The results were as follows. 1. No significant difference in the absolute number of B cells, T cells and subsets between women with premature ovarian failure and normal control women was observed. 2. The percentage of B cells, T cells and OK T8(+) cells in women with premature ovarian failure was not significantly different from that in normal control subjects respectively. 3. The percentage of OK T4(+) cells and OK T4/0K T8(+) ratio was significantly higher in women with premature ovarian failure than in control subjects.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.274-280
• /
• 2008

The study of subjects were 8 persons. The study measured VO2max of each person and substituted METs at exercise intensity of both VO2max 50% and VO2max 70% in accordance with energy consumption formula to set exercise time at energy consumption of both 300kcal and 600kcal. And, the study substituted inclination and rate at exercise intensity that was measured at preliminary test. T, B, NK cell varied depending upon aerobic exercise to have no significant difference of exercise intensity at relative ratio of T, B, NK lymphocyte of all of lymphocytes and to have significant difference of Expenditures Calorie (p<.01) and interaction (p<.05) by T cell and Expenditures Calorie (p<.01) by B cell and Expenditures Calorie (p <.001) and interaction (p<.05) by NK cell.

• Analytical Science and Technology
• /
• v.23 no.5
• /
• pp.465-476
• /
• 2010

In this study, a number of volatile organic compounds (VOCs) including benzene, toluene, p-xylene, styrene, and methyl ethyl ketone were analyzed from samples collected in ambient air and under the field conditions. These samples were analyzed independently by two different set-ups for VOC analyses, i.e., between [1] gas chromatography/flame ionization detector with tube sampling - (F-T system) and [2] gas chromatography/mass spectrometer with bag sampling (M-B system). The analytical results derived by both systems showed fairly similar patterns in relative sense but with moderately large differences in absolute sense. The results of M-B system were high relative to F-T system with the F-T/M-B ratio below 1. If the relative biases of the two measurement techniques are derived in terms of percent difference (PD) in concentration values, the results were generally above 35% on average. A student t-test was applied to investigate the statistical significance of those differences between the systems. The results of both analytical systems were different at 95% confidence level for toluene, p-xylene, styrene, and methyl ethyl ketone (P < 0.043). However, F-T and M-B systems showed strong correlations for toluene and p-xylene. The observed bias is explained in large part by such factors as the differences in standard phases used for each system and the chemical loss inside the bag sampler.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.738-745
• /
• 2014

In this paper, It is performing to the elastic and elasto-plastic large deformation series analysis using a numerical method for the initial deflection effect of the aluminum alloy rectangular plate in the elasto-plastic loading area patch loading size. It is assumed a boundary condition to be a simply supported condition and consider the initial deflection amplitude, aspect ratio. It examined the critical elastic buckling load and post-buckling behaviour of aluminium alloy A6082-T6 rectangular plate. It used a commercial program for the elastic and elasto-plastic deformation series analysis. If the initial deflection amplitude is smaller, the in-plane rigidity with increasing to load is reduced from the start and occurs significantly more increasing the amplitude. More higher the aspect ratio, the initial yield strength is gradually decreased, and the plate thickness thicker and occurs larger than the thin walled plate a reduction ratio of the initial yield strength of the patch loading size as 0.5.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.3
• /
• pp.211-219
• /
• 2009

The purpose of the study described in this paper was to experimentally investigate branch squared T joints with cold formed hollow structural sections under the in plane moment in a Vierendeel Truss. The branch in the T joints was welded to the upper flange of the chord. The main experimental parameters were the ratio of the width to the thickness of the chord ($2{\gamma}$), with ${16.7{\leq}2{\gamma}{\leq}33.3}$, and the width ratio of the branch to the chord ($\beta$), with ${0.40{\leq}{\beta}{\leq}0.71}$. Nine specimens were tested and manufactured in joints under the in plane bending moment. Based on the results of the test, the in plane moment strength of the branch squared T joints was determined according to the bending deformation of the chord flange yielding, regardless of the ratio of the width to the thickness of the chord and the ratio of the width of the branch to the width of the chord. Also, the in plane moment strength of the branch squared T joints in the hollow structural sections can be defined as 1.5 times the moment load at M1%B the strength of the joints that governed the serviceability in the control group. Finally, the experimental results with the branch squared T joints show that the in lane moment strength of the joint increased as $2{\gamma}$ decreased and $\beta$ increased.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.3
• /
• pp.169-176
• /
• 2014

This paper presents the experimental results of behavior of square CFT columns with large the width-ro thickness ratio strengthened with carbon fiber reinforced polymers (CFRP) sheets subjected to concentrated axial loading. The main parameters were b/t ratio and the number of CFRP layers and 6 specimens were fabricated. The values of b/t were ranged from 60 to 100. From the tests, Maximum increase of 16% was also achieved in axial-load capacity with three transverse layered CFRP applied on four sides of steel tubes. The load capacity decreased up to 41% comparing with nominal load capacity of unstrengthened CFT column. However, for CFRP strengthened CFT, the load capacity decreased up to 32%. Finally, from the load-strain relationships, the local buckling occurred before yield point of steel tubes. Also, from the load-strain relationships, it was observed that local buckling were delayed on CFT columns by CFRP sheets retrofitting.

• Earthquakes and Structures
• /
• v.18 no.6
• /
• pp.677-689
• /
• 2020

A building structural system of moment resisting frame (MRF) with concrete filled steel tubular (CFST) columns and wide flange H beams, is one of the most conveniently constructed structural systems. However, there were few studies on evaluating seismic performance of full-scale CFST columns under high axial compression. In addition, some existing famous design codes propose various limits of width-to-thickness ratio (B/t) for steel tubes of the ductile CFST composite members. This study was intended to investigate the seismic behavior of CFST columns under high axial load compression. Four full-scale square CFST column specimens with a B/t of 42 were carried out that were subjected to horizontal cyclic-reversal loads combined with constantly light, medium and high axial loads and with a linearly varied axial load, respectively. Test results revealed that shear strength and deformation capacity of the columns significantly decreased when the axial compression exceeded 0.35 times the nominal compression strength of a CFST column, P₀. It was obvious that the higher the axial compression, the lower both the shear strength and deformation capacities were, and the earlier and faster the shear strength degradation occurred. It was found as well that higher axial compressions resulted in larger initial lateral stiffness and faster degradation of post-yield lateral stiffness. Meanwhile, the lower axial compressions led to better energy dissipation capacities with larger cumulative energy. Moreover, the study implied that under axial compressions greater than 0.35P₀, the CFST column specimens with B/t limits recommended by AISC 360 (2016), ACI 318 (2014), AIJ (2008) and EC4 (2004) codes do not provide ultimate interstory drift ratio of more than 3% radian, and only the limit in ACI 318 (2014) code satisfies this requirement when axial compression does not exceed 0.35P₀.