• Analytical Science and Technology
• /
• v.33 no.4
• /
• pp.186-196
• /
• 2020

A simple and rapid preconcentration method of actinide from seawater using Actinide resin was developed and tested with the seawater spiked with a known U and Th. The developed method of Actinide resin based on column chromatography is less time-consuming and requires less labor compared with a typical co-precipitation technique for preconcentration of actinides. U and Th, which are relatively weak-bonded with Actinide resin among actinides, were used to determine the optimum flow rate of seawater sample and evaluate the capacity of Actinide resin to concentrate actinides from seawater. A flow rate of 50 mL min^-1 was available with Actinide resin 2 mL (BV, bed volume). When 5 or 10 L of seawater containing U were loaded on Actinide resin (2 mL, BV) at 50 mL min^-1, the recovery of U was 93 % and 86 %, respectively. For extraction of actinides bound with Actinide resin, we compared three methods: solvent extraction, ashing-acid digestion, and ashing-microwave digestion. Ashing-microwave digestion method shows the best performance of which is the recovery of 100 % for U and 81 % for Th. For the preconcentration of actinides in 200 L of seawater, a typical coprecipitation method requires 2-3 days, but the developed method in this study is achieved the high recovery of actinides within 12 h.

• Journal of Korea Multimedia Society
• /
• v.7 no.3
• /
• pp.357-367
• /
• 2004

In VOD systems the number of channels available to a video server is limited since the number of channels, the video server can support, is determined by the communication bandwidth of the video server. Multicast techniques such as batching, patching and batch-patching have been proposed to reduce I/O demand on the video server by sharing multicast data. In this paper, we propose a channel reservation batch-patching technique that first applies the batching technique to hot video requests and then applies the patching technique to the batches of the hot video requests. And the proposed technique reserves a part of the channel capacity of the video server for many hot video requests, so that the hot video requests can be served without defection. The performance of the proposed technique is compared with those of Patching and Batch-Patching techniques in terms of average service latency, defection rate, fairness and frame reduction rate by simulations.

• Structural Engineering and Mechanics
• /
• v.61 no.2
• /
• pp.245-253
• /
• 2017

The increasing lack of good quality soils allowing the development of roadway, motorway, or railway networks, as well as large scale industrial facilities, necessitates the use of reinforcement techniques. Their aim is the improvement of the global performance of compressible soils, both in terms of settlement reduction and increase of the load bearing capacity. Among the various available techniques, the improvement of soils by incorporating vertical stiff piles appears to be a particularly appropriate solution, since it is easy to implement and does not require any substitution of significant soft soil volumes. The technique consists in driving a group of regularly spaced piles through a soft soil layer down to an underlying competent substratum. The surface load being thus transferred to this substratum by means of those reinforcing piles, which illustrates the case of a piled embankment. The differential settlements at the base of the embankment between the soft soil and the stiff piles lead to an "arching effect" in the embankment due to shearing mechanisms. This effect, which can be accentuated by the use of large pile caps, allows partial load transfer onto the pile, as well as surface settlement reduction, thus ensuring that the surface structure works properly. A technique for producing rigid piles has been developed to achieve in a single operation a rigid circular pile associated with a cone shaped head reversed on the place of a rigid circular pile. This technique has been used with success in a pile-supported road near Bourgoin-Jallieu (France). In this article, a numerical study based on this real case is proposed to highlight the functioning mode of this new technique in the case of industrial slabs.

• Journal of Yeungnam Medical Science
• /
• v.20 no.2
• /
• pp.169-176
• /
• 2003

Background: Although dental implantation has become widespread and acceptable treatment for dental prosthodontics, maxillary posterior jaw region is often complicated by the pneumatization of the maxillary sinus and physiological resorption of the alveolar bone. When this occurs, the residual bone between the floor of the sinus and the crestal ridge is inadequate for the placement of implants. The sinus elevation procedure provides a way to increase the amount of available bone and to allow the placement of longer implants. Materials & methods: We studied 11 patients requiring the implant placements and the maxillary sinus elevation simultaneously from 1996 to 2003 in our clinic. Nine patients were males and two patients were females, aged from 39 to 72(mean=51.6). Four patients had medical compromised states; angina pectoris, diabetes, hypertension, hepatitis. Patients didn't show any pathologic findings clinically or radiographically. We studied the success and survival rate of implants, factors increasing the osseointegrating capacity of implants. Results: The success rate of osseointegration of implants was 93%. At least 6 months after loading on implants, the survival rate of implants was 78.5%. Autogenous bone graft and adequate residual bone height(>6mm) increased survival rate of implants. Conclusion: Successful implant placement with maxillary sinus elevation mainly depends on sufficient residual bone height, healthy maxillary sinus, autogenous bone graft.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.4
• /
• pp.684-692
• /
• 2016

Acute respiratory virus infectious diseases are a growing health problem, particularly among children and the elderly. Much effort has been made to develop probiotics that prevent influenza virus infections by enhancing innate immunity in the respiratory tract until vaccines are available. Lactobacillus plantarum GB-LP2, isolated from a traditional Korean fermented vegetable, has exhibited preventive effects on influenza virus infection in mice. To identify the molecular basis of this strain, we conducted a whole-genome assembly study. The single circular DNA chromosome of 3,284,304 bp was completely assembled and 3,250 protein-encoding genes were predicted. Evolutionarily accelerated genes related to the phenotypic trait of anti-infective activities for influenza virus were identified. These genes encode three integral membrane proteins, a teichoic acid export ATP-binding protein and a glucosamine - fructose-6-phosphate aminotransferase involved in host innate immunity, the nonspecific DNA-binding protein Dps, which protects bacteria from oxidative damage, and the response regulator of the three-component quorum-sensing regulatory system, which is related to the capacity of adhesion to the surface of the respiratory tract and competition with pathogens. This is the first study to identify the genetic backgrounds of the antiviral activity in L. plantarum strains. These findings provide insight into the anti-infective activities of L. plantarum and the development of preventive probiotics.

• Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.19-27
• /
• 2008

Simultaneous removal of ternary gases of $NH_3$, $H_2S$ and toluene in a contaminated air stream was investigated over 180 days in a biofilter. A commercially available inorganic/polymeric composite chip with a large void volume (bed porosity > 0.80) was used as a microbial support. Multiple microorganisms including Nitrosomonas and Nitrobactor for nitrogen removal, Thiobacillus thioparus (ATCC 23645) for $H_2S$ removal and Pseudomonas aeruginosa (ATCC 15692), Pseudomonas putida (ATCC 17484) and Pseudomonas putida (ATCC 23973) for toluene removal were used simultaneously. The empty bed residence time (EBRT) ranged from 60 - 120 seconds and the inlet feed concentration was $0.0325\;g/m^3-0.0651\;g/m^3$ for $NH_3$, $0.0636\;g/m^3-0.141\;g/m^3$ for $H_2S$, and $0.0918\;g/m^3-0.383\;g/m^3$ for toluene, respectively. The observed removal efficiency was 2% - 98% for $NH_3$, 2% - 100% for $H^2S$, and 2% - 80% for toluene, respectively. Maximum elimination capacity was about $2.7\;g/m^3$/hr for $NH_3$, > $6.4\;g/m^3$/hr for $H_2S$ and $4.0\;g/m^3$/hr for toluene, respectively. The inorganic/polymeric composite carrier required 40 - 80 days of wetting time for biofilm formation due to the hydrophobic nature of the carrier. Once the surface of the carrier was completely wetted, the microbial activity became stable. During the long-term operation, pressure drop was negligible because the void volume of the carrier was two times higher than the conventional packing materials.

• The Journal of the Korea Contents Association
• /
• v.9 no.11
• /
• pp.120-129
• /
• 2009

It is now the digital and multi-media era. The DVD market is growing constantly. So is the capacity and quality of DVD players, In our research, we focused on the younger generation, who are now the greatest consumers. The results helped signify the most distinctive and popularized DVD player designs that satisfy young people's entertainment needs. Our new design is a large step ahead of older ones. Previous designs were uniform and standard. This new design has distinctive features and is uniquely user-friendly. It is focused primarily on easy usability. The interface is simple and straight forward. The user can use the system easily before consulting a manual. It is consistent in internal and external software and hardware, allowing the user to easily adapt to the product. DVD players have become a necessity in the current multi-media/digital era. So products need to be geared towards being available to not just those who are technologically savvy, but also those who rely on basic user-intuition. Our design takes into account these conditions, based on our statistical research, allowing us to expect our product to be a competitive force in the DVD market.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.30 no.2
• /
• pp.100-106
• /
• 2018

Recently, the development of a heat pump technology to recover process waste heat and to generate steam of $120^{\circ}C$ or higher required for industrial processes, has attracted attention. The research of conventional heat pump utilizing the available energy is used primarily for air conditioning, and the production temperature is about $60^{\circ}C$, so it is difficult to utilize it for industrial use. Therefore, in this study, we developed a steam heat pump (SGHP) which recovers the waste heat of process and generates steam at $120^{\circ}C$. The low-pressure refrigerant R245fa, considered to be an eco-friendly refrigerant, has been selected as the refrigerant for SGHP in this study since its Ozone Depletion Potential (ODP) is zero and the Global Warming Potential (GWP) is relatively low. A flash tank functioning as a phase separator was installed in the rear stage of the condenser, and the saturated water of high temperature was decompressed to generate steam. It was started at the initial temperature of $70^{\circ}C$, and it was confirmed that $120^{\circ}C$ steam was produced after the system stabilized. We have conducted experiments by modifying the system, and ultimately achieved a heating capacity of 101.4 kW and a COP of 3.05.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.42 no.4
• /
• pp.183-193
• /
• 2019

Process mining is an analytical technique aimed at obtaining useful information about a process by extracting a process model from events log. However, most existing process models are deterministic because they do not include stochastic elements such as the occurrence probabilities or execution times of activities. Therefore, available information is limited, resulting in the limitations on analyzing and understanding the process. Furthermore, it is also important to develop an efficient methodology to discover the process model. Although genetic process mining algorithm is one of the methods that can handle data with noises, it has a limitation of large computation time when it is applied to data with large capacity. To resolve these issues, in this paper, we define a stochastic process tree and propose a tabu search-genetic process mining (TS-GPM) algorithm for a stochastic process tree. Specifically, we define a two-dimensional array as a chromosome to represent a stochastic process tree, fitness function, a procedure for generating stochastic process tree and a model trace as a string of activities generated from the process tree. Furthermore, by storing and comparing model traces with low fitness values in the tabu list, we can prevent duplicated searches for process trees with low fitness value being performed. In order to verify the performance of the proposed algorithm, we performed a numerical experiment by using two kinds of event log data used in the previous research. The results showed that the suggested TS-GPM algorithm outperformed the GPM algorithm in terms of fitness and computation time.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.2
• /
• pp.233-238
• /
• 2008

Recently, rainwater harvesting facilities have increasingly constructed mainly in elementary schools and government buildings. Nevertheless, few methods are available for efficient planning and design of rainwater harvesting facilities by considering the weather conditions and purpose of rainwater management in each site, which may lead to a construction of uneconomic facilities. The current method estimates the size of rainwater storage tank by multiplying the size of building or plottage with a certain ratio and has many limitations. In this study, we first developed a method for planning and design of rainwater storage facilities using $Rainstock^{TM}$ model, which is based on mass balance, and economic analysis. Then, the model was applied for the design of a rainwater harvesting facility in a building with the catchment area of $1,000m^2$. The model calculation indicated that the economic feasibility of rainwater harvesting depends on not only the size of storage tank but also the water usage rate. When the water usage rate is $1m^3/day$, the rainwater harvesting facility is not cost-effective regardless of the size of the storage tank. With increasing the water usage rate, the economical efficiency of the facility was improved for a specific size of the storage tank. Based on the model calculation, the optimum tank sizes for $5m^3/day$ and $10m^3/day$ of water usage rates were $24m^3$ and $57m^3$, respectively. It is expected that the model is useful for optimization of rainwater storage facilities in planning and designing steps.