• International Journal of Automotive Technology
• /
• v.7 no.7
• /
• pp.821-826
• /
• 2006

This paper describes a rollover index (RI)-based rollover mitigation control (RMC) system. A rollover index which indicates an impending rollover has been developed by a roll dynamics phase plane analysis. The rollover index is calculated using the roll angle, the roll rate, the lateral acceleration and time to wheel lift (TTWL). A differential braking control law based on a 2-D bicycle model has been designed using the direct yaw control (DYC) method. An RMC threshold has been determined from the rollover index. The performance of the RMC scheme and the effectiveness of the proposed rollover index are illustrated using a vehicle simulator.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.761-768
• /
• 1999

This paper presents an NVH test of Automotive power steering system performed at a half-car Test-rig. The test was done for neutral and full turn(or relief) conditions in steering wheel at a fixed rpm first, then followed by the same conditions for the rpm run-up. The sound intensity measurement verified the results from the frequency and order analysis, especially about the identification of major noise sources and their dominant frequencies. The results from thie study can be utilized in the system noise tuning when a new steering component is installed. In particular, the noise and vibration reduction at the relief condition will be accomplished through the knowledge obtained from this study and from the on-going research on the hose tuning techniques usign silencers and tuning cable inserted in the pressure hose.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.124-130
• /
• 2003

Many structural evaluation procedures of road and airfield pavements use the Falling Weight Deflectometer (FWD) as a critical element of non-destructive deflection testing. FWD is a trailer mounted device that provides accurate data on pavement response to dynamic wheel loads. A dynamic load is generated by dropping a mass from a variable height onto a loading plate. The magnitude of the load and the pavement deflection are measured by a load celt and geophones. And database concerning pavement damage should be enhanced to analyze loss of thickness asphalt layer caused from the plastic deformation of pavement structure, such as cracking or rutting. The prototype FWD is developed, which consists of chassis system, hydraulic loading system, data acquisition and analysis system. This system subsequently merged to from automation management system and is then validated and updated to produce a working FWD which can actually be used in the field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.214-219
• /
• 2003

This paper includes real-time tractive force estimation method using standard vehicle sensors such as wheel speed, brake pressure, throttle position, engine speed, and transmission carrier speed sensor. Engine map, torque converter lookup table, shaft torque observer, and brake gain adaptation method are used to estimate the tractive force. To verify this estimator, measurement which uses strain-based brake torque sensor and estimation results are presented. All results was performed using a real vehicle in a real-time.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.220-229
• /
• 2000

In the brake systems a proportioning valve which reduces the brake pressure at each wheel cylinder for anti-locking of rear wheels is closely related with the safety of vehicles. But, it is impossible for a present proportioning valve to exactly control brake pressure because mechanically it is an open loop control system. So, in this paper we describe a electronic brake pressure distribution system using a fuzzy controller in order to exactly control brake pressure using a close loop control system. The object of electronic brake pressure distribution system is to change an cut-in pressure and an valve slop of proportioning valve in order to obtain better good performance of brake system than with mechanical system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.177-183
• /
• 2004

The out-of-positioned small female drivers are most likely to be injured during airbag deployment due to their stature and proximity to the steering wheel and airbag module. In order to investigate the injury mechanisms, some experimental studies with Hybrid III 5% female dummy and with female cadavers could be found from the open literatures. However, the given information from those experimental studies is quite limited to the standard conditions and might not be enough to estimate the airbag inflation aggressiveness regarding on the occupant responses and injury. In this study, a finite element analysis has been performed in order to investigate the airbag-induced injuries. A finite element 5% female human model in anatomical details has been developed. The validation results of the model are also introduced in this paper.

• Journal of the korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.34-42
• /
• 1981

The feasibility of using fluidic components for improving certain performance characteristics of the suspension systems for tracked vehicle is investigated. This study describes three variable damping systems for which the damping coefficients are function of relative velocity and absolute a of the vehicle body. Through the comparison analysis between constant damping coefficient damper and each of variable dampers. the followings were found: (1)Fluidic Diode Damper gave less accelerations, (2)Both Fluidic Diode Damper and Relative Velocity Damper gave the less time for which the wheel is off the ground, (3) At low vehicle velocity Fluidic Diode Damper gave low energy dissipation rate, while at high vehicle velocity Turbulence Accelerometer Damper gave low energy dissipation rate.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.122-129
• /
• 2000

This paper describes a hybrid dynamic system(HDS) modeling method and result for the drivertrain of a parallel hybrid electric vehicle(PHEV) which consists of a gasoline engine, an electric machine, and a continuous variable transmission (CVT) and proposes a drivetrain control system. The control system has an engine controller, a motor controller, a CVT controller and a supervisory controller for the coordination of all system. The controller keep the speed of engine wheel and the output torque within the optimal operation range based on the experimental data. We also developed a MATLAB/SIMULINK program for the performance simulation of PHEV drivetrain model and controllers and compared the simulation result with the experiment result in the recent literatures.

• International Journal of Automotive Technology
• /
• v.5 no.2
• /
• pp.95-108
• /
• 2004

Lanekeeping assistance has the potential to save thousands of lives every year by preventing accidental road departure. This paper presents experimental validation of a potential field lanekeeping assistance system with quantitative performance guarantees. The lanekeeping system is implemented on a 1997 Corvette modified for steer-by-wire capability. With no mechanical connection between the hand wheel and road wheels the lanekeeping system can add steering inputs independently from the driver. Implementation of the lanekeeping system uses a novel combination of a multi-antenna Global Positioning System (GPS) and precision road maps. Preliminary experimental data shows that this control scheme performs extremely well for driver assistance and closely matches simulation results, verifying previous theoretical guarantees for safety. These results also motivate future work which will focus on interaction with the driver.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.56-62
• /
• 2007

In order to compare subjective and objective assessments, a passenger car was driven at several speeds over several road profiles. To measure the acceleration signals experienced by the seated subject who provided an subjective assessment, four triaxial translational accelerometers and one triaxial gyro sensor were mounted on the steering wheel and on the passenger seat and floor, respectively. Correlations were determined between the measured accelerations and the subjective assessments of 3 expert subjects and 9 general subjects using psychophysical power law.