• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1611-1612
• /
• 2006

We are using the Faraday's electromagnetic law so as to improve our life in various industry fields. However, the side effect of the Faraday's law can be occurredin the sensors of the vehicle due to the high current flow such as Ignition. This effect is mainly caused by the shape of the wiring harness between sensor and high current load in the vehicle. To minimize the side effect by Faraday's law, three methods shall be considered in this paper (1) Pin definition of the sensor, (2) Pin definition of the high current load, (3) Wiring harness shape.

• Journal of the Korean Institute of Gas
• /
• v.26 no.3
• /
• pp.54-59
• /
• 2022

This paper is a purpose to study and analyze the failure examples for timing belt, camshaft position sensor and ignition coil of LPG automotive engine. The first example, whe the service man install the front case bracket of engine, he excessively tightened up a 12mm bolt for being fixed of brackct. As a results, the bolt was separated from joint part so that it was put in between the crankshaft sprocket. Therefore the belt was broken off because of interference between timing belt and sprocket tooth. The second example, it verified the disharmony phenenomen of engine that the gap of the camshaft position sensor and camshaft senseing point assembled on cylinder head part was small more than iregular value so that the it was generated senseing damage phenomenon by pulse signal misconduct. The third example, it was found the engine disharmony phenomenon that the fire in the ignition coil was leaked by inner damage of Number 2 ignition coil.Therefore, the the manager of a car throughtly have to inspect not in order to arise the failure symptoms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2012

The brake-by-wire technology is a new automotive chassis system that allows standard braking operations by electronic components with lighter weights and faster response. The brake-by-wire units such as EMB (Electro-Mechanical Brake) are controlled by electronic sensors and actuators and, thus, the fault diagnosis is essential for implementation. In this study, a model-based fault diagnosis system is developed for the sensors based on the analytical redundancy method. The fault detection algorithm is verified in simulations for various faulty cases. A test bench is built including the EMB unit and the performance of the proposed fault diagnosis system is evaluated through the experiment.

• Environmental Engineering Research
• /
• v.20 no.4
• /
• pp.397-402
• /
• 2015

SCR has been popularly approved as one of the most effective means for NOx emission control in heavy-duty and medium-duty vehicles currently. However, high urea dosing would lead to ammonia slip. And $NH_3$ sensor for vehicle emission applications has not been popularly used in real applications. This paper presents experimental studies on the diesel engine urea-SCR system by using a double NOx sensor system that is arranged in the downstream of the SCR catalyst based on ammonia cross-sensitivity. It was shown that the NOx conversion efficiency rised as $NH_3/NOx$ increases and the ammonia slip started from the $NH_3/NOx$ equal to 1.4. The increase of temperature caused high improvement of the SCR reaction rate while the space velocity had no obvious change. The ammonia slip was in advance as catalyst temperature or space velocity increase and the ammonia storage reduced as catalyst temperature or space velocity increase. The NOx real-time conversion efficiency rised as the ammonia accumulative storage increase and reached the maximum value gradually.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.80-86
• /
• 2008

Recently, controlled auto ignition(CAI) in gasoline engines are drawing more attentions due to its extremely low level of NOx emissions and potentials in lowering the fuel consumption rate. The one of the key techniques for realizing CAI combustion in engines is the control of valve system. Since the valve linkage system with higher complexity, or even earn-less valve systems, such as electro-hydraulic and electro-magnetic system, are adopted in CAI engines, it is not easy to estimate the valve lift profile from earn profiles. Therefore new measurement techniques for valve lift in CAI engines have been tried and tested. In this paper, hole type valve lift sensor was developed and tested to check the applicability in CAI engines. The valve lifts could be obtained from the sensor signal, which depends on the distance from the sensor to magnet attached to valve. Various engine speeds, ranging from 2,000 to 6,000 rpm, and valve lifts, maximum up to 9.7 mm, were tested. It was found that the sensor output for valve lift had accuracy of 98% in comparison with the basic specifications of valve lift through improvements of sensor driving circuit.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.85-91
• /
• 2000

Oxygen sensors taken from the aftertreatment systems of 4 vehicles which had been aged in domestic filed were examined for aging pattern using a idle engine bench. The sensors were then cut into each layers along their components and characterized for poisoning, surface area and morphology. This study shows that amplitude and mean value of aged sensors are seriously affected by high temperature and oil components of exhaust gas.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.5
• /
• pp.740-745
• /
• 2008

This paper presents a new non-contact 3D robotic inspection system to measure the precise positions of screw and punch holes on a car body frame. The newly developed sensor consists of a CCD camera, two laser line generators and LED light. This lightweight sensor can be mounted on an industrial robot hand. An inspection algorithm and system that work with this sensor is presented. In performance evaluation tests, the measurement accuracy of this inspection system was about 200 ${\mu}m$, which is a sufficient accuracy in the automotive industry.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.868-874
• /
• 2011

In this paper, a new structure to improve the resolution of an inductive torque sensor is proposed. The new coupling structure and the change of number of turns for the receiving coil increase the resolution of the torque sensor. Because this torque sensor has non-contact points, it has no abrasion at the contact point, and is very durable. Also, the torque sensor has less variation due to vibration or strain, and it has a good EMC(Electromagnetic Compatibility) and thermal characteristics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.4
• /
• pp.8-17
• /
• 2010

In this paper, a fault tolerant control against sensor faults of electric parking brake (EPB) is proposed. Fault tolerant control method of EPB system is strongly demanded since sensor faults can endanger a driver's safety. In this paper, a clamp force estimation method is presented using motor's armature current and angular velocity. Clamp force estimation method is applied for fault detection method with parity equations. The goal of the detection method is to detect and identify faults in encoder, current sensor, force sensor, and parking cable. And a switching logic for fault tolerant control against the three sensor faults is suggested. Experimental results show that the proposed force estimation method satisfies the specifications of EPB system. The effectiveness of the fault detection method is validated with experimental results. Although a single sensor fault happens, EPB system with the proposed fault detection method does not develop into a failure on subsystem or system level.

• Journal of Sensor Science and Technology
• /
• v.30 no.2
• /
• pp.88-93
• /
• 2021

In this paper, a folding sensor based on capacitance is proposed. The sensor was developed to sense the length and angle data for the milli-scale actuators without causing any interference to the actuating joints. For the sensing and testing the robotic joint with reducing the cost and complexity aspects of manufacturing, a simple composition was adopted. The sensor comprises a pair of copper tapes, papers, and wires. The complete sensing unit is constructed by bonding the tapes with the papers and soldering the wire to the copper parts. For accuracy, a teensy 4.0 board, which has a 12-bit ADC resolution, is employed. Furthermore, the sensed analog data is not translated into the unit of capacitance for accuracy; however, it is filtered using a low-pass filter and subsequently, a Butter-worth filter. The data obtained demonstrate a periodic waveform, which implies that the data are in good agreement with the hypothesis set prior to the experiments. Compared to other milli-scale sensors, this could be a better option for sensing the length and angle data for milliscale actuators.