• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.103-111
• /
• 2001

During cold-start period, the reduction of exhaust emissions is a challenging task. To decrease harmful gaseous substances such as HC, it is necessary to realize a fast catalyst warm-up. In this study, the performance of dual pipe exhaust system have been carried out through different test mode. From measurement of gas temperature and HC concentration, the following conclusions were derived ; 1) Compared with single pipe, dual pipe exhaust system remarkably increase temperature of exhaust gas going through M.C.C(Main Catalytic Converter). 2) W.C.C.(Warm-up Catalytic Converter) also decreases HC emission. To reduce HC emission, it is helpful to use W.C.C. as well as dual pipe exhaust system. 3) Using finite element method, it is shown that inner parts have much higher distribution of temperature than outer parts.

• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.27-31
• /
• 2007

The number of vehicles employing diesel engines is rapidly rising. Accompanying this trend, application of an after-treatment system is strictly required as a result of reinforced exhaust regulations. The Diesel Particulate Filter (DPF) system is considered as the most efficient method to reduce particulate matter (PM), but the improvement of a regeneration performance at any engine operation point presents a considerable challenge by itself. Therefore, the present study evaluates the effect of fuel injection characteristics on regeneration performance in a DOC and a catalyzed CR-DPF system. The temperature distribution on the rear surface of the DOC and the exhaust gas emission were analyzed in accordance with fuel injection strategies and engine operating conditions. A temperature increase more than BPT of DPF system was obtained with a small amount fuel injection although the exhaust gas temperature was low and flow rate was high. This increase of temperature at the DPF inlet cause PM to oxidize completely by oxygen. In the case of multi-step injection, the abrupt temperature changes of DOC inlet didn't occur and THC slip also could not be observed. However, in the case of pulse type injection, the abrupt injection of much fuel results in the decrease of DOC inlet temperatures and the instantaneous slip of THC was observed.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.2
• /
• pp.79-85
• /
• 2009

We aimed to develop a Fe-($16{\sim}19$)Cr-($0.1{\sim}0.6$)Ti-($0.1{\sim}0.6$)Nb stainless steel for automotive exhaust parts with high corrosion resistance. The alloys with high Cr content showed high resistance to general corrosion and also localized corrosion. The increase of Ti and Nb contents resulted in a linear increase in the general corrosion resistance, while the pitting potential was improved by addition of these elements up to about 0.4 wt.%. The low-carbon Fe-17Cr-0.4Ti-0.4Nb alloy annealed at $850^{\circ}C$ and air-cooled was considered to be the optimum alloy for our purpose with the critical anodic current density of $247{\mu}A/cm^2$ in 0.05 M $H_2SO_4$ solution and the pitting potential of 310 mVSCE in 0.2 M NaCl solution.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.209-212
• /
• 2008

Hydroforming Technology has been applied to manufacture in various parts of automobile. Especially, Exhaust manifold has been applied to hydroforming method in the foreign advanced automotive company. Exhaust manifold runner is important exhaust parts that heat-resistant and exhaust flow characteristics are requested in the automobile. The purpose of this study is to optimize the manufacturing method of exhaust maniflold runner using FEA and to propose to get a optimization design direction. In addition, Comparative analysis between conventional exhaust maniflold and hydroformed exhaust maniflold has been done in view of weight-saving, manufacturing advantage.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.23-28
• /
• 2014

This study investigates fluid flow and thermal stress at automotive exhaust manifolds as model 1 and 2. The maximum displacements happen at joint part connected with 4 pipes and upper middle of both parts in cases of model 1 and 2 respectively. At inner surface of the part connected with engine, maximum equivalent stresses of 991.85 and 698.96 MPa are shown in cases of model 1 and 2 respectively. As maximum velocities at the outlet at model 1 are shown at 19.46 and 14.61 m/s in cases of model 1 and 2 respectively, model 1 has more pressure drop than model 2. As result, model 2 has less pressure drop than 1. Model 2 has less deformation and stress than model 1. Model 2 has also less pressure drop than model 1. Therefore model 2 has more strength durability than model 1. This study result is applied with the design of safe automotive manifold and it can be useful to improve the durability by predicting prevention against the deformation due to exhaust gas.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.34-43
• /
• 1992

The purpose of this study is to consider the performance and exhaust characteristics in the practical engine according to the cooling water temperature change of engine and to set up the optimum cooling condition and to obtain the optimum operating condition of thermostat in the cooling system. In order to accomplish the purpose of this study, authors have used the following procedure. 1. This study is to investigate the influence of the cooling water temperature on the engine performance and the exhaust gas, authors regulated the cooling water temperature by using the special closing circuit and measured the concentration of exhaust gas by using the exhaust gas measuring system in the exhaust pipe. 2. This study carried out the experiment by regulating the opening degree of throttle valve and engine speed in the dynamometer and by changing the cooling water temperature, at the same time kept air-fuel ratio constant and made the spark ignition time MBT(Minimum spark advance for Best Torque) 3. This study measured the cooling water temperature by using the K-type thermocouple centring around the easy over-heated parts and by installing a special closing circuit. Therefore, in this study, authors intend to examine the influence of the cooling water temperature on the engine performance, exhaust gas and present the basic materials needed in the engine design including the optimum operating time control system for the cooling water temperature.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.75-80
• /
• 2014

In previous study, make an attempt to estimate exhaust valve seat and seat-ring wear acceleration factor for engine durability test with measuring and consideration of wear mechanism. But found abnormal initial wear rate in exhaust valve seat-ring. And have to improve exhaust valve seat-ring wear rate for reliability reason, because next GDI/Turbo engine is based on this engine and GDI/Turbo engine have higher combustion pressure and higher thermal load. In this study, Trying to find the cause of abnormal wear factor, improve valve-train durability by change specification & design of parts and verify variant parts for improving durability of valve-train. And then I would like to propose a design guide line of valve-train system in a reliability point of view, besides make a complement of previous study.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.72-79
• /
• 2009

Recently, the internal combustion engines have focused on reducing the $CO_2$ gas in order to cope with severe regulations for fuel economy. Therefore, various new technologies have been developed. Among them, cooling system is spotlighted because it has great effect on fuel economy. In this study, we measured the friction losses of engine parts according to engine speed and oil temperature. We also obtained optimized oil temperature which has the minimum friction losses. Then, we selected optimized oil temperature range and gave informations of friction losses for each engine parts. In addition, we analyzed relationship between coolant temperature and oil temperature by using engine performance test system. From this experiment, we obtained the database for relationship between coolant temperature and oil temperature. Then, we found the optimal temperature about engine oil. We analyzed BSFC and exhaust emissions by controlling the high coolant temperture. If we controlled coolant temperature more higher, BSFC has a little difference but exhaust emissions such as THC and CO have reduced. By using these experimental results, we predicted that IC engine have more low fuel consumption and exhaust emissions by optimized cooling control strategy.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.3
• /
• pp.57-70
• /
• 1992

As automobile industry develope, design techniques to satisfy light weight and high efficiency in automobile parts is demanded. In this study modal analysis is performed using transfer matrix method to identify dynamic characteristics of exhaust system. It is estimated the theoretical transfer function by Pestel-Leckey method and the mode shapes in 3-D graphic. the validity of developed program is verified by comparing with the experimental results of exhaust system. Estimated modal parameters(natural frequency, vibrational mode, transfer function) are in accord with the experimental results. From the developed program, we can predict a location of the hanger which is determined by the lowest RMS value point, when displacement is given as an input at the engine side. We can find that attachment of spring modelled hanger at the hanger location bring vibration level down.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.