• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.367-375
• /
• 2004

We have developed a highly efficient boiler system using the 2,600cc Diesel engine. In this system, the co-generation concept is utilized in that the electric power is produced by the generator connected to the engine, and waste heat is recovered from both the exhaust gases and the engine itself by the shell-and-tube heat exchangers. The heat exchanger connected to the engine outlet is specially designed such that it not only recovers waste heat effectively from the exhaust gases, but significantly reduces an engine noise. It is found that the total efficiency(thermal efficiency plus electric power generation efficiency) of this system reaches maximum 96.3％ which is about 15％ higher than the typical Diesel engine boiler system currently being used worldwide.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.20-25
• /
• 2012

As a kind of distributed energy system, the co-generation system based Diesel engine using after-treatment device was devised for its environmental friendly and economic qualities. It is utilized in that the electric power is produced by the generator connected to the Diesel engine, and waste heat is recovered from both the exhaust gases and the engine itself by the finned tube and shell & tube heat exchangers. An after-treatment device composed ceramic heater and DOC(Diesel Oxidation Catalyst) is installed at the engine outlet in order to completely reignite the unburned fuel from the Diesel engine. In this study, mutual relation of each experimental condition was derived through minimum number of experiment using Taguchi Design and ANOVA recently used in the various fields. It is found that the total efficiency (thermal efficiency plus electric power generation efficiency) of this system reaches maximum 94.4% which is approximately higher than that of the typical diesel engine exhaust heat recovery system.

• 오토저널
• /
• 제14권4호
• /
• pp.61-67
• /
• 1992

The ignition timing feedback control system was studied to enhance the engine power and to reduce the fuel consumption by optimizing the spark timing. The signal of a piezo-electric vibration transducer attached to the engine block was compared with that of a pressure transducer in order to determine the knock intensity. With the result of comparison the ignition timing feedback control system which detect the knock and correct the spark timing was set up. The ignition could be more advaced with this control system than the existing system without the continuous knocking, therefore the engine torque was increased.

• 정보처리학회논문지:소프트웨어 및 데이터공학
• /
• 제5권7호
• /
• pp.339-344
• /
• 2016

자동차 소프트웨어의 복잡성이 높아짐에 따라 안전문제가 중요해졌다. 그래서 이를 해결하기 위하여 Automotive SPICE 프로세스가 제안되었다. Automotive SPICE 프로세스 수행을 위해서는 통합된 관리 체계와 도구가 필요하다. 하지만 중소기업의 경우에는 인원과 자본이 부족하여 통합된 관리체계와 도구를 도입하기 힘들다. 따라서 Automtovie spice 최소 요구사항을 준수하는 HIS scope 항목을 목표로 해야 한다. 본 논문에서는 Automotive HIS scope 항목을 수행하는데 필요한 오픈 소스 기반 프로세스 관리 도구 시스템을 제안한다. 제안된 시스템으로 Automotive SPICE HIS scope 항목을 수행할 수 있으며, 수행 결과를 통하여 Automotive SPICE HIS scope 항목을 만족하는 것을 보였다.

• 한국전자통신학회논문지
• /
• 제13권3호
• /
• pp.555-560
• /
• 2018

본 논문에서는 실차기반의 전기자동차 진단시스템을 활용한 교육용 콘텐츠에 관한 연구를 대상으로 한다. 먼저, 최근 늘어나고 있는 전기자동차의 이해를 돕기 위해 전기자동차를 구성하고 있는 핵심 부품과 전기자동차의 주행모드와 동작원리에 대해서 기술한다. 또한 전기자동차 시험 장치와 특성분석을 위한 진단시스템을 구현하였으며 실차기반의 실험 수행을 통해 주행모드에 따라 나타나는 특성을 분석하였다.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.40-48
• /
• 2013

Recently, many types of electric vehicles including a heavy duty vehicle have been developed and released because of the better fuel economy and less gas products. In this study, research about an electric bus which utilizes the wheel motor drive system was conducted. The wheel motor is a motor connected to the wheel directly only with a simple gear so that the developer can utilize the space efficiently and the whole system efficiency will be better because of simple structure. However, because it is different from former types of vehicles which use the differential gear, the development of the integrated control logic is required in order to meet the vehicle stability and driving performance. The developed control logic is composed with direct yaw moment control, regenerative braking control and slip control logics. It is compared to the control logics which does not consist of direct yaw moment control and slip control when the vehicle is exposed in tough situations. For the unification of the control logic, a few maps were developed and applied to determine the output torque of each motor according to the driving status. As a result, it is shown that the developed control logic is more safe and well follow the target speed than the other control logic applied simulations.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.154-161
• /
• 2004

A new column type electric power steering system (EPS-TT) is proposed in this study. The remarkable features of EPS-TT are its opto-isolated torque sensor and assist torque control methodology. EPS-TT uses a uni-directional motor and two clutches. Full order and simplified models for EPS-TT are developed to evaluate the EPS-TT. A full car model is also used to investigate the vehicle responses. A PID control logic is designed to control the torque of the assist motor. Various sinusoidal inputs are applied to the system and the resulting performances are analyzed. The results prove that the performances achieved by the EPS-TT are improved compared to those of a conventional EPS-TT across the frequency domain. In addition, it is inexpensive and easy to control the motor. The results of the full order steering system model are similar to those simplified model, but the vehicle responses are slightly different.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.172-178
• /
• 2003

Driving range is one of the main problems in development of Electric Vehicles(EV). The Regenerative. braking system is required to overcome the problem, which converts kinetic energy of the vehicle during braking into electrical energy. This paper discusses the braking system of EV and Robust design especially developed to maximize energy recovery and to optimize braking performance. This is promised to be applied to the design of elements for EV braking system.

• International journal of advanced smart convergence
• /
• 제10권4호
• /
• pp.256-262
• /
• 2021

In order for small electric vehicles to drive on hilly roads in Korea, methods to improve the climbing ability and power performance of vehicles should be taken. In order to improve the power performance of small electric vehicles, the performance of motors mounted on electric vehicles should be improved. However, if the performance of the motor is improved to improve the power performance of the electric vehicle, it is possible to lower the price competitiveness accordingly. In addition, the power consumption of the battery is rapidly increased to drive the high-performance motor, so in order to introduce the small electric vehicle into the domestic market, various problems must be overcome. In order to commercialize small electric vehicles that do not emit harmful exhaust gases to the human body in the hilly domestic terrain, it is effective to introduce a separate continuously variable transmission system that can improve the climbing ability and power transmission ability. In this study, we propose a proprietary model of continuously variable transmissions that can be applied to small electric vehicles. The proposed continuously variable transmission is equipped with a spring in the driving pulley and the driven pulley, and has the advantage of performing a shift that increases torque in a situation where the vehicle needs to increase torque when driving on a hill. In addition, the basic design for commercialization of the proposed continuously variable transmission was carried out, and the prototype manufactured and attached to the body of a small electric vehicle.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.250-256
• /
• 2014

EV(Electric Vehicle) has many benefits such as prevention of global warming and so on. But due to driving source changing from combustion engine to battery and e-motor, new R&D difficulties have arisen which changing of desired vehicle performance and multidisciplinary design constraints by means of strong coupled multi-physics domain problems. Additionally, dynamics performances of EV becomes more important due to increasing customer's demands and expectations for EV in compare with internal combustion engine vehicle. In this paper suggests model based development platform of EV through integrated simulation environment for improving analyse & design accuracy in order to solve multi-physics problem. This simulation environment is integrated by three following specialized simulation tools IPG CarMaker, AVL Cruise, DYMOLA that adapted to each purpose. Furthermore, control algorithm of TV(Torque Vectoring) system is developed using independent driven e-motor at rear wheels for improving handling performance of EV. TV control algorithm and its improved vehicle performances are evaluated by numerical simulation from standard test methods.