• 한국기계가공학회지
• /
• 제12권1호
• /
• pp.28-34
• /
• 2013

For the senses of beauty and texture, internal components of small passenger cars are manufactured by texturing plastic with drawplate but those of deluxe passenger cars are manufactured by bonding pre-embossed skin to the surface of drawplate. As the pre-embossed skin is bonded at high temperature and pressure, the pattern of skin is distorted. The corner part is hardened and its dimension tolerance is changed by resulting in the increase with its defective rate. This study provides the method to design and manufacture the door trim track by vacuuming the non-patterned skin to upper-side drawplate which forms the pattern of descending skin. It is pressed to the plastic product with hot-press method and the damage of bossed-pattern is prevented. Valuation in this study has been done by analyzing, designing and experimenting method.

• 한국자동차공학회논문집
• /
• 제18권1호
• /
• pp.74-85
• /
• 2010

In order to formulate the compounded polypropylene(C-PP) which is suitable to an automotive door trim panel, 9 sorts of properties were measured after manufacturing the C-PP using an extruder and an injection machine with polypropylene(PP), ethylene-octene rubber(EOR) and talc. Mixture design, especially extreme vertices design, in DOE with MINITAB - commercial software was used to analyze the data. The relations between each property and each component, for example, $y=0.00907222x_1+0.00870556x_2+0.0155722x_3$ for specific gravity, were found out by the regression analysis and the variance analysis. The optimized formulation of the C-PP for an automotive door trim panel was acquired at PP(77.6962), EOR(11.0238) and talc(10.2800) by use of the response optimizer(mixture) in MINITAB.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.137-138
• /
• 2006

TPOs based on polypropylene has been dominating materials in hard automotive parts such as in bumper fascia, instrumental panel and door trim panel owing to their variety of advantages compared to engineering plastics and steels for years. Recently as environmental regulations related to recycle have been strengthened, the use of TPOs in soft automotive parts such as instrument panel skin and door trim skin is being required much more.. Therefore, in this study, we' d like to give an overview of soft TPOs and introduce soft TPO materials requirement and preferable materials composition by vacuum thermoforming and powder slush molding, respectively.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권3호
• /
• pp.7-12
• /
• 2008

Today, manufacturers are forced to acknowledge that the life cycles of products are becoming shorter. In the case of the door trim assembly field, the highly frequent introduction of new products and the continuous increase in product varieties leads to the demand for redesigning assembly systems more often. Modular manufacturing systems can be an important issue in helping to overcome these problems. This paper presents the development of a modular assembly system for the door trim, and because it takes the change drives into consideration, this system is highly flexible in adapting to changes in the environment.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.138-144
• /
• 2004

Occupant protection in the side impact of a vehicle becomes one of the most important issues today. So, to reduce development time and cost, it needs test equipment which conducts an accurate simulation of the side impact crash. This paper describes a new test method for side impact, which utilizes a standard 12inch-HYGE-type sled facility. If a side impact sled test can simulate vehicle intrusion very well, it will contribute to develop full-scale side impact crash performance. The newly developed sled test method enables simulation for dummy motion, injury, door velocity, trim crack, and vehicle structure to be accurate. Ant also this sled test method can be applied to the development of side air-bag.

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.44-52
• /
• 1996

A procedure predicting warpage and post-deformation due to heat resistance test is presented. The procedure is applied to the injection molding processes of automotive plastic components, which are the door trim and the instrument pannel. The warpage of products is obtained from the residual stress after filling, packing and cooling process, and the post deformation due to the heat resistance test is calculated in the structural analysis of the product at the ejection temperature with the initial condition of residual stress, the boundary conditions and heat resistance conditions. The analyses give some useful guide lines in the design of automotive plastic parts which should satisfy heat resistance regulation.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권1호
• /
• pp.42-50
• /
• 2005

In order to increase competitiveness and to gain economic benefit, companies ask more and more how to recycle their products in an efficient way. So far, to answer this question, companies are not sufficiently supported by suitable methods specially in the area of disassembly process planning. For this reason, we develop in collaboration with an industrial partner a new method for generating an optimal disassembly sequence. In this paper this method will be described in detail by considering the exiting assembly information, disassembly method and disassembly depth. PLM(Profit-Loss Margin) curve that is used to determine disassembly depth consists of profit value, disassembly cost and disassembly effect. Using assessment parameters, generated alternative disassembly sequences are evaluated and an optimal disassembly sequence is proposed. This method is applied to generate the optimal disassembly sequence of Door Trim as an example.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.115-122
• /
• 2014

Injection pressure is one of factors that influence part quality. In this paper, injection pressure was minimized by optimizing valve gate locations. In order to perform design optimization, MAPS-3DTM (Mold Analysis and Plastic Solution-3D) was used for injection mold analysis and PIAnOTM (Process Integration, Automation and Optimization) was used as process integration and design optimization. Also we adapted meta models based on design of experiments for efficiency. By using introduced methodology, we were able to obtain a result so that maximum injection pressure reduced by 28% compared to the initial design. And the validity of the proposed method could also be demonstrated.

• 대한산업공학회지
• /
• 제41권4호
• /
• pp.344-351
• /
• 2015

Recently, an ERP (Enterprise resource Planning) system has been becoming an essential S/W tool for companies to manage their business processes and manufacturing resources. As the information exchange becomes more complex, not only corporate companies but also small- and mid- sized enterprises (SMEs) are required to build an ERP system. However, for small- and middle- sized companies, the adoption of ERP systems becomes challenging due to high cost and long installation time of the system. This paper presents a novel concept of an adaptive ERP system incorporating the ontology structure of the business supply chain information. The proposed ERP installation methodology is illustrated with an example of a door-trim manufacturing company in the automotive supply chain.