• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.249-254
• /
• 2000

The contact forces between die components for the drawing of large size automotive panels introduce elastic deflections of the die components. Due to the deflections, the gap between blank holder and die varies locally resulting in nonuniform material flow. Such a nonuniform die gap usually requires correcting operation, so called die spotting, which is time consuming trial and error process. To reduce the die spotting time, the optimization of the blank holder bending deflection is needed. In this paper, we implemented an analysis procedure to predict the blank holder deflection. The analysis procedure and design of experiments techniques are applied to the optimization of balance block heights. The optimization results can be used as guidelines in actual die spotting process.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.54-61
• /
• 1984

Numerical calculation of the flow field past a passenger car was carried out by using a panel method with a small computer of 5Mbyte memory size. The shape of car body was simplified and reconstructed by 2180 panels on which a constant strength sink (or source) was distributed. The separation of flow from the surface and the wake flow were not considered in the calculation because of the computer memory limitation. All of the results of calculation were presented by using a 3-dimensional computer graphics. In spite of small memory size of computer, generally good agreements were obtained, except the separated region, from the comparison of pressure distribution between numerical analysis and wind tunnel experiment with 1/5 scaled model.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.2
• /
• pp.176-184
• /
• 2003

New lubricant film of organic and inorganic composite resin was developed to improve the press formability of galvannealed steel sheets (GA) for automotive body panels. The frictional coefficient of lubricant GA steel sheets is about 20% superior to that of uncoated GA. The current range of spot welding of lubricant GA is similar to that of the uncoated GA, but the burning trace of spot welding is inferior to that of the uncoated GA in the oiling condition. The alkaline degreasability of lubricant GA shows 100% in alkaline degreasing condition of automotive company. The size and shape of the phosphated coating layer are similar to those of the uncoated GA sheet. The powdering property of the lubricant GA gives rise to 20∼50% improved property compared with the uncoated GA sheet.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1998.10a
• /
• pp.36-40
• /
• 1998

Tool shop of the‘D’Motor Co.(DMC) fabricates dies for producing automotive press panels. In order to increase the production capacity of the tool shop, DMC established an FMS that consists of high-speed machines and a CMM at the tool shop in 1997. Due to the difference in machine capability among the existing machines and the new FMS it is needed to find an optimal way of allocating workloads among machines to maximize the production. In a way to solve this, we model the die fabrication process of the tool shop and analyze its performance by computer simulation. In this study, we at first identify the bottleneck processes of the die fabrication process under the current operation policy. Then, we derive some alternative operating policies applicable to the tool shop, and analyze the optimal operation policy by comparing the performance of the tool shop following each alternative policy.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.82-85
• /
• 2005

In order to see the effect of die deformation on the forming of sheet metal, the draw-ins, strains, and springbacks of an automotive fender panels are numerically simulated considering the die deformation found by the simultaneous structural analysis of press and dies. The comparison of the forming analysis result between the rigid die and the deformed die layout shows that the deformed tool provides more accurate forming and springback result.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.36-43
• /
• 1998

Surface roughness of cold rolled steel sheet as well as the coating technique itself is quite important in obtaining high image clarity of electronic products and car outer panels. Especially, surface characteristics of steel sheet have acquired increasing attention from the steel and automotive industries. While the influence of such characteristics on paintability formability and painted surface appearance is important in defining steel surface requirements for automotive industries. Therefore this paper is dedicated primarily to the issue of paint appearance and reviews for improvement of roughness and peak count about the surface of work roll for the actual temper mill. The conclusions were obtained as follows ; 1) Roughness and peak count about the surface of steel sheet is strongly affected by surface condition of work roll. 2) The electro-discharge textured roll has more uniform roughness distribution than shot blasted roll and it's painted appearance of steel sheet has more improvement than that of the shot blasted because it has more harmonic wave roughness, and the higher peak count of surface roughness.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.485-492
• /
• 2006

The AA5182/polypropylene/AA5182(AA/PP/AA) sandwich sheets have been developed for application to automotive body panels in future lightweight vehicles with significant weight reduction. It has been reported that the AA5182 aluminum sheet shows $L\"{u}ders$ band because of dissolved Mg atoms that cause fabrication process problem, especially surface roughness. The examination of serration behavior has been made after the tensile deformation of the AA/PP/AA sandwich sheets as well as that of the AA5182 aluminum skins at room and elevated temperatures. All sandwich sheets and the AA5182 aluminum skin showed serration behavior on their flow curves. However, the magnitude of serration was significantly diminished in the sandwich sheet with high volume fraction of the polypropylene core. According to the results of the analysis of the surface roughness following the tensile test, $L\"{u}ders$ band depth of the sandwich sheet evidently showed lower than that of the AA5182 aluminum skin. The strain rate sensitivity, m-value, of the AA5182 aluminum skin was -0.006. By attaching these skins to the polypropylene core, which has relatively large positive value of 0.050, m-value of the sandwich sheets changed to the positive value. The serration mechanism of the sandwich sheets was quantitatively investigated in the point of the effect on polypropylene thickness variation, that on the strain rate sensitivity and that on the localized stress state.

• International Journal of Automotive Technology
• /
• v.6 no.3
• /
• pp.259-268
• /
• 2005

In order to analyze the sheet drawability, the measurement of the plastic strain ratio was carried out for the 5182 aluminum alloy sheets in which were cold rolled without lubrication and subsequent recrystallization annealing. The average plastic strain ratio of the 5182 aluminum sheets was 1.50. It was considered that the higher plastic strain ratio was resulted from the ND//<111> component evolved during rolling and maintained during annealing. The AA5182/polypropylene/AA5182 (AA/PP/AA) sandwich sheets of the 5182 aluminum alloy skin sheet and the polypropylene core sheet with high formability have been developed for application for automotive body panels in future light weight vehicles with significant weight reduction. The AA/PP/AA sandwich sheets were fabricated by the adhesion of the core sheet and the upper and lower skin sheets. The AA/PP/AA sandwich sheet had high plastic strain ratio (1.58), however, the planar anisotropy of the sandwich sheet was little changed after fabrication. The optimum combination of directionality of the upper and lower skin sheets having high plastic strain ratio and low planar anisotropy was calculated theoretically and an advanced process for producing the sandwich sheets with high plastic strain ratio was proposed. The developed sandwich sheets have a high average plastic strain ratio of 1.55 and a low planar anisotropy of 0.17, which was improved more by 3.2 times than that of 5182 aluminum single sheet.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.125-129
• /
• 2003

The identification of location and strength distribution of extended noise sources is important in the practical noise control engineering, especially in the viewpoint of dealing with the inherent nature of noise problem in question. For noise source ranking inside an automotive vehicle, the window method has been mainly used due to its simplicity. However, time and cost drawbacks in the measurement and inaccuracy due to low-frequency tunneling and lack of phase information have been a serious problem in using this method. In this study, the inverse FRF method was employed to carry out the noise source ranking inside an automotive vehicle and it was also used to predict the interior sound pressure with the change of sound insulation materials. As a result, it was found that the source contribution of vehicle panels could be successfully identified in comparison with the window method. The sound pressure at driver's ear position was predicted based on the obtained data and was compared with the measured data. The agreement in spectral trends was acceptable and their difference in level was within 3㏈ above 500㎐.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.6
• /
• pp.642-649
• /
• 2015

Resistance Spot Welding (RSW) is the method for joining two overlapped base materials when high pressure and current is applied from electrodes. Due to the safety problem such high pressure and voltage, automation should be early adopted. In this paper, the spot welding is developed as a computational model of wheel house from GM Korea and the welding condition such as weld sequence is considered. The computational analysis is preceded as a static and elasto-plastic procedure and used thermal expansion coefficient represents a dependency of spot volume between two panels. In case of welding sequence, the efficiency which depends on the distance between current spot point and the other is calculated in several cases.