• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.31-38
• /
• 1992

The objective of this study is to determine the ignition feasibility of a single shot, air-assisted gasoline fuel injector operated in a constant volume combustion chamber under atmospheric condition. A number of parameters has been selected for this experiments, such as dwelling time, spark gap position(r,z), spark electrode geometry, supplied air and fuel masses and spray cone deflector angle. On-site visual inspection of the instantaneous flame glow was chosen as one way to judge the successful ignition. In addition, chamber pressure and occasional photography were mobilized as for data recording. It was clearly observed that there was an entrainment air-fuel mixture toward spray axis from the spray formation and its development later on. The optimum ignition conditions were found for those parameters given above.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.1-10
• /
• 2001

In order to reduce hydrocarbon emissions of spark ignition engine, it is important not only to improve catalyst conversion efficiency but also to reduce direct engine out hydrocarbon emissions, during cold starting and warm up process. Tjerefore many researchers have been attracted to develop an early fuel evaporator (EFE) by introducing a ceramic heater for a solution of engine out hydrocarbon emissions in SI engine. But, the performance of the EFE in MPI engine to reduce the exhaust emissions and to improve the cold startability has nat been clarified yet. The purpose of this study is to evaluate the feasibility of a glow plug for EFE.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.4
• /
• pp.100-111
• /
• 1994

Observations on the near-nozzle behavior of an unsteady fuel spray through single cylindrical hole nozzle were made by phase Doopler anemometer and microphotographs. At the edge of the spray, droplet velocity peaked during needle opening and closing. Droplet sizes tended to be small on the edge of spray. The near-nozzle spray angle taken from the microphotographs was time-dependent, even though it increased with gas-to-liquid density ratio as expected. The near-nozzle spray angle was the greatest on the initial stage and decreased to a relatively constant value after about one third of the total injection duration regardless of the ambient gas conditions, even in the near-vaccum condition. The wider near-nozzle spray angle in the early stage is due to the flow characteristics inside the nozzle rather than aerodynamic interactions. However, once the spray was established, aerodynamic interactions are essential in the near-nozzle atomization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.16-21
• /
• 1999

The diesel vehicle is relatively superior to gasoline vehicle on the fuel consumption, durability and combustion efficiency. However, exhaust emission from diesel vehicle are known to be harmful to human health and environment. The treatment technologies for the diesel exhaust gases are classified as replacement of fuel, quality control of diesel fuel, improvement of engine and aftertreatment system. The most effective for the treatment technology is known to be aftertreatment system, and this research is continuously conducted by many groups. The DOC system has many advantages of reducing particulates and harmful gaseous substances such as CO. HC. Moreover, it is simple in device structure, relatively low cost, and easy to install witout retrofitting the vehicle. In this study, experiment were conducted to analyze the effects on factors of oxidation characteristics and conversion efficiency of DOC. In experiment, test was conducted to estimate engine emission in 11,000cc diesel engine which was equipped with DOC.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.17-22
• /
• 2000

The transient process simplified by the 1-D stretched laminar flame formed at the fuel-oxidizer interface was investigated using the coherent flame sheet model. Under the combustion environment of high temperatures and pressures the results show that the time required to reach the steady state was relatively short compared to the reverse of strain rate. Hence the employment of the tabulation of precalculated steady-flame results in the calculation of turbulent diffusion flames using the coherent flame sheet model is concluded valid, Also upstream temperatures were found to have only a minor effect on the nondimensional flame temperature and nondimensional fuel even through the letter is sensitive to pressure changes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.178-185
• /
• 1998

To reduce the particulate matter and nitrogen oxides from diesel engine, many studies are proceeding and being accomplished practically. In this situation CNG engine has important meaning both as a clean fuel and an alternative energy. In order to present the direction and application of CNG, we simulated various operating conditions, that is, spark timing, compression ratio and fuel composition etc. Thus we try to understand how those affect performance and exhaust characteristics. The simulation program results found that the optimum combustion start angle was 21$^{\circ}$ at 1800rpm and fuel composition affects performance and emissions, also we could understand the formation of emission as crank angle is changed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.229-237
• /
• 1996

For the practical use of a fuel injection system using solenoid, some mechanical and electrical problems should be explicitly analyzed. In our study, we have investigated these problems experimentally and have improved such that a solenoid driving circuit is liable to establish a fast reponse and a precise control of injection quantity. This proposed fuel injecton system is capable to control equivalence ratio from low level to high level. Therefore, we expect that this proposed system should be applicable to an actual engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.75-82
• /
• 2003

DME is a good alternative fuel to reduce the smoke remarkably when used in a diesel engine, while problems concerned with low lubricity and high compressibility exist. In the present study, single cylinder DI diesel engine was operated with neat DME and DME blended fuels which are DME-diesel blended fuel and DME-propane blended fuel. The results showed that the power of the neat DME and DME blended fuels was the same as that of pure diesel oil, and the specific energy consumption slightly increased. In addition, smoke emission was considerably reduced with the increase of DME content up to zero level, but NOx emission was slightly increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.9-14
• /
• 1997

The pump-pipe-injector system is that most commonly used type of injection equipment for diesel engines. In this study, a new electromagnetic fuel injection system was designed and carried out the experiment of single cylinder direct injection(DI) diesel engine. This system do not need the cam shaft for fuel injection. The effects of the injection timing on the combustion process and emission were investigated. The results are that 1) atomization was improved, 2) combustion pressure was increased and ignition delay became shorter than before, 3) Low smoke level guarantee with more advanced injection timing without abnormal combustion but NOX concentration was increased as the injection time advanced.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.4
• /
• pp.74-78
• /
• 2010

Turbocharger in the application to a diesel engine was widely used in automobile industries for the improvement of engine performance. To comply with stringent emission standards, ball bearing turbocharger has been developed by applying new emission reduction technology. Up to date turbocharger has been proved as an essential part of diesel engines by demonstrating its improved engine performance, fuel efficiency and reduced emission as well. In this research, the performance of the ball bearing turbocharger was compared by the conventional journal bearing type turbocharger. The results shows that ball baring turbocharger was proved to be 10~13% higher fuel efficiency and 30% less average emission than journal bearing turbocharger.