• International Journal of Automotive Technology
• /
• v.2 no.4
• /
• pp.165-170
• /
• 2001

This study is focussed on the investigation of spray characteristics from the high pressure gasoline injector for the application of gasoline direct injection engine. For the analysis of spray structure of high pressure gasoline injector; the laser scattering method with a Nd-Yag laser and the Phase Doppler particle analyzer system were applied to observe the spray development and the measurement of the droplet size and velocity of the spray, respectively. Also spatial velocity distribution of the spray droplet was measured by use of the particle image velocity system. Experimental results show that high pressure gasoline injector shapes the hollow-cone spray, and produce the upward ring shaped vortex on the spray surface region. This upward ring shaped vortex promotes the secondary atomization of fuel droplets and contributes to a uniform distribution of fuel droplets. Most of fuel droplets are distributed under 31$\mu m$ of the mean droplet size (SMD) and the frequency distribution of the droplet size under 25$\mu m$ is over 95% at 7 MPa of injection pressure. According to the experimental results of PIV system, the flow patterns of the droplets velocity distribution in spray region are in good agreement with the spray macroscopic behaviors obtained from the visualization investigation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.7
• /
• pp.1019-1029
• /
• 2008

In this study, visual investigation of sprays and flames has been performed and soot formation in Diesel and GTL fuels has been compared in a specially designed Rapid Charging Combustion Vessel (RCCV) under various ambient gas $O_2$ concentrations and two injection pressures. It has been concluded that soot in the mixing-controlled combustion of Diesel and GTL fuels has similar tendency to be formed in the leading portion of the jet boundaries. Auto-ignition delay for GTL fuel is shorter than that for diesel fuel. The temporal and special variation of soot concentration in the diesel flame jets at various $O_2$ concentrations was correlated with the heat release rate. Soot concentration appears in the regions when diffusion combustion starts, and its concentration reaches maximum at the peak of heat release curve and then decreases due to oxidation. Visualization by shadowgraph method showed that soot decreases with lower $O_2$ concentration, and higher injection pressure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.74-81
• /
• 2013

Due to its accuracy and efficiency, reduced kinetic mechanism of diesel surrogate is widely used as fuel model when applying 3-D diesel engine simulation. But for the well-developed prediction of diesel surrogate reduced kinetic mechanism, it is important to know some meaningful factors which affect to ignition delay time. Meanwhile, ignition delay time consists of two parts. One is the chemical ignition delay time related with the chemical reaction, and the other is the physical ignition delay time which is affected by physical behavior of the fuel droplet. Especially for chemical ignition delay time, chemical properties of each fuel were studied for a long time, but researches on their mixtures have not been done widely. So it is necessary to understand the chemical characteristics of their mixtures for more precise and detailed modeling of surrogate diesel oil. And it shows same ignition trend of paraffin mixture with those of single component, and shorter ignition delay at low/high initial temperature when mixing paraffin and toluene.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.389-396
• /
• 2017

Restorations of automotive parts have been done ever since the first vehicle was produced. Because the most expensive parts of a vehicle are in the engine system, there have been various restoration methods developed for engine parts. In the case of commercial diesel engines, the fuel injection device is a key and expensive component. It also has a significant effect on vehicle performance. In particular, reduced engine power and increased exhaust gas emissions may result from mechanical damage due to abrasion of the spill valve in the fuel injection system of a diesel engine. In this paper, restoration techniques for damaged parts are applied to restore the abrasion of a spill valve of fuel injection, also called as the "unit injector", of commercial diesel engines. In order to recover the damage, optimized polishing techniques using hard-metal and coating processes are applied. To evaluate restoration techniques for the spill valve, performance and durability tests are performed on a test bench.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.6
• /
• pp.472-479
• /
• 2013

A free piston linear engine could be operated under HCCI combustion due to its variable compression ratios. To obtain HCCI combustion, the free piston linear engine needs a high compression ratio to achieve auto-ignition of the fuel/air mixture. In this study, an idea for obtaining a high compression ratio using the transition from SI combustion to HCCI combustion was proposed. The fuel used in this study is hydrogen, which is considered to be an environmentally friendly fuel. Besides, the effects of key parameters such as equivalence ratio (${\phi}$), load resistance ($R_L$) and intake temperature ($T_{in}$) on the SI-HCCI transition were numerically investigated. The simulation results show that the SI-HCCI transition is successful without any significant reduction of in-cylinder pressure as the intake temperature is increased from $T_{in}$=300K (SI mode) to $T_{in}$=450K (HCCI mode), while the load resistance and equivalence ratio are retained respectively at $R_L=120{\Omega}$ and ${\phi}$=0.6 in both SI mode and HCCI mode.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.2
• /
• pp.230-238
• /
• 2015

The main purpose of this paper is to suggest opportunities for reducing $CO_2$ emission in energy conversion of a vehicle, focused on auxiliary energy improvement in the automotive field. As part of worldwide efforts to curb global warming and to protect the domestic industry as trade barriers, many countries have set goals to regulate greenhouse gas emissions. As an example, new $CO_2$ emission regulation in EU was expected to go into effect strictly in 2020. Therefore, global car-makers need to establish strategic responsiveness of the regulations. This paper shows $CO_2$ economic value by using the correct interpretation of the relevant laws and regulations. The $CO_2$ value analyzed using quantitative figures leads to the possibility of auxiliary(accessories, HVAC, electric apparatus etc.) technology for improving fuel economy. As a result, this study generalizes the meaning of electric power saving for each driving mode by auxiliary energy improvement.

• Journal of the Korean Society of Combustion
• /
• v.21 no.2
• /
• pp.1-6
• /
• 2016

To meet the Tier-4 emission standard, a variety of combustion technology in the field of off-road engine has been applied in conjunction with the engine after treatment technology. In this study, as the basis study for applying VGT and HPL EGR to 3.6 L CRDi engine, exhaust gas characteristics and fuel economy characteristics are confirmed in accordance with VGT and EGR operating conditions. Consequently, in the EGR applicable conditions, 60% VGT vane duty condition was confirmed that the trade-off characteristics between NOx and smoke are advantageous. In addition, in view of BSFC, VGT vane duty is considered desirable to control at around 50%.

• International Journal of Automotive Technology
• /
• v.4 no.1
• /
• pp.47-55
• /
• 2003

The Center for Transportation Research at the Argonne National Laboratory (ANL) supports the DOE by evaluating advanced automotive technologies in a systems context. ha has developed a unique set of compatible simulation tools and test equipment to perform an integrated systems analysis project from modeling through hardware testing and validation. This project utilized these capabilities to demonstrate the trade-off in fuel economy and Oxides of Nitrogen (NOx) emissions in a so-called ‘pre-transmission’ parallel hybrid powertrain. The powertrain configuration (in simulation and on the dynamometer) consists of a Compression Ignition Direct Ignition (CIDI) engine, a Continuously Variable Transmission (CVT) and an electric drive motor coupled to the CVT input shaft. The trade-off is studied in a simulated environment using PSAT with different controllers (fuzzy logic and rule based) and engine models (neural network and steady state models developed from ANL data).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.62-68
• /
• 2004

To comply with stringent exhaust emission standards, it is necessary to reserch on some better quality of automotive fuels. Sulfur in fuels is sulfur compound by DOC and then it caused to the increase of PM on the surface of the catalyst. This research is focused on diesel emission characteristics and poisoning effect on Diesel Oxidation Catalyst when Ultra Low Sulfur Diesel(ULSD) and biodiesel are applied simultaneously. The biodiesel is used to improve viscosity of fuel specially in fuel injection system of engine since the introduction of ULSD may degrade viscosity in the process of desulfurization. Furthermore, this study may provide some basic data for the design of emissions reduction technology.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.307-311
• /
• 2004

In this study, a novel hybrid vehicle is proposed. The vehicle has a flywheel-engine hybrid system. Flywheels are more effective as energy charge systems than electric batteries in a respect of output power density. However, transmissions to effectively drive flywheels are very complex systems such as CVTs (Continuously Variable Transmissions). In the proposed hybrid vehicle, Constant Pressure System is employed, which is hydraulic power transmission. Using Constant Pressure Systems, hydraulic CVTs are easily realized with variable displacement pumps/motors. In this paper, firstly, the proposed flywheel hybrid vehicle making use of Constant Pressure System is described. Secondly, fuel consumption characteristics of the flywheel hybrid vehicle are experimentally examined with the stationary test facility, which employs a flywheel as a load emulating vehicle inertia. Finally, the experimental results and discussions are described. Fuel consumption of 26km/L is expected for 10 mode driving schedule with vehicle mass of 1500kg.