• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.137-143
• /
• 2007

An object of this study is to understand the application characteristics in accordance with changes of EGR rate, applying BD20 reformed by ultrasonic energy irradiation to common-rail diesel engine. BD containing about 10% oxygen has attracted attention due to soaring crude oil prices and environmental pollution. This oxygen decreases soot by promoting combustion, but it also increases NOx. To make up for this problem, an EGR system is applied so that NOx might be decreased. In that case, engine power is lowered and exhaust gas is raised. However, the reformed fuel by ultrasonic energy irradiation is changed physically and chemically, promotes combustion, and thus solves such a problem. As the results of the experimemt, we could identify the optimum EGR rate by investigating the engine performance and the characteristics of exhaust materials in accordance with the EGR rate after ultrasonic energy irradiation to BD20 and applying it to common-rail diesel engine. The optimum EGR rate that can satisfy both engine performance and characteristics of exhaust materials was in the range of 15%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.86-92
• /
• 2003

To analyze the characteristics of ozone formation, measurements of the concentrations of individual exhaust hydrocarbon species have been made under various engine operating parameters in a 2-liter 4-cylinder engine for natural gas and LPG. Tests were performed at constant engine speed, 1800 rpm for two compression ratios of 8.6 and 10.6, with various operating parameters, such as excess air ratio of 1.0~1.6, bmep of 250~800 na and spark timing of BTDC 10~$55^{\circ}$. It was found that the natural gas gave the less ozone formation than LPG in various operating conditions. This was accomplished by reducing the emissions of propylene($C_3H_6$), which has relatively high maximum incremental reactivity factor, and propane($C_3H_8$) that originally has large portion of LPG. In addition, the natural gas show lower values in the specific reactivity and brake specific reactivity. Higher compression ratio of the test engine showed higher non methane HC emissions. However, specific reactivity value decreased since fuel species of HC emissions increase. brake specific reactivity showed almost same values under high bmep, over 500kPa for both fuels. This means that the increase of non methane HC emissions and the decrease of specific reactivity with higher bmep affect each other simultaneously. With advanced spark timing, brake specific reactivity values of LPG were increased while those of natural gas showed almost constant values.

• Journal of Welding and Joining
• /
• v.33 no.2
• /
• pp.69-77
• /
• 2015

High strength steels have been continually being developed to improve in fuel economy in automotive and ensure safety of passengers. New bonding and welding methods have been required for improving weldability on high strength steels. In this study, resistance spot welding and Weld-bond with nugget diameters of 4.0mm, 5.0mm, 6.0mm and 7.0mm were produced and tested, respectively. In order to confirm the effect of nugget diameters on tensile shear characteristic of the Weld-bond, tensile shear characteristics of Weld-bond were compared with those of resistance spot welding and adhesive bonding. Peak load of Weld-bond were increased as the nugget diameter increases. After appearing maximum peak load continuous fracture followed with second peak owing to load being carried by resistance spot weldment. Fracture modes of the adhesive layer in Weld-bond fractures were represented by mixed fracture mode, which are cohesive failure on adhesive part and button failure at resistance spot welds. The results showed that the tensile shear properties can be improved by applying Weld-bond on TRIP steel, and more apparent with nugget diameter higher than 5${\surd}$t.

• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.59-67
• /
• 2016

The automotive manufactures increase their use of lightweight materials to improve fuel economy and energy usage has a significant influence on the choice of developing materials. To meet this requirements manufacturers are replacing individual body parts with lightweight metals, for these the process treating and painting surfaces is changing. The pre-coated steels are newly developed to avoid the conventional complex and non-environmental painting process in the body-in-white car manufacturing. The development of new joining techniques is critically needed for pre-coated steel sheets, which are electrically non-conductive materials. In the present study, dissimilar combination of pre-coated steel and galvanized steel sheets were joined by the self-piercing rivet, adhesive bonding and hybrid joining techniques. The tensile shear test and free falling high speed crash test were conducted to evaluate the mechanical properties of the joints. The highest tensile peak load with large deformation was observed for the hybrid joining process which has attained 48% higher than the self-piercing rivet. Moreover, the hybrid and adhesive joints were observed better strain energy compared to self-piercing rivet. The fractography analyses were revealed that the mixed mode of cohesive and interfacial fracture for both the hybrid and adhesive bonding joints.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.93-99
• /
• 1997

The re quest to develop the engines that are able to run without air or with very little oxygen condition is raised with the interest of ocean science or the mines. This research had already be gun before the world war II, but had been stagnant owing to the appearance of nuclear power. Recycle diesel engines have ability to run under the above mentioned condition the recycle diesel engine recirculates exhaust gases into intake port and consumes additional oxygen supplied by oxygen tank. Carbon dioxide is controlled by the absorber. The combustion and emission characteristics of recycle diesel engines are quite different with conventional one because the working fluids of recycle diesel engines consist of Ar, $CO_2$ and $O_2$ as well as $N_2$. Recycle diesel engine is therefore different with general diesel engine from the viewpoint of intake air composition. It is required to investigate the effect of intake composition in the combustion and emission to know recycle diesel engine. In this study, NOx concentration, smoke and cylinder pressure are measured with the variation of Ar and $CO_2$ Reduces show that the addition of Ar reduces NOx but increases smoke. Otherwise $CO_2$ reduces smoke and NOX simultaneously. Only $CO_2$ increases the ignition delay and both gases increase fuel consumption Ar addition is superior to $CO_2$ addition for the performance of recycle diesel engine system but $CO_2$ has the avantage with respect to emission.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.687-696
• /
• 2007

To increase the reliability of auto-ignition in CAI engines, the thermodynamic properties of intake flow is often controlled using recycled exhaust gases, called internal EGR. Because of the internal EGR influence on the overall thermodynamic properties and mixing quality of the gases that affect the subsequent combustion behavior, optimizing the intake and exhaust valve timing for the EGR is important to achieve the reliable auto-ignition and high thermal efficiency. In the present study, fully 3D numerical simulations were carried out to predict the mixing characteristics and flow field inside the cylinder as a function of valve timing. The 3D unsteady Eulerian-Lagrangian two-phase model was used to account for the interaction between the intake air and remaining internal EGR during the under-lap operation while varying three major parameters: the intake valve(IV) and exhaust valve(EV) timings and intake valve lift(IVL). Computational results showed that the largest EVC retardation, as in A6, yielded the optimal mixing of both EGR and fuel. The IV timing had little effect on the mixing quality. However, the IV timing variation caused backflow from the cylinder to the intake port. With respect to reduction of heat loss due to backflow, the case in B6 was considered to present the optimal operating condition. With the variation of the intake valve lift, the A1 case yielded the minimum amount of backflow. The best mixing was delivered when the lift height was at a minimum of 2 mm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.82-91
• /
• 2017

This paper is a study on the bi-directional DC-DC converter, one of the key elements of 48V-12V dual systems in mild hybrid electric vehicles. Mild hybrid electric vehicles require a bi-directional DC-DC converter that can efficiently transmit power in two directions between a 48V battery and a 12V battery. To develop a bi-directional DC-DC converter with better price competitiveness, upgraded fuel economy, excellent performance and smaller size, this study designed, produced and presented a circuit that improved on the existing one. In the proposed 8-phase bi-directional DC-DC converter, the size of the passive element was reduced through the 8-phase interleaved topology, whereas downscaling had previously posed a difficulty. This study also designed and produced a 2.5kW class prototype. Based on the proposed 8-phase interleaved topology, a size of 227.5 (W) * 172 (L) * 64.35 (H) was achieved. In the boost mode operation and buck operation modes, the maximum efficiency was recorded at 94.04 % and 95.78 %, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.42-48
• /
• 2003

LPG has been a broad concern of pro-environmental alternative fuel for vehicles. Recently, the new Liquid Phase LPG Injection(LPLI) system extends the limit of power of LPG engine and gives a chance to substitute LPG engine for diesel engine of heavy duty vehicles that are the main resources of air pollution in urban area. Large bore size of heavy duty LPG engine derives a serious knock problem. To find an optimal MBT conditions, it is necessary to know how the flame develops in the combustion chamber and find where the knock positions are. In this study. the ion-probe head gasket was used to estimate the knock position. Inverse operation of the ion-probe signal provides the flame developing characteristics. The further the position is from the spark plug, the later the flame arrives and the more times knock occurs. The main factor that effects knock position is inferred a flor situation of mixed gas in the combustion chamber.

• Journal of Hydrogen and New Energy
• /
• v.26 no.3
• /
• pp.287-293
• /
• 2015

The current study has investigated the effects of biodiesel blended with gasoline on the spray characteristics in a Constant Volume Combustion Chamber (CVCC). With the concentration of 5, 10, 15 and 20% by volume, biodiesel was blended with commercial gasoline and performed on the macroscopic visualization test. Pure gasoline and biodiesel were also tested as the reference. The shadowgraph technique was conducted in the constant volume chamber. The spray images were recorded by a high speed video camera with frame speed 10,000 frame per second. Fuel injection was set at 800, 1000 and 1,350 bar with the simulated speed 1,500 and 2,000 rpm. The back pressure was controlled at 20 bar. The spray angle and penetration tip were measured and analyzed by using the image processing. At the high injection pressure, the spray penetration length with the simulated speed 1,500 rpm showed that B100 was lower than GB00-20 whereas the spray penetration length with the simulated speed 2,000 rpm exhibited that GB blends and B100 were insignificantly different. Due to biodiesel concentration, its effects on spray angles were observed throughout injection periods (T1, T2 and T3). At the simulated speed 1,500 rpm, the spray angle of GB blends and B100 presented the same pattern following injection timing. In addition, when the simulated speed increased to 2,000 rpm the different spray angle of all blends disappeared at main injection (T3).

• Journal of the Korea Convergence Society
• /
• v.11 no.7
• /
• pp.151-155
• /
• 2020

In this study, the velocity distribution and pressure of the flow with the shape of the aircraft were analyzed to investigate its flight performance. In order to compare the flow rate and its pressure applied on the surface of airplane each other, models A and B have the blunt and sharp shapes as the distinctive shapes of airplanes. It can be inferred that the lower the maximum speed of the flow around the airplane, the less resistance the navigation produces, the less fuel consumption, which is more efficient for the sharp model B than the blunt model A. As the result of this study, the wing area and the head part of the body should be designed to withstand the pressure greater than the body. It is shown that the sharp model B can withstand more pressure due to flow than the blunt model A.