• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.111-116
• /
• 2011

Three-dimensional finite element analyses have been performed to improve the durability of bulkhead. To keep pace with design changes and concentrate on regions of interest, SUBMODEL technique in ABAQUS was used for analysis. An analysis was conducted with following load cases: 1) Cap press-fit, 2) Bearing crush, 3) Bolt assembly, 4) Hot assembly, 5) Firing load, 6) Alternating firing load, 7) 2nd hot assembly. Fatigue analysis was done using commercial software FEMFAT and fatigue factors at the interested regions such as bolt tip area, counter bore, breathing hole, honing clearance were calculated and compared to aid design validation. Finite element modeling in the area of thread engagement used a simple constraint equations. Increasing bolt length, to a minimum of 39 mm above joint face gives a better fatigue resistance to the bulkhead. Breathing hole helps not only circulate the air in the crankcase but also fatigue resistance of bulkhead by relieving the stress at the critical locations.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.4
• /
• pp.69-74
• /
• 2014

A waste gate valve (WGV) assembly for a gasoline turbocharger is typically manufactured by means of precision casting. In this study, however, it was newly manufactured in a more innovative way, metal injection molding (MIM) using Inconel 713C alloy, and its performance was tested in a 1.6L direct injection gasoline engine by a thermal shock durability test that lasted 300 hours, after which the results were compared to those of a precision-cast WGV assembly with regard to the engine intake boost pressure, turbine wheel speed, and transient intake pressure. It was found that the two WGV assemblies showed similar performance levels throughout the durability test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.28-38
• /
• 2003

Finite element analysis of cylinder heat/block compound under assembly, thermal and firing condition were performed. FE model including two cylinders with gasket, head bolts, liners and valve seats was used. FE modeling method and boundary conditions were introduced. Stress distribution and deformation of cylinder head and block under each loading condition were presented. Gasket pressure distribution and bore distortion level were predicted. Measured data of bore distortion was compared with the analysis results. The analysis result showed similar trends with the experimental data. High cycle fatigue analysis on the basis of this result has been performed in order to find the critical areas of the engine assembly.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.657-661
• /
• 2019

The automobile industry is representative industry of complex characteristics, which employing 10 million people, the largest manufacturing industry over $1 trillion in sales and assembling with 20,000 parts to make complete automobile and automobile assembly processes have a lower automation rate than other processes, which is labor intensive processes of assembling to painted body with 3,000 components such as seats, built-in, instrument panel, glass, engine, transmission units. However, the current assembly process does not have real-time monitoring. If a tool position tracking system is adapted to assembly process for directing consistent work order and checking for missing work, the productivity and quality improvement of the assembly process can be achieved by preemptively preventing possible defects in the assembly process. So, this paper aims to develop a Tool Position tracking system using UWB(Ultra Wide Band) with trilateration and proves their effectiveness for real-time monitoring of automotive assembly process.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.571-575
• /
• 2008

An engine cradle is a quite important structural assembly for supporting the engine, suspension and steering parts of vehicle and absorbing the vibrations during the drive and the shock in the car crash. Recently, the engine cradle having structural stiffness enough to support the surrounding parts and absorbing the shock of collision has been widely used. The hydroforming technology may cause many advantages to automotive applications in terms of better structural integrity of parts, reduction of production cost, weight reduction, material saving, reduction in the number of joining processes and improvement of reliability. We focus on increasing the durability and the dynamic performance of engine cradle. For realizing this objective, several optimization design techniques such as shape, size, and topology optimization are performed. This optimization scheme based on the sensitivity can provide distinguished performance improvement in using hydroforming.

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.527-534
• /
• 2006

Modern passenger cars with diesel engines are equipped with DOC(diesel oxidation catalyst) for the purpose of reducing HC and CO in the exhaust stream. Cold start exhaust emissions pose troubles here as on gasoline engine vehicles. As a result, some of the diesel passenger cars roll off todays the assembly lines with WCC(warm-up catalytic converter). Oxidation characteristics of the particulates in WCC is analyzed in this study by EEPS(engine exhaust particulate size spectrometer). The maximum number of PM is found to come out of WCC in sizes near 10nm when an HSDI diesel engine is operated under the conditions of high speed and medium to heavy load. When the temperature of the WCC exceeds $300^{\circ}C$, the number of PM smaller than 30 nm in diameter sharply increases upon passing through the WCC. Total mass of emitted PM gets reduced downstream of the WCC under low speed and light load conditions due to adsorption of PM onto the catalyst. Under conditions of high speed and medium to heavy load, the relatively large PM shrink or break into fine particles during oxidation process within the WCC, which results in more mass fraction of fine particles downstream of the WCC.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.39-48
• /
• 2005

Finite element analyses have been performed for the purpose of obtaining the robust and reliable design of engine cylinder block. Fatigue under high cycle operating loads is a primary concern and is evaluated by a probabilistic method. The robust and reliable design by a probabilistic method can provide satisfactory design conditions for the performance of the system under the influence of noise factors. Therefore, the design by this method will be desensitized to the uncontrollable noise factors. The simple methodology evaluates the distortion of main bore is proposed for the purpose of maintaining a well-controlled clearance between the crankshaft and main bores. The proposed methodology has proven a capability of predicting the distortion of the main bore under assembly, thermal, and firing loads. The calculated results are correlated well with the experimental ones.

• Journal of the Korea Society for Simulation
• /
• v.17 no.2
• /
• pp.1-12
• /
• 2008

The major components of an engine are the cylinder block, cylinder head, crankshaft, connecting rod, and camshaft, which are more popularly known as the 5 C's. Thus, the engine shop usually consists of six sub-lines, including five machining lines and one assembly line. The flow line is the typical concept of the layout when the engineer designs the engine shop. This paper introduces a simulation study regarding the new crankshaft machining line in a Korean automotive factory. The major factors for designing the machining line are considered, and their effects on the system performance are evaluated with a three-dimensional(3D) simulation model that is developed with $QUEST^{(R)}$. The initial layout is analyzed using the simulation model, and we suggest some ideas for improvement.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.83-92
• /
• 2005

A piston assembly is very important because it directly receives the energy generated during combustion process. Surely, the friction and lubrication of piston-ring pack do an important role in the performance and fuel economy of an engine. In fact, the friction loss in piston-ring pack is the biggest portion to the whole engine friction. Therefore, the improvement of lubrication quality and friction loss in piston-ring pack will be directly related with the improvement in the performance and fuel economy of an engine. Meanwhile, the oil consumption and blow-by gas through piston-cylinder-ring crevices have to be controlled as less as possible. In these two aspects, the study on the optimized design of piston-ring pack has to be carried out. In this study, for the efficient design of piston-ring pack, it is focused to develop a basic computer program that predicts the inter-ring pressure, the motion of ring and the blow-by gas through a crevice volume model between adjacent rings, and the oil film thickness and the friction computed by lubrication theories.

• Journal of the Korean Institute of Gas
• /
• v.21 no.2
• /
• pp.26-31
• /
• 2017

The purpose of this paper is to study for turbocharger system in a vehicle of diesel engine. The first example, it certified the fact that a car engine is not to accelerate by clogged the exhaust tube as the turbine was damaged because of turbine wheel broken. The a vehicle with turbocharger must to stop engine operation after maintaining the appropriate idle revolution as it can be the sticking phenomenon if the operator immediately stop the engine being high revolution. The second example, it knew the phenomenon of acceleration faulty that the rod of VGT actuator that operating the turbocharger adhered with the bracket of VGT. The third example, it confirmed the power insufficiency phenomenon when driving by of alternator resistor and fan intercooler fan relay connector mistaken assembly. Therefore, the operator have to scrutinize manage no the failure of turbocharger system.