• Journal of Korean Institute of Industrial Engineers
• /
• v.35 no.2
• /
• pp.141-149
• /
• 2009

As the number of personal computers installed in vehicles increases, a touchpad often used in a labtop computer can be used for the control of an in-vehicle information system (IVIS). Using a touchpad to control the system allows the user to select among large amount of information with a single touch of dragging. For safety and convenience of a driver, the touchpad could be placed on a steering wheel. This research is designed to calculate the most efficient Control-Response Ratio (C/R ratio) for the menu interaction of a touchpad on a steering wheel. Since the menu pointer's rate of movement and proper C/R ratio is determined by the amount of selected information, the amount of displayed information and the movement of a menu pointer was chosen to be independent variables. The dependent variables are a user's preference and task completion time. Two factor full factorial within subject design was used 16 subjects. The investigation revealed that the amount of selected information increased with increasing C/R ratio. The movement of the pointer became slower as the amount of information increased. The best C/R ratio was calculated for each amount of information and preference regression of the user's preference was drawn accordingly. Through this research, the automobile interior designer can benefit from the guidelines suggested for the touchpad control.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.8
• /
• pp.3326-3333
• /
• 2012

In this paper, an educational simulator of automobile chassis electronic control system was developed. The developed system is composed of three parts, a driving condition control & monitoring system, a chassis electronic system monitoring & analysis system, and a virtual simulator & educational multimedia contents. The driving condition control & monitoring system has a commercial real car simulator, hydraulic equipments for representing driving conditions, and a remote control and monitoring system. In the chassis electronic system monitoring & analysis system, information of various sensors and actuators applied to the system can be monitored by Labview programs. Finally, the suggested virtual simulator and the multimedia with 2D Flash and 3D animations can be used effectively by means of teaching materials.

• KIPS Transactions on Software and Data Engineering
• /
• v.3 no.6
• /
• pp.201-214
• /
• 2014

In this paper, we propose a test case generation method adequate to destructive test of the BLDC(Brush Less Direct Current) motor controller used for the MDPS(Motor Driven Power Steering) system embedded in an automobile. The proposed method is a modified CTM(Classification Tree Method). CTM generates test cases assuming that all inputs are equally important. Therefore, it is very hard to generate test cases for extreme situations. To overcome the drawback and generate test cases specialized for destructive test. a modified CTM that compensates the limitation of traditional CTM is proposed. The proposed method has an advantage that it can intensively generate the test scenarios adequate to extreme situations by combining the test cases generated by the transitional CTM the while keeping the merit of the traditional CTM. The test scenarios for destructive test for the MDPS system embedded in a commercial automobile are generated utilizing the proposed method. The effectiveness of the proposed algorithm is verified through the test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.123-130
• /
• 2004

The automobile suspension system is composed of parts that affect performances of a vehicle such as ride quality, handling characteristics, straight performance and steering effort, etc. Moreover, by using the finite element analysis the cost for the initial design step can be decreased. In the design of a suspension system, usually system vibration and structural rigidity must be considered simultaneously to satisfy dynamic and static requirements simultaneously. In this paper, we consider the weight reduction and the increase of the first eigen-frequency of a suspension part, the upper control arm, especially using topology optimization and size optimization. Firstly, we obtain the initial design to maximize the first eigen-frequency using topology optimization. Then, we apply the multi-objective parameter optimization method to satisfy both the weight reduction and the increase of the first eigen-frequency. The design variables are varying during the optimization process for the multi-objective. Therefore, we can obtain the deterministic values of the design variables not only to satisfy the terms of variation limits but also to optimize the two design objectives at the same time. Finally, we have executed reliability based optimal design on the upper control arm using the Monte-Carlo method with importance sampling method for the optimal design result with 98％ reliability.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.3
• /
• pp.96-101
• /
• 2013

Automotive brake system is an essential element for the safety. The system is powered by the circulation of brake oil. A braker hose is used for the circulation of the oil in this system. Layout of the hose changes according to the steering and stress occur in the hose. A lot of the durability tests are performed in order to prevent serious problems such as hose bursting by the accumulation of the stress before setting an optimized hose layout on automobile. The test is conducted for the layout which is same such as set in automobile. In the test, brake hose layout shall exercise the same mode of thousands of times under the high temperature and periodic pressure condition and then the damage of the tested hose is inspected. This test, however, has a disadvantage of heavy consumption of time and money. In order to compensate for these drawbacks, the finite element method(FEM) study was performed to predict the changes in the layout of the brake hose. In this study, the FEM results and the test results were compared and the validity was verified. The radius of curvature of the FEM and test at the same positions were especially investigated for the validation. Also, this study will be used as the basis of research on the life prediction of brake hose.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.4
• /
• pp.301-308
• /
• 2006

Today's automobiles are changing into miniaturization and light weight for saving natural resources and energies. In order to raise the sufficiency of fuel consumption, new mechanism and components are required. Therefore, the expectations on the new materials are very high. Especially, Al materials are widely used to reduce the motors weight. Al using in automobiles is mostly casting material, and the material is developing rapidly in step with technical innovation. Al die casting has become an important field, as we are turning today's motor into light weight. One of the parts in steering system, valve housing, plays a role to reduce the operating effort of drivers. If valve housing being a part of steering system is produced by gravity casting, the space that manufacturing equipments are installed will be increased, and more energies and workers will be needed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.209-218
• /
• 2002

A V belt pulley is widely used in automotive industry. More than tow pulleys in one automobile are used, such items as crankshaft, water pump, air-con compressor and power steering pump. Although the shape and usage of pulleys are very simple, the design evaluation of a pulley design is difficult because the load conditions and the installation environment are complicated. So, we formulated the design evaluation for the V belt pulley by using CAE system, which enables to develop a design automation system. By using this system, an engineer can evaluate a pulley design easily without any painstaking effort, such as consideration of the complicated loads and CAE activities. Also the system helps to accumulate the design experience of a company, which guides the optimum design based on experience.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.160-166
• /
• 2018

This paper proposes an advanced suspension system and reports its performance in the framework of the preview control algorithm based on the RPS (road profile sensing) system and MSD system with the multi-stage damping characteristics. Typical disturbance inputs that cause excessive vibration and steering instability of an automobile are irregular obstacles that protrude or sink into the road surface to be driven. The control performance can be improved if information on the existence and shape function of its obstacle is known. Based on the results of the previous study, advanced research that uses the actuating system has been processed to be commercialized practically. For this purpose, a switching algorithm between the control logic and the multi-stage damping system was developed and its connectivity is presented. To verify the applicability of an actual vehicle, the proposed control system was implemented in full vehicle models and simulations were performed. The proposed system using the 3-DS actuator system, which is applied for structural simplicity, can improve the ride comfort and steering stability. In addition, the results indicate the feasibility of the intelligently controlled suspension system.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.12
• /
• pp.157-164
• /
• 1995

Straight belvel gear is used mainly for steering system, final reduction and differential gear in the automobile. The more high load, high velocity driving bevel gear, the more unsafe and unpleasant. In thid study, we get a kinematic equation by modelling straight bevel gear pair with simple elastic system, the dynamic characteristic analysis about this system, we got the dynamic load factor of tooth surface. Comparing the value of dynamic load factor by calculation with the measured value of Terauchi's experimental results is similar. We think it useful to analysis the vibration and the noise of straight bevel gear in operation with the analytic method of dynamic load of straight bevel gear using in this study.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.33 no.3
• /
• pp.71-78
• /
• 2010

The end shape of tube for automobile power steering system has influence on the ability of performance. In this case study, we attempted to optimize the forming process of a small tube using Taguchi experimental design methodology. A preliminary experiment was conducted and four main control factors were selected. The experiment was set up as an $L_9(3^4)$ orthogonal array, and determined the optimal levels of the four factors through the analysis of the experimental results. As a result, the performance characteristic(close adhesion power) of the product was improved about 36%. In addition, the process capability index $C_{pk}$ is enhanced from 0.94 to 6.85.