• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.283-287
• /
• 1996

The exhaust noise reduction of automobile with the active muffler is experimentally investigated. The control algorithm is the filtered-x LMS algorithm and the inverse algorithm with the adaptive line enhancer. Also, the control efficiency is increased with synthesized second harmonic engine frequency. In the experiment, the active muffler is applied to the end of exhaust system in automobile and the control with on-line secondary path modeling method(inverse algorithm) is compared the control of off-line secondary path modeling method. As secondary path transfer functions are changed, the experimental results show that the control performance with on-line method is more efficient than that with off-line method in the exhaust noise reduction of automobile.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.1
• /
• pp.39-48
• /
• 2001

Fe-Cr-Al alloy has been studied for application in automobile muffler materials due to good corrosion and oxidation resistance. In order to develop the automobile muffler materials, corrosion behaviors of electron beam physical vapor deposition (EB-PVD) coated surface of muffler matericls of muffler materials were investigated using potentiostat. For 0.1M NaCl solution, corrosion potential and pitting potential of Fe-20Cr-10Al was higher than that of Fe-5Cr- 10Al samples. Especially, in the case of Ti and Nb coated samples, pitting potential increased remarkably compared with non-coated samples. For 0.1M $CaCl_2$ solution, Ti-coated Fe-20Cr-10Al showed remarkably improved pitting corrosion resistance in comparison with non-coated Fe-20Cr-10Al and Fe-5Cr-10Al. The number and size of pits were decreased in the case of Ti coated samples in the 0.1M NaCl and 0.1M $CaCl_2$ solution.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.365-370
• /
• 2000

This study represents effect to attain to the exhaust gas and the exhaust noise by the inner shapes of automobile muffler, and obtained optimization-data for the inner muffler shapes by the temperature variation of the exhaust gas in muffler. The results of noise show to decrease in order of model-1, 2 and 3 under that the engine speed is 3500 R.P.M and similar values beyond it. CO represented good the model-2 at low engine speed and model-1 at high engine speed. The model-3 was show to tiny variation difference by the variables. HC decrease mostly by increase of the engine speed and expressed low values the model-2 at 3,000 R.P.M and the model-1 at high speed. Wholly, the model-2 expressed stable results. The temperature distributions expressed high distributions by increase of the engine speed, and the model-3 was express most good among three models.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.190-196
• /
• 2014

Exhaust system by reinforcement of environment regulation came to the foe study necessity. And Exhaust system has necessary to increase the engine performance and silence. From this cause, Automobile has significantly considered production expense. this study makes process for checking the characteristics about Exhaust variable valve within muffler. Variable valve might reduce the baffle within muffler, It was possible to remove the front muffler. Therefor, To miniaturize a size of muffler might be increased by performance through cost-cutting effect and controling of back pressure. Because the Study on Variable valve installed within muffler, to measure the real data was hardly resulted one of the assignments. From manufactured conduct device, might measure data one of piece which was up-graded of problem. Considering to these point, stressed pressure distribution has analyzed on cross section, floating characteristics about velocity distribution around variable valve using analysis as computational fluid dynamics of Ansys with completed measurement data.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.350-356
• /
• 2011

In this paper, we proposed the automatic cutting mechanism of the perforation pipes in an automobile muffler. This cutting mechanism makes continuous work possible, because it performs the batch work via the sequential operation of loading, feeding, cutting, and discharging. The proposed cutting mechanism consists of the frame unit, escape unit, turning unit, feeding unit, vision system, clamping unit, spindle/cutting unit and cooling unit. And, these mechanisms have been modularized through mechanical, dynamical and structural optimized design using the SMO (SimDesigner Motion) analysis module. Also, the virtual prototype was carried out using the 3-D CAD program. The cutting process cycle is performed in the order of loading, vision processing, feeding, clamping, cutting and discharging. And the cycle time for cutting one piece was designed to be completed in four seconds.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.5 s.170
• /
• pp.138-143
• /
• 2005

Recently, automobile manufacturers regarding stability, economic environmental-friendly problems by the development of automobile, environmental problem as designing the exhaust system. Increasingly strict environmental regulations to lower fuel consumption and reduce emission. Also to reduce the noise and the vibration of the automobile. According to develop variable type muffler, dual muffler and active intelligence exhaust system unit. Improvement in engine performance and fuel consumption rate demand information of pressure fraction and heat characteristics. To be able to determine these factor for we experiment on each case of exhaust system unit. In this study, how back pressure is distributed in flow-through in exhaust system and how to design exhaust system flexibleness, efficiency and combustion charateristics influenced by back pressure. This study furnish basic data for engineers, technicians.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.6 s.171
• /
• pp.192-198
• /
• 2005

Recently, Automobile manufacturers regarding stability, economic environmental-friendly problems by the development of automobile. This reason is increasingly strict environmental regulations to lower fuel consumption and reduce emission. Designing more efficient and low emission control exhaust system results in more efficient Performance, reduced back Pressure and higher convert efficiency. Also to reduce the noise and the vibration of the automobile. According to develop variable type muffler, dual muffler and active intelligence exhaust system unit. Improvement in engine performance and fuel consumption rate, higher conversion efficiency demand information of pressure fraction and heat characteristics. To be able to determine these factor fur we experiment on each case of exhaust system unit. In this study, how back pressure is distributed in flow-through in exhaust system and how to design exhaust system flexibleness, efficiency, lower back pressure and optimal performance. This study furnish basic data for engineers, technicians.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.7 s.184
• /
• pp.108-113
• /
• 2006

Recently, Automobile manufactures have developing automotive exhaust system under consideration for improvement in engine performance. It thus develop many exhaust components. For example active muffler, semi-active muffler, electronic muffler etc. In this components consider enhanced back pressure and reduction noise. Especially, In recent years it develop the study of semi-active muffler. Semi-active muffler is simple structure and excel performance. Recently many forms semi-active muffler was developed and adopted to the actual use in consideration of cost and technical side for noise and vibration. This study had main objects about the recently developed the semi-active muffler. It was to show its combustion performance as well as its enhanced back pressure characteristics in design. Therefore if the precise analysis of the combustion pressure according to the back pressure transmission was carried out, it was understood that this study would be utilized in the design of the exhaust system such as the semi-active muffler.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.661-665
• /
• 2005

The muffler reducing the exhaust noise and vibration from the engine influence on the engine performance. Recently the semi-active muffler was developed and adopted to the actual use in consideration of the cost and technical side for noise and vibration. This study is about the recently developed semi-active muffler. This paper attempt to analyze the dynamic stress field on the gate plate by using the finite element methods. According to the analysis of the Exhaust Variable Valve, its spring has the most influence on its operation compare with effects of other components. The design parameters of the Exhaust Variable Valve such as the spring displacement, diameter, coil number, free angle and so forth were used.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.37-44
• /
• 2001

This study is focused on the development of a new muffler. A control valve installed in the exhaust system is operated by torsion springs, and its open angle is controlled automatically corresponding to the engine operating conditions. The experiments were done using an exhaust system simulator having the same pulsation wave frequency and similar pulsation propagation characteristics of a real exhaust system. The purpose of this study is to develop a new muffler system which has improved noise reduction quality and less power loss than conventional mufflers and electronic-control mufflers.