• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.2
• /
• pp.9-15
• /
• 2010

ADS-B(Automatic Dependent Surveillance-Broadcast) has been recognized as a key component of Surveillance and ATM in CNS/ATM System. In addition to providing surveillance for air traffic control(ATC), ADS-B also supports airborne applications such as enhanced traffic situational awareness through the display of other aircraft to pilots and flight crew. It provides the real-time and same air traffic information to pilots in the aircraft cockpit, air traffic controllers in tower and surface vehicles on the ground at the same time. Aircraft Cockpit Display Unit will display the given information precisely and accurately. This paper describes progress in the development of a Cockpit Display with ADS-B data that enable pilots to acquire, verify and maintain pre-defined spacing intervals from other aircraft for general aviation and small regional aircraft. The designed display provides analogous information in the form of traffic position, range, and ground speed, etc.

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.4
• /
• pp.1014-1025
• /
• 1996

The magnetizer that is magnetizing the magnet which is used for RGB (Red Green Blue) control of CRT(Cath-ode-Ray Tube)and the magnet inspection unit which is used for test the state of magnetizing have been imported by magnet manufactures up to now. They are operation by manual now, so that they are needed lots of time and have an increase in probability of malefunction by operator. In this study, we have developed a united system from the magnet production process to inspection ork to automaized a entire progress. Therefor, as we are testing the status of every work and analyzing exactly the distribution in quality with this system, we have known that the reliability of magnetization and magnetized status test has not only increased, but the rate of inferior quality almost not generated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.166-174
• /
• 2008

Recently, the automotive industry has been developing rapidly. With the progress parts of the automobile components need high quality and the reliability. Among them, braking unit is essential device, and acquire the reliability through the performance test of brake. This study was aimed to design the performance-test-bench to measure the drag torque which has effect on caliper in braking unit. In this progressive technology, it is vital importance to use hydraulic and pneumatic, and to combine test bench with instrumentation engineering technology. This system to construct the design of hydraulic and pneumatic circuit, interface technique between sensors and personal computer, data acquisition and display design, and integrated control are very important technology. Moreover, reliable data are obtained through vacuum system and hydraulic and pneumatic system by using of booster and brake master cylinder which are actually applied to automobile. Then, data signal detector sensors for speed, pressure and torque is attached on this system. Therefore, in this study, we designed a performance-test-bench by and we also made an total control system using personal computer which is more progressive and flexible method than existing PLC control.

• Journal of Korea Multimedia Society
• /
• v.22 no.11
• /
• pp.1269-1279
• /
• 2019

In medical image analysis, segmentation is considered as a vital process since it partitions an image into coherent parts and extracts interesting objects from the image. In this paper, we consider automatic segmentations of OCT retinal images to find six layer boundaries using convolutional neural networks. Segmenting retinal images by layer boundaries is very important in diagnosing and predicting progress of eye diseases including diabetic retinopathy, glaucoma, and AMD (age-related macular degeneration). We applied well-known CNN architecture for general image segmentation, called Segnet, U-net, and CNN-S into this problem. We also proposed a shortest path-based algorithm for finding the layer boundaries from the outputs of Segnet and U-net. We analysed their performance on public OCT image data set. The experimental results show that the Segnet combined with the proposed shortest path-based boundary finding algorithm outperforms other two networks.

• Journal of Environmental Science International
• /
• v.25 no.6
• /
• pp.897-904
• /
• 2016

We investigated the local climatological characteristics of the mountain adjacent the Dongyeong herb garden in Chilgok. We established one set of automatic weather system (AWS) on a hill where development of herb garden is in progress. The observations were continued for 2 years(2013. 07-2015.06). In this study, we analyzed the observed data comparing the data of Gumi meteorological observatory (GMO). The results showed that the air temperature(relative humidity) of Dongyeong herb garden were lower(higher) than those of GMO. Especially the differences are more during warm climate season. It means that the gaps of thermal environment between two points are mainly caused by the evaporation effects of forest. In addition, we analyzed the warmth indices(warmth index and coldness index) with the observed air temperature. The warmth and coldness indices indicate about 107 and -12, respectively. The values correspond to warm temperature climate.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.1
• /
• pp.21-24
• /
• 2005

The problem of fluctuation-induced digital errors in a rapid single flux quantum (RSFQ) circuit has been very important issue. So in this experiment, we calculated error rate of RSFQ switch in superconductiyity ALU, The RSFQ switch should have a very low error rate in the optimal bias. We prepared two circuits Placed in parallel. One was a 10 Josephson transmission lines (JTLs) connected in series, and the other was the same circuit but with an RSFQ switch placed in the middle of the 10 JTLs. We used a splitter to feed the same input signal to the both circuits. The outputs of the two circuits were compared with an RSFQ XOR to measure the error rate of the RSFQ switch. By using a computerized bit error rate test setup, we measured the bit error rate of 2.18$\times$$10^{12}$ when the bias to the RSFQ switch was 0.398mh that was quite off from the optimum bias of 0.6mA.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.8
• /
• pp.4209-4214
• /
• 2012

The current situation of cancer registration in China was systematically reviewed. So far, cancer registration in China has been making a great progress in the following aspects: the number of cancer registries and covered population have increased dramatically; a registration network has been established and completed gradually; regulations and rules improved remarkably; more attention is being paid by every level of government; a lot of registration software has been created and financial support ensured. However, we are still facing some problems and challenges, such as no stable groups of registrars, shortage of training opportunities, poor data quality, insufficient utilization and lack of multidisciplinary mechanisms, so that the cancer registration system still needs to be enhanced and improved. Along with the development of economy, science and information technology, methods and patterns of cancer registration is changing. It is to be expected that cancer registration will be automatic, nationwide and integrated with community healthcare in the near future.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.411-416
• /
• 2000

Cutting process has been automated by progress of CNC and CAD/CAM, but polishing process has been depended on only experiential knowledge of expert. To automate the polishing process, a polishing robot with w degrees of freedom which is attached to a machining center with 3 degrees of freedom has been developed. This automatic polishing robot is able to keep the polishing tool normal on the curved surface of die to improve a performance of polishing. Polishing task for a curved surface die demands repetitive operation and high precision, but conventional control algorithm can not cope with the problem of disturbance such as a change of load. In this research, a new sliding mode control algorithm is applied to the robot. The signal compression method is used to identify polishing robot system. to obtain an effect of 5 degrees of freedom motion, a synchronization between the machining center and polishing robot is accomplished by using M code of machining center. And also a trajectory for polishing the curved surface die by 5 degrees of freedom motion, a synchronization between the machining center and polishing robot is accomplished by using M code of machining center. And also a trajectory for polishing the curved surface die by 5 axes machining center is divided into data of two types for 3 axes machining center and 2 axes polishing robot. To evaluate polishing performance of the robot. various experiments are carried out.

• Journal of Korea Multimedia Society
• /
• v.13 no.3
• /
• pp.392-399
• /
• 2010

The Automobile has developed and changed through the years from the invention and increased human-being's scope of activity. Junction Box, one of the part of automobile, is inspected by human eyes which caused mistakes and slow progress. To achieve the speed and accuracy the system was compensated by vision system which is inspecting automatically. This paper is automatic inspection of fuse and relay which is inserted in the junction box by checking the color and pattern of the cover. After checking the performance of the system by using the junction box, the result was 100 percent perception and open the possibility to inspect junction box fast and easy and accurate if it is applied to the industry.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.810-814
• /
• 1996

The purpose of this exclusive welding-machine process using the welding Torch-rotation form is to develop a mechanism which can solve the problem of twisted welding wires and cables. The technique was developed by revising the torch position and smooth controlling of both the formal and reverse rotation. Some of the advantages of using the Torch-rotation form over the Work-rotation technique are the practical uses of increased work space and link work with the automation system of the plant. Using this welding machine process, It is possible to design a specific tool in order to solve the implemental problem. And I produced a control plate which can manipulate the progress of the entire process at the work place. Even if another kind of axle casing's welding work is used this process can be utilized if the fixed tip and work is produced and changed. The development if this exclusive welding-machine could reduce the manpower of skilled welding labor and after considerable analysis, this machine was found to increase productivity and better quality product in comparison to the handmade product.