• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2145-2147
• /
• 1998

This paper presents a Class-D type switched mode audio power amplifier employing ZVT(Zero-Voltage-Transition) soft switching technique. In order to obtain a wide bandwidth and lower distortion for an audio amplifier a high switching frequency is essential. The ZVT switching scheme enables a high frequency switching without sacrificing the efficiency much as in a hard switching. A prototype amplifier is built to demonstrate the feasibility of this technique for the audio power amplifier.

• 전기의세계
• /
• v.29 no.12
• /
• pp.798-803
• /
• 1980

A computer program for noise analysis of the audio circuit is developed. The application of the program to the equalizer, low frequency amplifier of radio circuit and cascaded amplifier show good results. The general noise analysis method for cascade operational amplifier is presented. The noise spectral power density is calculated for a resonator active filter.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.605-607
• /
• 2004

A class D digital audio amplifier with small size, low cost, and high quality is positively necessary in the multimedia era made of home theater system and the digital audio broadcasting (DAB). It is impossible to analyze the stability of the digital audio amplifier, which is based on the PWM signal processing. To solve this problem, the digital audio amplifier is analyzed using variable structure control theory which is one of nonlinear system theories. Moreover, the magnitude and the frequency of ripple signal, which generated by hysteresis in the comparator, is obtained using describing function which is useful to represent the input-output relation of nonlinear system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.4
• /
• pp.385-391
• /
• 2007

A class D digital audio amplifier with small size, low cost, and high quality is positively necessary in the multimedia era. Since the digital audio amplifier is based on the PWM signal processing, it is improper to analyze the principle of signal generation using linear system theories. In this paper, a class D digital audio amplifier based ADSM (Advanced Delta-Sigma Modulation) is considered. We first model the digital audio amplifier and then explain the operation principle using variable structure control algorithm. Moreover, the ripple signal generated by the hysteresis in the comparator has a significant effect on the system performance. Thus, we present a method to find the magnitude and the frequency of the ripple signal using describing function. Finally, simulations and experiments are provided to show the validity of the proposed methods.

• Journal of Korea Multimedia Society
• /
• v.20 no.9
• /
• pp.1551-1558
• /
• 2017

Audio power amplifiers have been designed based on the premise that the impedance of loudspeakers is fixed at nominal 4 ohms or 8 ohms. However, it is known that the impedance varies with frequency and takes on the nominal value at some limited frequencies. The principle of the loudspeaker operation reveals that the sound pressure produced by the loudspeaker is proportional to the current flowing in the voice coil, not the voltage between the two terminals. We take the characteristics of the loudspeaker into account and compare the frequency responses of the loudspeaker in voltage-drive mode and current-drive mode via computer simulations, to conclude that the audio amplifier drive mode should be re-considered in an effort to improve the sound quality.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.109-116
• /
• 2014

This paper presents a high-efficiency digital class-D audio amplifier using a composite interpolation filter for portable audio devices. The proposed audio amplifier is composed of an interpolation filter, a delta-sigma modulator, and a class-D output stage. To reduce power consumption, the designed interpolation filter has an optimized composite structure that uses a direct-form symmetric and Lagrange FIR filters. Compared to the filters with homogeneous structures, the hardware cost and complexity are reduced by about half by the optimization. The coefficients of the digital delta-sigma modulator are also optimized for low power consumption. The class-D output stage has gate driver circuits to reduce shoot-through current. The implemented class-D audio amplifier exhibited a high efficiency of 87.8 % with an output power of 57 mW at a load impedance of $16{\Omega}$ and a power supply voltage of 1.8 V. An outstanding signal-to-noise ratio of 90 dB and a total harmonic distortion plus noise of 0.03 % are achieved for a single-tone input signal with a frequency of 1 kHz.

• Journal of Korea Multimedia Society
• /
• v.21 no.9
• /
• pp.1068-1075
• /
• 2018

We propose a method for driving loudspeakers from class D audio power amplifiers in current mode, instead of in conventional voltage mode, which was impossible with the feedback circuitry. Unlike analog audio amplifiers, Class D audio power amplifiers have signal delay between the input and output signals, which makes it difficult to apply the feedback circuitry for current-mode driving. The idea of the pre-distortion scheme used for the compensation of the non-linearity of RF power amplifiers is adapted to remedy the impedance variation effect of the loudspeakers for current driving. The method uses the speaker model for the pre-distorter to compensate for the speaker impedance variation with frequency. The simulation and test results confirms the validity of the proposed method.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.10 no.2
• /
• pp.23-35
• /
• 1973

To deal with electronic circuits analysis, the matrix-topological formulation is described. In addition to the classical mesh, node and outset method, a mixed analysis is described, and it is presented that any electronic circuits problem, including dc, ac, transient anatysis, can be analysed by the electronic circuit analysis program. In this paper a model of two stage transistor audio amplifier is made and frequency characteristics for the cicuits are analysed by ECAP. The measured results give good agreement with the ECAP analysis.

• International Journal of Internet, Broadcasting and Communication
• /
• v.9 no.2
• /
• pp.58-63
• /
• 2017

The sound we hear is transmitted through the atmosphere. However, both the sound we want to hear and the surrounding sound are mixed, and noise is generated, and the sound is not clearly transmitted due to factors such as distance. In particular, in closed spaces like buildings, it is often difficult to hear sounds from outside because of the sound of reflection. People with hearing impairments, such as the elderly and the deaf, have a hard time hearing the sounds they want to hear. Thus, we are developing a hearing aid that can detect radio waves. To this end, we propose the development of a hearing aid that uses FM radio and Bluetooth. These devices are expected to be useful not only for the elderly and the deaf but also in situations where information is transmitted to a large number of people, such as students and tourists, in a large space. The main purpose of this device is to enable users to hear sound correctly without blind spots.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.2 no.1
• /
• pp.35-42
• /
• 1977

An analysis has been made about the performance of the switching-mode amplifier which can improve its efficiency higher than class C in audio amplification, and the improvement of characteristics and constitution in using it for modulator circuits was considered. As a result, the linearity of modulation up to 97% and the frequency response keeping flat up to 7, 200Hz have been observed.