Ball grid array (BGA) substrate 상의 0.5 $\mu\textrm{m}$Au/5 $\mu\textrm{m}$Ni/Cu 층으로 구성된 접촉 패드(pad)와 In-15(wt.%)Pb-5Ag 솔더 볼 사이에서 리플로우 및 고상 시효동안 일어나는 금속학적 반응 특성이 조사되었다. 1-5 분의 리플로우 시간에 따라 솔더/패드 계면에서 $AuIn_2$ 또는 Ni-In 금속간 화합물층이 형성됨이 관찰되었다. 리플로우 동안 용융 In-l5Pb-5Ag 솔더 내로의 Au 층의 용해 속도는 $2\times 10^{-3}$$\mu\textrm{m}$/sec 정도로 측정되어 공정 Sn-37Pb와 비교하여 매우 느린 것으로 관찰되었다. $130^{\circ}C$에서 500시간의 고상 시효 후에는 초기 리플로우 시간에 관계없이 $Ni_{28}In_{72}$ 금속간 화합물층이 약 3 $\mu\textrm{m}$까지 성장하였다. 이를 통하여 솔더 합금에서의 In 원자들은 아래의 Ni 층과 반응하기 위하여 리플로우 동안 형성된 $AuIn_2$상을 통하여 확산하는 것으로 관찰되었다. 미세구조 관찰과 전단 시험을 통하여 In-l5Pb-5Ag합금의 경우는 Sn-37Pb 조성과는 달리 Au/Ni surface finish 상에 사용시에도 솔더 접합부에서의 Au-embrittlement를 야기 시키지 않는 것으로 분석되었다.
This study was performed to observe the microhardness change of the surface and the bonding strength between the porcelain and alloy specimens in order to investigate the effects of appended indium, tin and copper on interfacial properties of Au-Pd-Ag alloys. The hardness of castings was measured with a micro-Vicker's hardness tester. The interfacial shear bonding strength between alloy specimen and fused porcelain was measured with a mechanical testing system(MTS 858.20). The microhardness of Au-Pd-Ag alloy was increased by adding indium and tin, but not increased by adding copper. The shear bonding strength of Au-Pd-Ag-Sn alloy and Au-Pd-Ag-Cu alloy showed 87MPa, 57MPa. The higher concentration of adding elements showed the higher shear bonding strength.
The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.
Microstructure and shear strength of Sn-Zn lead-free solders and Au/Ni/Cu UBM joint under thermal aging conditions was investigated. The samples were aged isothermally at 10$0^{\circ}C$ and 15$0^{\circ}C$ for 300, 600, and 900 hours. The IMCs(Intermetallic Compound) at the interface between solder and UBM were examined by FESEM and TEM. The results showed that the shear strength was decreased with aging time and temperature. The solder ball with high activated RA flux had about 8.2% higher shear strength than that of RMA flux. Poor wetting and many voids were observed in the fractured solder joint with of RMA flux. The decreased shear strengths were caused by IMC growth and Zn grain coarsening. Zn reacted with Au and then was transformed to the $\beta$ -AuZn compound. Although AuZn grew first, $r-Ni_5Zn_{21}$ compounds were formed with aging time. The layers indicated by $Ni_5Zn_{21}(1)$, (2), and (3) were formed with the thickness of ∼0.7 ${\mu}{\textrm}{m}$, ∼4 ${\mu}{\textrm}{m}$, and ∼2 ${\mu}{\textrm}{m}$, respectively.
최근의 전자부품은 고밀도 고집적화 됨에 따라 여러 가지 문제점들이 발생되고 있다. 그 중 부품이 실장되는 부분에 사용되는 솔더나 전기적 회로를 구성하는 패턴간에 금속 이온 마이그레이션(Metallic Ion Migration)이 발생하여 전기적 단락(Short)를 유발함으로써 전자제품의 치명적 고장을 유발한다. 본 연구는 이온 마이그레이션 현상을 물방울시험(Water Drop Test)을 통하여 재현함으로써 발생 메카니즘을 확인하여 발생원인을 직접적으로 관찰하고, 각 종 패턴의 거리 및 전압에 따른 발생속도의 차이를 조사하기 위하여 수행되었다. 이러한 실험을 위하여 콤 패턴(Comb Pattern)의 FR-4 재질 인쇄회로기판(PCB : Printed Circuit Board)을 사용하였으며, 사용된 전극재질로는 Cu, SnPb, Au를 사용하였고, 패턴간 거리는 0.5, 1.0, 2.0mm의 3가지 종류로 구분하였다. 또한 패턴간에 인간 된 전압은 6.5V, 15V를 인가한 후 마이그레이션이 발생되는 시간을 측정하였다. 이러한 실험으로부터 다음과 같은 결론을 얻었다. (1) 6.5V의 인가전압에서는 Cu 패턴이 대체적으로 가장 빠르게 마이그레이션이 발생하였으며, 다음으로 Au가 발생하였고, Cu와 SnPb의 발생시간은 대체적으로 근사한 값을 나타내었다. 이것은 비슷한 평형전위를 갖는 재료는 마이그레이션 발생시간이 유사하게 나타나며, 높은 (+)전위를 갖을수록 발생시간이 지연됨을 알 수 있다. (2) 15V를 인가하였을 때 패턴간격이 0.5mm인 경우 Cu, Au, SnPb의 순으로 나타났으며, 1.0mm는 SnPb, Cu, Au, 2.0mm인 경우는 SnPb, Au, Cu의 순으로 마이그레이션이 발생하였다. 인가전압이 높은 경우 초기 발생에는 큰 차이가 없지만 수지상이 발생 후 성장하는데 많은 영향을 미치는 것으로 보인다. 이것은 초기 수지상의 형성에 큰 영향을 미치는 것은 재료의 평형전위에 의한 값이 좌우하지만, 수지상이 일정길이 이상 형성된 이후에는 성장속도가 평형전위에 따른 값과는 다소 다르게 나타남을 알 수 있다.
This paper presents that the affecting factors to the solderability and initial reliability. It is the factor that the coefficient of thermal expansion between package and PCB(Printed Circuit Board), the quantity of solder paste and reflow condition, and Au thickness of the solder ball pad on polyimide tape. As the reflow soldering condition for 48 ${\mu}BGA$ is changed, it is estimated that the quantity of Au diffusion at eutectic Sn-Pb solder surface and initial bonding strength of eutectic Sn-Pb solder and lead free solder. It is the result that quantitative measurement of Au diffusion quantity is difficult, but the shear strength of eutectic Sn-Pb solder joint is 842 mN at first reflow and increases 879 mN at third reflow. The major failure mode in solder is judged solder fracture. So, Au diffusion quantity is more affected by reflow temperature than by the reflow times.
Three different kinds of substrate used in this study : bare Cu, electroless Ni/Cu substrate with a Nilayer thickness of $5\mu\textrm{m}$, immersion Au/electroless Ni/Cu substrate with the Au and Ni layer of $0.15\mu\textrm{m}$ and $5\mu\textrm{m}$ thickness, respectively. The wettability and interfacial tension between various substrate and Sn-3.5Ag solder were examined as a function of soldering temperature, types of flux. The wettability of Sn-3.5Ag solder increased with soldering temperature and solid content of flux. The wettability of Sn-3.5Ag solder was affected by the substrate metal finish used, i.e., nickel, gold and copper. Intermetallic compound formation between liquid solder and substrate reduced the interfacial energy and decreased wettability.
플립칩 전자패키지에서 칩과 기판(PCB)를 연결할 때, 통상적으로 칩쪽은 금속패드/UBM 처리를 기판 쪽은 표면처리를 한 후 솔더로 연결하는데, 이 때 사용되는 UBM이나 표면처리에 따라, 칩/솔더, PCB/솔더에 생성되는 금속간 화합물의 종류와 두께 및 솔더의 조성이 변하게 되어 궁극적으로 솔더 접합부의 기계적 신뢰성에 영향을 주게 된다. 본 연구에서는 Cu와 Au/Ni의 두가지 금속 패드가 무연솔더의 저주기 피로특성에 어떠한 영향을 미치는 지에 대해 고찰해 보았다. 저주기 피로 실험은 Cu나 Au/Ni이 표면처리 된 기판에 무연솔더 (Sn-3.5Ag, Sn-3.5Ag-1.5Cu, Sn-3.5Ag-XBi(X=2.5, 7.5), Sn-0.7Cu)를 리플로하여 총변위를 변화시키면서 상온에서 시행하였다. 기판의 표면처리에 관계없이 Sn-3.5Ag, Sn-3.5Ag-XCu(X-0.75, 1.5), Sn-0.7Cu 합금이 Sn-3.5Ag-7.5Bi 합금보다 피로저항성이 현격히 좋았으며, Au/Ni 표면처리한 솔더 접합부가 Cu 처리한 경우보다 피로저항성이 뛰어난 것으로 나타났다. 파괴 후 단면을 조사한 결과 계면에 형성된 금속간 화합물 내에 미세균열이 발견되었는데, Cu 표면처리를 사용한 경우 더 많은 미세균열이 생성된 것을 볼 수 있었다. Sn-3.5Ag, Sn-3.5Ag-Cu(X=0.75, 1.5), Sn-0.7Cu 합금의 경우 금속간 화합물 내에 생기는 미세 균열이 거시 균열로 성장하지 않고 파단은 항상 솔더 내부로 일어난 반면. Bi를 함유한 솔더의 경우, 기판의 표면처리에 상관없이 금속간 화합물/솔더 계면으로 균열이 생성 진전되어 다른 솔더합금에 비해 열악한 피로저항성을 나타내는 것으로 보인다. 이것은 Bi의 금속간화 합물/솔더 입계 편석이나 Bi 합금이 다른 합금에 비해 높은 경도값을 가지는 것에 인한 것으로 보여 진다.
공침법을 이용하여 Ca 및 Pt 가 첨가된 $SnO_{2}$ 미세 분말을 제조하였다. 제조한 미세분말에 대해 TEM, XRD 및 BET 분석으로 결정크기 및 비표면적을 분석하였으며, 제조한 원료분말을 이용하여 스크린 인쇄법으로 후막형 가스 감지 소자를 제작하고, 그 특성과 탄화수소계가스에 대한 감지 특성을 조사하였다. 첨가된 Ca 및 Pt에 의해 하소와 소성의 열처리 과정 중에 $SnO_{2}$ 결정 성장이 억제되었으며, 탄화수소계가스에 대한 응답특성의 향상을 가져왔다. 한편, 소자의 전극으로써 Au 와 Pt를 사용하여 비교 분석하였는데, Au를 전극으로 사용할 경우에 Pt에 비해 가스 감응 특성 면에서 큰 저하를 가져왔다. 이는 Pt 전극도 $CH_{4}$의 산화에 기여했기 때문이다. Ca 및 Pt를 각각 0.1, 1 wt% 첨가한 $SnO_{2}$ 후막소자의 경우 2000 ppm의 $CH_{4}$에 대해 약 83%의 감도를 보였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.