• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2567-2572
• /
• 2007

The suppression of fluid force acting on a square prism near plane wall was studied by attaching fences on the corners of the prism. The height of the fence was 10% of the square width and the range of Reynolds number considered was Re=$2.0{\times}10^4$. The experimental parameters were the attaching position and numbers of fences, the space ratios G/B(G/B=0.1${\sim}$1.2) between prism and plane wall. The average drag coefficients were increased and the average lift coefficients were decreased and increased with the space ratios toward plane wall. The drag of the prism was reduced average 7.6% with the space ratios by attaching the normal fence at the rear and upper corner and the horizontal normal fence at the rear and lower corner on the prism. In this case, the separated flow at the front and upper corner was reattached on the upper side of the prism and the vortex streets between the prism and plane wall were appeared more slowly than that of prism without fences.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.219-230
• /
• 1995

The flow characteristics of a two-dimensional offset jet issuing parallel to a rough wall is experimentally investigated by using a split film probe with the modified Stock's calibration method. The mean velocity and turbulent stresses profiles in the up and down-stream locations of the wall-attachment regions are measured and compared with those of the smooth wall attaching offset jet cases. It is found that the wall-attachment region on the rough wall is wider than on the smooth wall for the same offset height and the jet speed. The position of the maximum velocity point is farther away from the wall than that for the smooth wall case because of the thick wall boundary layer established by the surface roughness. It is concluded that the roughness of the wall accelerates the relaxation process to a redeveloped plane wall jet and produces a quite different turbulent diffusion behavior especially near the wall from comparing with the smooth plane wall jet turbulence.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.776-781
• /
• 2008

In this study, ubiquitous health care system attaching in chair to monitor ECG for health care was developed at the unconsciousness state. The system conveniently and simple measured ECG at non-consciousness. We measured the contact impedance to skin-electrode of metal mesh electrodes of the system. Contact impedance enable the electrode to use for ECG measurement. The results are that the impedance of the metal mesh electrodes according to sizes is low when the size is 4$cm^2$. As the result, when the size of the metal mesh electrode is 4$cm^2$, the electrode is fit for ECG measurement. We can acquired by positing the arm on the metal mesh electrode. The ECG signal was detected using a high-input-impedance bio-amplifier, and then passed filter circuitry. The measured signal transmitted to a PC through the bluetooth wireless communication and monitored. Data of the non-constrained ECG system attaching in chair is noise-data when comparing metal mesh electrode with the Ag/Agcl electrode but the data is significant to monitor ECG for check the body state.

• Journal of Korean Association for Spatial Structures
• /
• v.13 no.3
• /
• pp.73-81
• /
• 2013

In paper after the strong earthquake of recently the Korea neighborhood, the Korean government survey show that the 86% of school buildings in Korea are in potential damage risk and only 14% of them are designed as earthquake-resistance buildings. Earthquake Reinforcing projects of school have been a leading by the ministry of education, however their reinforcing methods done by not proved a engineering by experiment which results in uneconomical and uneffective rehabilitation for the future earthquake. An experimental and analytical study have been conducted for the shear reinforcing method of column by axis and horizontal axis load using attaching composite beam. Based on the previous research, in this study, Design examples are given to show the performance evaluation for the column reinforcing of old school buildings using nonlinear analysis is going to be conducted and strengthening method is going to be on the market after their performance is proved by the test.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.10
• /
• pp.3304-3312
• /
• 1996

An experimental study on the convective heat transfer characteristics was performed for a two-dimensional wall attaching offset jet(WAOJ). Thermochromic liquid crystal was used to measure the plate wall temperature. The Nusselt number was measured for Reynolds numbers from 6, 500 to 39, 000, and the offset ratios from 0.5 to 15. The maximum Nusselt number point coincides with the time-averaged reattachment point and Nusselt number decreases monotonically after the jet reattaches on the wall. In the recirculation region Nusselt number minimize near the upstream corner and then increases as X/D decreases to vanishes. This suggests the existence of secondary vortices, causing an additional mixing of the flow in the corner. The correlations between the local Nusselt number and Reynolds number, Re, offset ratio, H/D, and streamwise distance, X/D are presented.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.910-913
• /
• 2009

This paper examines attaching speed, detaching speed and contact time which affected in the ink transfer ratio and presents the best conditions for fabrication process of electrodes with Ag-ink using microcontact printing method. In conclusion, it shows the best printing characteristic by two conditions. One of condition is the attaching speed have to within less than 1mm/s and the detaching speed is high velocity as 1000mm/s and the contact time is taken about the minimum time when inking process. Another condition is the attaching speed have to within more than 100mm/s and the detaching speed have to within less than 1mm/s and the contact time is longer than 30second when the printing process. As using these condition and the stamp sized 5cm${\times}$5cm, it was possible for printing equally until $30{\mu}m$ of width. The printed thickness of a electrode was about 300 to 500 nm, the surface roughness was about dozens nm under 50 nm.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.30-36
• /
• 2014

Many different cells types have been found to be highly sensitive to mechanical force imposed by their surroundings. The cellular response to external mechanical forces has very important effects on numerous biological phenomena. In spite of its importance in biological processes, the cell adhesion force remains difficult to measure quantitatively at the cellular level. In this paper, to enhance quantitative measurements of cell adhesive interactions, a new attaching system and a method in which a glass bead can be attached to an AFM cantilever was designed and fabricated, and the degree of range displacement was controlled in the system. In an experiment, the movement of the stage in the attaching system and the attaching process were measured. The effectiveness of this system was confirmed as well in the experiment. In addition, through a commercial AFM system, the spring constant of the modified AFM probe could be measured.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.4
• /
• pp.575-581
• /
• 2013

In this paper, we experimentally investigated the effects of attached cylindrical tripwires on the aerodynamic performance. The research was carried out with a simple two-dimensional (2-D) rectangular airfoil fabricated from thin flat-plate aluminium, with elliptical leading and trailing edges. Tripwires of varying widths and thicknesses, and attack angles of $-5^{\circ}{\sim}20^{\circ}$ were used to investigate the aerodynamic characteristics (e.g. lift and drag forces) of the airfoil. We found that attaching the tripwires to the lower surface of the airfoil enhanced the lift force and increased the lift-to-drag ratio for low attack angles. However, attaching the tripwires to the upper surface tended to have the opposite effects. Moreover, we found that attaching the tripwires to the trailing edge had similar effects as a Gurney flap. The aerodynamic characteristics of the flat-plate airfoil with tripwires can be used to develop passive control devices for aircraft wings in order to increase their aerodynamic performance when gliding at low attack angles.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.10
• /
• pp.1314-1325
• /
• 1997

Experiments have been conducted to determine the flow and heat transfer characteristics for a two-dimensional turbulent wall attaching offset jet at different oblique angles to a flat surface. The distributions of the wall static pressure coefficient and time-averaged reattachment position for various offset ratios and oblique angles have been measured. The local Nusselt number distributions on the plate surface were also measured using liquid crystal as a temperature indicator. The new hue-capturing technique utilizing a true color image processing system was used to accurately determine the temperature of the liquid crystal. The experiments were carried out at Reynolds number, Re (based on D) of from 7300 to 21,300 with offset ratio, H/D from 2.5 to 10, and oblique angle, .alpha. from 0 deg. to 400 deg..

• Journal of the Korean Mathematical Society
• /
• v.28 no.2
• /
• pp.359-378
• /
• 1991