• Tribology and Lubricants
• /
• 제9권2호
• /
• pp.63-69
• /
• 1993

The wear properties of two types of $Si_3N_4$(silicon nitride) exposed to high and low humidity were examined experimentally for various sliding speed. Bearing steel was used as the disk material at pin-on-disk type sliding. Wear rates of pressureless sintered-plus-hot-isostatic pressed Si3N4 were slightly lower than those of pressureless sintered $Si_3N_4$. It was observed that adsorbed moisture and sliding speed markedly influenced the wear properties of $Si_3N_4$. The highest wear rate was obtained under the high humidity and low sliding speed condition. As the sliding speed was increased, wear rates were decreased and the humidity effect on the wear rates of $Si_3N_4$ was lowered. The result that the $Si_3N_4$ pin showed a high wear rate under the high humidity condition was explained by the property change due to the adsorbed moisture, plowing action by the hard particles of $Fe_2O_3$ from the disk, and the corrosion effect at $Si_3N_4$ surface. Increase in sliding speed was supposed to have reduced the humidity effect on wear rate of $Si_3N_4$ by raising the temperature of both the bearing steel disk and $Si_3N_4$ pin specimen.

• 한국산학기술학회논문지
• /
• 제21권5호
• /
• pp.648-655
• /
• 2020

현대의 자동소총의 공이는 공이치기에 의해 타격을 받아 장전된 탄약의 뇌관을 기폭 시키는 역할을 한다. 이 과정에서 공이는 충격하중을 받게 되며 소총의 수명주기 동안 반복적인 힘을 받게 된다. 소총의 내구도 시험에서 전체의 96.26% 진행 중 공이가 조기에 파손되는 현상이 발생하였다. 이에 따라 원인분석과 재현시험을 통해 파손현상 사례연구를 실시하였다. 파손이 발생한 공이의 파단면을 현미경 및 SEM 분석결과 반복충격에 의해 표면 원주방향 전체에서 균열이 시작해 심부로 피로균열이 발생했다. 반복충격에 의해 균열이 성장하다 마지막에 피로파괴가 발생하였으며, 노치에 의한 것으로 추정되었다. 검증을 위해 원주방향 0.03mm의 노치를 생성한 공이로 재현시험결과 동일한 형태의 파단면을 가지면서 전체 수명의 64.25%에서 파손되었다. 파손사례연구를 위한 노치형태별 재현시험결과 한쪽 측면 노치 0.3mm, 0.5mm의 공이는 각각 65.53%, 50.76%에서, 6개 지점의 노치 0.03mm는 85.65%에서 파손되었다. 마지막으로 표면 거칠기가 거칠고 툴 마크가 육안으로 확인이 가능한 공이는 내구수명을 만족하며 381㎛의 내부균열이 진행되었다. 본 연구를 통해 노치형태별 파손에 대해 고찰하였으며, 반복충격을 받는 부품의 신뢰성 확보를 위해 노치와 표면 거칠기 품질관리가 중요한 것을 알 수 있다.

• 센서학회지
• /
• 제3권3호
• /
• pp.16-21
• /
• 1994

표준 CMOS공정으로 제작되며 게이트 콘트롤을 가지는 3단자형의 pin type 수광센서를 제안하고 이를 CMOS회로와 집적하여 제작하였다. $100{\mu}m{\times}120{\mu}m$ 크기로 제작된 수광센서의 암전류(Dark current)는 -5V에서 1nA이하, 정전용랑은 0.75pF, 항복전압(Breakdown voltage)은 -l4V이상의 특성을 보였다. 응답도는 $0.805{\mu}m$의 파장에서 0.19A/W(양자효율 30%), $0.633{\mu}m$에서는 0.25A/W(양자효율 50%)였으며 게이트에 전압을 가하면 응답도가 증가하였다. 이 수광센서를 CMOS 디지탈 인버터와 집적했을때 $22k{\Omega}$의 전달이득(Transimpedance)을 가지며 $90{\mu}A$의 광전류로 별도의 증폭단없이 인버터를 스위칭시켰다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.389-392
• /
• 2004

It is clinically well known that pre-tension of wires increases the fracture stability in ring or hybrid external fixation. In some cases, additional half pin should be necessary to increase the stability when soft tissue impalement occurs during fixation. In this paper, the fracture stability of a hybrid external fixator system with different pre-tension effects and additional half-pins was analysed using FEM to investigate the effects of these pre-tension and half pin on the system stability quantitatively. 3-D finite element models of five different fixator frames were developed using by beam elements. In axial compression analysis, the fracture stiffness was increased maximally 62％ as the pre-tension increased. In torsion analysis, in the other hand, there is little variations in the fracture stiffness. Additional half pin increased the system stiffness about 200 ％. From the results, proper pre-tension and additional half pin would provide good methods to increase the fracture stability of the hybrid external fixator and provide more surgical options to minimize soft tissue damage at the fracture site.

• 전자공학회논문지A
• /
• 제29A권4호
• /
• pp.38-48
• /
• 1992

OEIC(Optoelectronic Integrated Circuit)'s can be integrated horizontally or vertically. Horizontal integration approach is, however, more immune to parasitic and more universally applicable. In this paper, a structural modeling, fabrication and characterization of PIN photodiodes which can be used in the horizontal integration are performed. For device modeling, we build a transmission line model from 2-D device simulation, from which lumped model parameters are extracted. The speed limits of the PIN photodiodes can also be calculated under various structural conditions from the model. Thus optimum design of horizontally integrated PIN photodiodes for high speed operation are possible. Such InGaAs/InP PIN photodiodes for long-wavelength communications are fabricated using pit etch, epi growth, planarization, diffusion and metallization processes. Planarization process using both RIE and wet etching and diffusion process using evaporated Zn$_{3}P_{2}$ film are developed. Characterization of the fabricated devices is performed through C-V and I-V measurements. At a reserve bias of 10V, the dark current is less than 5nA and capacitance is about 0.4pF. The calculated bandwidth using the measured series resistance and capacitance is about 4.23GHz.

• 한국전기전자재료학회논문지
• /
• 제37권4호
• /
• pp.412-419
• /
• 2024

Mn-doped Pb(In_1/2Nb_1/2)O₃-Pb(Mg_2/3Nb_1/3)O₃-PbTiO₃ (Mn:PIN-PMN-PT) single crystals, which exhibit improved phase transition temperatures and coercive field properties compared to Pb(In_1/2Nb_1/2)O₃-Pb(Mg_2/3Nb_1/3)O₃-PbTiO₃ (PIN-PMN-PT) single crystals, are expected to be utilized in high-power acoustic transducers. Bridgeman method, growing single crystals along the axial direction from melt, is most widely used method for single crystal growth with large size and high quality. However, single crystal boules grown by the Bridgeman method demonstrate a PT compositional variation, giving rise a distribution of crystal structure and material properties along the growing axis. To employ piezoelectric single crystals grown by the Bridgeman method for acoustic transducers, it is essential to investigate their overall property distribution. In this study, the compositional distribution and property variation of Mn:PIN-PMN-PT single crystals grown by the Bridgeman method was investigated. Measured compositional distribution of PT was from 29% to 32.5% in the Rhombohedral crystal region of the boule. Two types of specimen, [011]-poled Mn:PIN-PMN-29PT and Mn:PIN-PMN-32PT single crystals, were fabricated and tested to obtain full property variation at both ends of the Rhombohedral crystal region. The properties related to the 32 directional vibration mode and the properties related to high-power driving were measured to confirm the overall distribution of properties by composition.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1403-1415
• /
• 2021

The transient capability of a SP₃ based pin-wise core analysis code SPHINCS is developed and verified through the analyses of the C5G7-TD benchmark. Spatial discretization is done by the fine mesh finite difference method (FDM) within the framework of the coarse mesh finite difference (CMFD) formulation. Pin size fine meshes are used in the radial fine mesh kernels. The time derivatives of the odd moments in the time-dependent SP₃ equations are neglected. The pin homogenized group constants and Super Homogenization (SPH) factors generated from the 2D single assembly calculations at the unrodded and rodded conditions are used in the transient calculations via proper interpolation involving the approximate flux weighting method for the cases that involve control rod movement. The simplifications and approximations introduced in SPHINCS are assessed and verified by solving all the problems of C5G7-TD and then by comparing with the results of the direct whole core calculation code nTRACER. It is demonstrated that SPHINCS yields accurate solutions in the transient behaviors of core power and reactivity.

• 한국안전학회지
• /
• 제21권1호
• /
• pp.48-52
• /
• 2006

This study is a research of safety valve development for LP gas cylinder which use sintering metal. Re-searcher wishes to apply technology of sintering metal for safety valve development and do gas flow control. The basis of this study is most suitable fluid examination that to reduce gas accident. This research concluded following results. 1. When press pin length is 42mm to 45mm powder quantity is 0.25g, in case of press pin length 36mm to 42mm powder quantity is 0.2g, displayed fluid optimization. 2. When press pin length is 39mm and powder quantity is 0.25g, press pressure displayed fluid optimization at all interests from $1.2\;tons/cm^{2}\;to\;2\;tons/cm^{2}$. 3. When apparent density is about $5.0g/cm^{3}\;to\;4.5g/cm^{3}$, fluid optimization becomes.

• Journal of the Korean Wood Science and Technology
• /
• 제42권3호
• /
• pp.258-265
• /
• 2014

목구조물 접합부에 기존 드리프트핀(Drift pin)을 대체하고자 단판이나 합판을 유리섬유강화플라스틱(GFRP: Glass fiber reinforced plastic)과 복합 적층시킨 GFRP보강적층목재핀을 제작하였다. 더불어 GFRP보강적층목재핀을 사용하여 집성재 접합부의 인장형 전단내력 시험을 실시하였다. GFRP 배열에 따른 보강적층목재핀의 휨강도 시험결과 GFRP를 각층에 1장씩 삽입한 시험편(Type-A)이 가장 양호한 성능을 발휘하였다. 또한 압체압력 $1.96N/mm^2$, 온도 $150^{\circ}C$에서 한 시간 열압하여 고밀화한 시험편이 고밀화하지 않은 시험편과 비교하여 휨강도 성능이 1.57배 향상됨을 확인하였으며, 하중방향에 따라 Edgewise가 Flatwise보다 3.51배 높은 성능을 발휘하였다. 시험을 통해 가장 양호한 성능을 보인 Type-A 보강적층목재핀을 이용하여 전단내력 시험을 실시하였다. 접합구의 종류와 접합판의 종류를 달리하여 시험한 결과 드리프트핀과 강판을 적용한 시험체(Type-DS)와 비교하여 GFRP보강적층목재핀과 GFRP보강목재적층판을 적용한 시험체(Type-WL)가 1.12배 높은 전단내력이 측정되었으며 최대하중 이후에도 매우 양호한 인성이 관찰되었다.

• 한국임상수의학회지
• /
• 제41권3호
• /
• pp.189-194
• /
• 2024

Cinereous vulture (Aegypius monachus) is a large raptor that belongs to the family Accipitridae in the order Falconiformes. It is a migratory bird that returns to Mongolia after wintering in the Korean Peninsula. In February 2015, a cinereous vulture was rescued from Asan-si, Chungcheongnam-do Province as it could not fly. It was transferred to the Chungnam Wild Animal Rescue Center in Korea. It was found to have a closed fracture on the right radius through radiographic examination, a basic procedure. Surgery was performed at the fracture site using a shuttle pin and wire. After successful physical therapy and rehabilitation, the cinereous vulture was released in October 2015. A metal ring (150-00713) and wing tags (G/BL 3) were attached to the bird before its release for subsequent identification. Two years and 4 months later, in March 2018, the cinereous vulture was rescued and brought back to the center. It was diagnosed with secondary pesticide poisoning. After receiving treatment, a radiography test revealed no specific findings related to the previous fracture surgery. Considering that migratory birds travel long distances, it was confirmed that the treatment for reducing the fracture in the radius using a shuttle pin and a cerclage wire was suitable.