• Preventive Nutrition and Food Science
• /
• 제8권3호
• /
• pp.278-283
• /
• 2003

Textural properties of tofu manufactured with micronized full-fat soyflour (MFS) were enhanced by the addition of soy protein isolate, whey protein concentrate, chitosan oligosaccharide and mushroom powder. The MFS solution (14.2% solid content) was converted to semi-solid tofu by a two-stage heat treatment with the addition of 4% coagulant mix. The MFS tofu was evaluated by a compression test as well as sensory evaluation. To produce the semi-solid gel (MFS tofu) with reasonably high strength and toughness, the MFS solution with 14.2% solid content and 7.0% protein had to be heat treated at 121$^{\circ}C$ for 3min. The relative toughness of MFS tofu was increased by the addition of SPI, showing a 144% increase. The toughness of MFS tofu prepared with the MFS/SPI mixture was greatly increased by the addition of WPC at the level of 0.7% and the water separation from MFS tofu was greatly reduced. Furthermore, the toughness and strength of MFS/SPI tofu was enhanced by the addition of 0.1% chitosan oligosaccharide and 0.2% mushroom powder. The sensory evaluation of the tofu fortified with SPI, chitosan oligosaccharide and mushroom powder was superior to that of MFS tofu, with a higher score for overall preference.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1437-1439
• /
• 1996

In this paper, investigations on a three stage processing technique involving the co-evaporation of In-Se, Cu-Se and In-Se in this order at different deposition condition was undertaken. At first stage, we obtained good $In_{2}Se_{3}$ films by In-Se coevaporation. $In_{2}Se_{3}$ films show smooth and dense structure. And ration of In:Se was 2:3 $CulnSe_2$ thin films deposited by three stage process have shown strong adhesion on Mo coated glass substrates and good morphological properties suitable device fabrication. XWD spectra show single phase chalcopyrite $CulnSe_2$ films with strong orientation in the 112 plane. Resistivity of $CulnSe_2$ thin films was about $5{\times}10^{5}\;{\Omega}{\cdot}cm$. Surface morphology of CdS/$CulnSe_2$/Mo films was very good because of no pin holes.

• Preventive Nutrition and Food Science
• /
• 제9권3호
• /
• pp.206-212
• /
• 2004

Prickly pear extract (PPE) was fermented by Lactobacillus rhamnosus LS at 3$0^{\circ}C$ for 2 days. To improve the physicochemical properties of fermented PPE, it was fortified with food polysaccharides (0.2 %) or seaweed calcium before lactic acid fermentation. The viable cell counts, flow behavior, titratable acidity and color stability of fermented PPE were evaluated during 4 weeks of cold storage. Addition of xanthan gum or glucomannan increased the apparent viscosity and acid production, viable cell counts and red color of PPE were also well maintained during the cold storage. However, fermenting PPE with gellan gum resulted in a decrease in relative absorbance, indicating lower color stability. In particular, PPE fortified with carrageenan or alginic acid showed reduced acid production and lower viable cell counts. Addition of seaweed calcium at a 0.1 % level had positive effects on color stability, and helped maintain viable cell counts of 4.1 ${\times}$ 10$^{9}$ CFU/mL. This study demonstrated that xanthan gum could be used as a good thickening agent and stabilizer for retaining viable cell counts and red color during the cold storage in PPE fermented by lactic acid bacteria.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제12권1호
• /
• pp.171-179
• /
• 1990

This is a report on a case of delayed reconstruction after partial mandibularectomy for Ameloblastoma involving symphysis and bodies of the mandible by using of two large pieces of corticocancellous bone blocks obtained from both iliac crests. The authors failed immediate reconstruction with two kinds of Alloplasts(metal, methylmethacrylate) at two times of trial due to known infection and suggestive poor histocompatibility of materials aginst the host who has been suffered from long-term and active pulmonary tuberculosis. However we could get success late reconstruction of this problem-occured and curved area with two pieces of large corticocancellous blocks by using of miniplate osteosynthesis and biphasic external pin fixation. From our experience we are obtained some results as follows : 1. Alloplastic graft materials seemed to be dangerous to maintain successfuly in patient who has a long-term debilitating disease as a active pulmonary tuberculosis. 2. Biphasic external skeletal pin fixation appliance gave many advantages such as maintain functional position of the remained bodies and condyles of the mandible after removal of failed alloplasts and during control of inflammation of this area, assist supportive roles to fix and maintain bone grafts during healing, allow mandibular movement during healing and so offer to conduct normal functional stimuli to bone grafts during osteogenesis etc. 3. Bony union was successful between not only normal bones and grafted bones but also grafted bone pieces even though we used two pieces of large blocks of corticocancellous bone for graft. 4. Miniplate osteosynthesis was not affect any adverse effects to bone grafts but offered good role of fixation and maintenance for bone grafts.

• 소성∙가공
• /
• 제23권6호
• /
• pp.345-350
• /
• 2014

The current study elucidates the effects of cementite spheroidization and pro-eutectoid ferrite on the sliding wear resistance in medium carbon (0.45wt%C) and high carbon (1wt%C) steels. Both steels were initially heat treated to obtain a fully pearlite or ferrite + pearlite microstructure. Spheroidizing heat treatments were performed on both steels to spheroidize the pearlitic cementite. Sliding wear tests were conducted using a pin-on-disk wear tester with the steel specimens as the disk and an alumina ($Al_2O_3$) ball as the pin. The sliding wear tests were carried out at room temperature in air with humidity of $40{\pm}2%$. Adapted sliding distance and applied load was 300m and 100N, respectively. Sliding speed was 0.1m/s and the wear-track radius was 9 mm. Worn surfaces and cross-sections of the wear track were examined using an SEM. Micro Vickers hardness of the wear-track subsurface was measured as a function of depth from the worn surface. Hardness and sliding-wear resistance of both steel decreased with increased spheroidization of the cementite. The decrease was more significant in the fully pearlitic steel (1wt%C steel). The steel with the pro-eutectoid ferrite showed relatively higher wear resistance compared to the spheroidized pearlitic steel.

• Journal of Yeungnam Medical Science
• /
• 제3권1호
• /
• pp.209-213
• /
• 1986

소아만성B형간염 환아 24명에게 항virus제인 ribavirin을 15mg/kg/day로 14일간 경구투여한 군과 투여하지 않은 대조군으로 나누어 12개월간 혈청 HBsAg과 HBeAg을 추적 검사한 결과 두군 모두에서 HBsAg과 HBeAg의 감소를 볼 수 없었으므로 ribavirin의 소아만성B형간염에 대한 치료효과는 없는것으로 보여진다. 또한 ribavirin 치료에 따른 특별한 부작용도 볼 수 없었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.114.2-114.2
• /
• 2017

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_S$). Resistance of indium zinc oxide (IZO) is similar to ITO and it can be used to flexible applications due to its amorphous structure. To solve these problems, our study introduced hybrid layers of IZO/Ag/IZO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thickness of the metal interlayer. It was found that the sheet resistance of the multilayer was mainly dependent on the thickness of the Ag layers. The $R_S$ of IZO(40)/Ag/IZO(40nm) multilayer was 5.33, 3.29, $2.15{\Omega}/{\Box}$ for Ag thickness of 10, 15, and 20nm, respectively, while the $R_S$ of an IZO monolayer(95nm) was $59.58{\Omega}/{\Box}$. The optical transmittance at 550nm for the IZO(95nm) monolayer is 81.6%, and for the IZO(40)/Ag/IZO(40nm) multilayers with Ag thickness 10, 15 and 20nm, is for 72.8, 78.6, and 63.9%, respectively. The defrost test showed that the film with the lowest RS had the highest heat generation rate (HGR) for the same applied voltage. The results indicated that IZO(40)/Ag(15)/IZO(40nm) multilayer has the best suitable property, which is a promising thin film heater for the application in vehicle windshield.

• 한국추진공학회지
• /
• 제2권3호
• /
• pp.1-9
• /
• 1998

풍력에너지는 자연의 에너지를 이용하므로써 환경문제와 경제적 측면에서 다른 대체 에너지보다 훨씬 유리하여 세계 여러 나라에서 각광을 받고 있다. 경제적인 이유로 풍력발전을 위한 회전날개가 대형화 되고 있으며, 경량화를 위해 복합재 구조등의 첨단 항공기술이 적용되고 있는 추세이다. 본 연구에서는 500㎾급 중형 풍력 발전시스템을 개발함에 있어, 적합한 공력 성능을 갖는 경량화 복합재 회전날개의 개선 설계를 수행하였다. 회전날개의 경량화를 위해 기 설계된 쉘-스파 구조물을 쉘-스파-샌드위치 구조물로 설계를 수정하였고, 배선형 해석을 통해서 경량화에 따른 대변형 문제를 검토하였으며, 파괴응력보다 낮은 상태에서 발생되는 국부좌굴에 의한 구조물의 안전성을 검토하였다. 또한, 허브의 금속재 삽입부분의 전단핀에 의한 핀 홀 주위의 응력해석을 수행하여 충분히 안전함을 확인하였고, 수정 설계된 구조물이 운용구간내에서 공진이 발생하지 않음을 확인하였다.

• Nuclear Engineering and Technology
• /
• 제48권6호
• /
• pp.1291-1302
• /
• 2016

This paper presents a new and efficient scheme to determine the optimal neutron source position in a model near-equilibrium pressurized water reactor, which is based on the OPR1000 Hanul Unit 3 Cycle 7 configuration. The proposed scheme particularly assigns importance of source positions according to the local adjoint flux distribution. In this research, detailed pin-by-pin reactor adjoint fluxes are determined by using the Monte Carlo KENO-VI code from solutions of the reactor homogeneous critical adjoint transport equations. The adjoint fluxes at each allowable source position are subsequently ranked to yield four candidate positions with the four highest adjoint fluxes. The study next simulates ex-core detector responses using the Monte Carlo MAVRIC code by assuming a neutron source is installed in one of the four candidate positions. The calculation is repeated for all positions. These detector responses are later converted into an inverse count rate ratio curve for each candidate source position. The study confirms that the optimal source position is the one with very high adjoint fluxes and detector responses, which is interestingly the original source position in the OPR1000 core, as it yields an inverse count rate ratio curve closest to the traditional 1/M line. The current work also clearly demonstrates that the proposed adjoint flux-based approach can be used to efficiently determine the optimal geometry for a neutron source and a detector in a modern pressurized water reactor core.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.1-8
• /
• 2019

Demand for plastic gears are increasing in many industries due to their low production cost, light weight, applicability without lubricant, corrosion resistance and high resilience. Despite these benefits, utilizing plastic gears is limited due to their poor material properties. In this work, DLC coating was applied to improve the tribological properties of polyamide66 gear. 0 V, 40 V, and 70 V of negative bias voltages were selected as a deposition parameter in DC magnetron sputtering system. Pin-on-disk experiment was performed in order to investigate the wear characteristics of the gears. The results of the pin-on-disk experiment showed that DLC coated polyamide66 with 40 V of negative bias voltage had the lowest friction coefficient value (0.134) and DLC coated PA66 with 0 V of negative bias voltage showed the best wear resistance ($9.83{\times}10^{-10}mm^3/N{\cdot}mm$) among all the specimens. Based on these results, durability tests were conducted for DLC coated polyamide66 gears with 0 V of negative bias voltage. The tests showed that the temperature of the uncoated polyamide66 gear increased to about $37^{\circ}C$ while the DLC coated gear saturated at about $25^{\circ}C$. Also, the power transmission efficiency of the DLC coated gear increased by about 6% compared to those without coating. Weight loss of the polyamide66 gears were reduced by about 73%.