• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.911-916
• /
• 2001

Structural acoustic modification method based on the structural mobility analysis is applied to reduce the structure-borne noise radiated from hard disk drive system. Sound intensity techniques and ODS(Operational Deflection Shape) techniques are also used in order to provide the structural acoustic information for the mobility modification. The sound intensity is for the acoustic visualization of the noise source locations, and the ODS is for the visualization of the vibration pattern and its dynamic characteristics of the noise sources. Using visualization information of sound and vibration, local structural input mobility is reduced in the frequency band of interest by designing asymmetrical wave-stringer structure in the wave-number domain as well as frequency domain. The overall sound pressure level is reduced by 4dB and its controlled sound power radiated from the disk drive is proved to under 2.8Bel in idle-spinning mode and 3.1 Bel in random-seeking mode, which are the lowest noise levels in the hard disk drive industry.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1706-1715
• /
• 2016

In this paper, a single phase modified switched-diode topology for both symmetrical and asymmetrical cascaded multilevel inverters is presented. It consists of a Modified Switched-Diode Unit (MSDU) and a Twin Source Two Switch Unit (TSTSU) to produce distinct positive voltage levels according to the operating modes. An additional H-bridge synthesizes a voltage waveform, where the voltage levels of either polarity have less Total Harmonic Distortion (THD). Higher-level inverters can be built by cascading MSDUs. A comparative analysis is done with other topologies. The proposed topology results in reductions in the number of power switches, losses, installation area, voltage stress and converter cost. The Nearest Level Control (NLC) technique is employed to generate the gating signals for the power switches. To verify the performance of the proposed structure, simulation results are carried out by a PSIM under both steady state and dynamic conditions. Experimental results are presented to validate the simulation results.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.542-550
• /
• 2011

This paper describes the design and hardware implementation of a Single Input Fuzzy Logic Controller (SIFLC) to regulate the output voltage of a boost power converter. The proposed controller is derived from the signed distance method, which reduces a multi-input conventional Fuzzy Logic Controller (CFLC) to a single input FLC. This allows the rule table to be approximated to a one-dimensional piecewise linear control surface. A MATLAB simulation demonstrated that the performance of a boost converter is identical when subjected to the SIFLC or a CFLC. However, the SIFLC requires nearly an order of magnitude less time to execute its algorithm. Therefore the former can replace the latter with no significant degradation in performance. To validate the feasibility of the SIFLC, a 50W boost converter prototype is built. The SIFLC algorithm is implemented using an Altera FPGA. It was found that the SIFLC with asymmetrical membership functions exhibits an excellent response to load and input reference changes.

• Journal of Power Electronics
• /
• 제13권1호
• /
• pp.20-30
• /
• 2013

This paper presents a soft switching DC/DC converter for high voltage application. The interleaved pulse-width modulation (PWM) scheme is used to reduce the ripple current at the output capacitor and the size of output inductors. Two converter cells are connected in series at the high voltage side to reduce the voltage stresses of the active switches. Thus, the voltage stress of each switch is clamped at one half of the input voltage. On the other hand, the output sides of two converter cells are connected in parallel to achieve the load current sharing and reduce the current stress of output inductors. In each converter cell, a half-bridge converter with the asymmetrical PWM scheme is adopted to control power switches and to regulate the output voltage at a desired voltage level. Based on the resonant behavior by the output capacitance of power switches and the transformer leakage inductance, active switches can be turned on at zero voltage switching (ZVS) during the transition interval. Thus, the switching losses of power MOSFETs are reduced. The current doubler rectifier is used at the secondary side to partially cancel ripple current. Therefore, the root-mean-square (rms) current at output capacitor is reduced. The proposed converter can be applied for high input voltage applications such as a three-phase 380V utility system. Finally, experiments based on a laboratory prototype with 960W (24V/40A) rated power are provided to demonstrate the performance of proposed converter.

• 수완나부미
• /
• 제6권1호
• /
• pp.161-191
• /
• 2014

The entry of the logging industry in the once heavily forested riverine middle Agusan Valley where aboriginal Manobos live meant the entry of the material practice of wage labor into this out-of-the-way place. Wage labor converted the once relatively isolated, subsistence animist Manobos into laborers of the expanding capitalist regime. A symptom of modernity, this wage labor also accompanied the coming of Visayan settlers (also loggers paid by wage) who introduced indigenous Manobos the compadrazgo social relationship. This friendly relationship across ethnic identities legitimated social ties and is a social material practice represented in recent bilingual Manobo possession rituals where the Visayan spirit is incarnated along with Manobo spirits. To understand the idea behind spirit embodiment, I explore Manobo ritual as mimesis or poeisis. This representation is shaped by concrete material realities as much as these realities, in turn, are reconfigured by ritual practice. In the older Manobo cosmology, which is based on subsistence economy and dependent on the forest and rivers, individuals have an externalized self (as manifest in the idea of twin soul), in which the inner vital principle is co-extensive with a spirit double in cosmos. Manobos imitate the perceived workings of nature in ritual so as to control them in times of illnesses. In contrast, the mimesis of the Visayan spirit is based on a different political economic set up with its attendant asymmetrical interpersonal relationship. By symbolically representing the Visayan patron as friend, Manobos are able to negotiate the predicament of their subalternity in local modernity.

• The Journal of Korean Physical Therapy
• /
• 제9권1호
• /
• pp.127-145
• /
• 1997

The purpose of this study wa9 to analyse the gait patterns of two female children with hemiplegic cerebral palsy by using the three-dimensional video motion analysis technique. Case 1 has mild spastic hemiplegia on the right side while Case 3 has moderate spastic hemiplegia on the left side. A group of 10, normal female children of the same age(7-8 years old) were selected as the control group for comparison. Time and distance variables as well as the Center of Mass displacement, and the pelvic and joint motions in three anatomical planes were analysed for this purpose. The following observations were made through the analysis : Case 1 revealed an asymmetrical gait pattern in which the step length of the unaffected side was shorter than that of the affected side, which wan a result of the effort to minimize loading on the affected leg by shortening the swing phase of the unaffected leg. Case 1 scored similar phase ratios, cadence and walking velocity to the normal group. A slight posterior tilt of the pelvis was observed throughout the gait cycle. Less hip and knee flexion than the normal group was observed, and demonstrated hyperextension of the knee in the terminal stance phase. The main problem in case 1 originated from the insufficient dorsiflexion of the affected foot during the swing phase. Therefore, Case 1 has difficulty with foot clearance in the swing phase. Usually, this is compensated for by using exessive hip abduction and medial rotation in conjuction with trunk elevation as well as increased vortical displacement of the center of mass. Case 1 revealed a foot-flat initial contact pattern. Case 2 was characterized by a consistent retraction ef the affected aide of the body througout the gait cycle, As a result, an asymmetrical gait pattern with increased stance phase ratios of the unaffected side was observed. In spite of this the step lengths of both sieds were similar. Case 2 scored lower cadence and walking speed than the normal group with lower gait stability. The main problem in Case 2 originated from an excessive plantaflexion of the affected foot which, in turn, rebutted in high hip and knee flexion. Hyperextension of the knee was observed at mid-stance, and execessive anterior tilt of the pelvis throughout the gait cycle was noticed. A gait pattern with high hip abduction and medial circumduction was maintained for the stability in the stance phase and foot clearance in the swing phase. Case 2 revealed a forefoot-contact initial contact pattern.

• 한국해양학회지
• /
• 제29권3호
• /
• pp.217-227
• /
• 1994

한반도 서부대륙붕은 북동.남서방향의 불연속적인 사퇴가 잘 발달되어 있다. 사 퇴의 규모는 높이 3~21 m, 파장 3.1~6.8 km, 길이 9~64 km이며 경사도는 0.5이다. 이러한 사퇴들은 해수면상승에 따른 수심변화와 조류의 세기변화로 인하여 형성되고 변형 되어지는 것으로 해석된다. 사퇴의 특징은 다음과 같다. (1)사퇴의 발달이 조류 방향과 대체로 일치하는 북동-남서방향으로 발달하고 있다. (2) 사퇴의 내부는 3.5kHz 탄성파단면도와 주상퇴적물에 의해 두 개의 층(sequence)으로 구분된다. 상부층은 내 부 반사면이 없는 확산(prolonged type)된 음향상이 나타나며, 균질(massive)의 세립 사(Mx, 2-3$\psi$)로 구성되어 있다. 그 하부층은 수평내부반사(parallel internal reflector) 음향상이 나타나며, 엽리구조(kaminated structure)가 발달한 사질니 또는 니질사(Mz, 5-7$\psi$)로 구성되어 있다. 수평한 내부반사면은 사퇴의 양쪽 경사면에서 절 단(truncation)된 모습을 보이고 있다. (3) 비대칭형(asymmetrical type)의 모래파가 사퇴를 덮고 있다. 모래파의 급경사면이 사퇴의 서측은 동북동, 동측은 서남서방향을 향하고 있다. 반면, 사퇴의 정부는 대칭형(symmetrical type)의 모래파가 분포한다. 이러한 특징을 가진 사퇴의 기원은 하부퇴적층이 강한 조류에 의해 침식(scouring)되 어 등성이와 같은 지형을 형성하고, 침식되고 남은 조립질의 잔류퇴적물이 등성이의 상부를 피복하여 형성된 것으로 해석된다.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1152-1162
• /
• 2011

In this paper, a single-phase DC-AC inverter using two embedded Z-source converters is proposed. The proposed inverter is composed of two embedded Z-source converters with common DC source and output AC load. The output AC voltage of the inverter is obtained by the difference of output capacitor voltages of each converter. The output voltage of each converter take shape of the asymmetrical AC waveform centering zero voltage. Therefore, the proposed inverter can generate the same output voltage despite low VA rating L-C elements, compared to the conventional inverter using high DC voltage with AC ripple. To verify the validity of the proposed system, the PSIM simulation was achieved under the condition of rapid increase of DC source (110[V]${\rightarrow}$150[V]) and R-load (50[${\Omega}$]${\rightarrow}$300[${\Omega}$]). For controlling the voltage of the inverter system, the one-cycle controller was adopted. As results, the proposed inverter output the constant AC voltage (220[V]rms/60[Hz]) for all conditions. Also, the R-L load and nonlinear diode load were adopted for the proposed inverter loads, and we could know that the its output voltage characteristics were as good as the pure R-load. Finally, the RMS and THD of output AC voltage were examined for the different loads, input DC voltages and reference voltage signals.

• 한국산학기술학회논문지
• /
• 제17권11호
• /
• pp.363-367
• /
• 2016

본 연구는 마하수 2.5의 초음속 영역에서 마하수 1.0의 슬롯 분사가 있는 후향계단 형상에 대한 유동장 특성을 분석하기 위하여 초음속풍동 시험부를 설계, 제작하였다. 비행체가 고속으로 움직일 때 공동 주위의 유동은 매우 복잡하여 수치해석 결과를 검증할 초음속풍동 시험 자료가 필요하기 때문에 기존의 2차원 대칭형 노즐을 아랫면이 평판인 비대칭형 노즐로 수정하였다. 특성곡선해법을 이용한 비점성 노즐을 설계하고, 시험을 통해 얻은 경계층 두께를 노즐에 반영하여 보정한 기법을 C 언어로 프로그래밍하여 얻은 결과를 수치해석 결과와 비교하여 검증하였다. 슬롯 분사 시 지속적인 유동장 변화 분석을 위한 초음속 유지시간 확보를 위해 저장탱크의 압력 변화에 따른 PID 제어프로그램 수정으로 초음속 유동 유지시간을 약 5초에서 약 6초로 1초 정도 연장하여 제어 효율을 향상하였고, 슬롯 분사가 있는 후향계단에서의 유동장 변화를 슐리렌장치로 가시화하여 복잡한 유동장 특성을 확인하였다. 향후 슬롯 분사의 속도와 유량, 유동장의 온도를 변화하여 공동에서의 막냉각 효과 분석을 위한 장비로 사용할 계획이다.

• 대한인간공학회지
• /
• 제33권2호
• /
• pp.109-124
• /
• 2014

Objective: This study was conducted for one-hand users including hemiplegic clients currently using general folding manual wheelchairs, so as to analyze their specific problems and recommend solutions regarding usage. Background: Traditional manual wheelchairs require considerable use and control of both hands for operation, thus adaptations become necessary for individuals with asymmetrical use of hands. Method: Thirty hemiplegic clients who were admitted to rehabilitation and convalescent hospitals participated as subjects. The research tools were general folding manual wheelchairs commonly used by people with impaired gait, and the Wheelchair Skills Tests (WST) WST-M/WCU 4.1 version was adopted as the assessment tool. All participants were asked to fill out questionnaires on demographics and wheelchair usage characteristics. Assessment procedures were performed with currently used manual wheelchairs and with/without the use of foot to control the wheelchair. Results: When the participants drove folding manual wheelchairs without the use of foot, even the lowest failure rate among the WST items tested recorded 96.7%. On the contrary, with the use of foot in maneuvering the wheelchairs, failure rates dropped noticeably and success rate among the WST items tested was as high as 86.7%. Conclusion: These findings imply that the use of one-arm (hand) propellable (drivable) wheelchair can be an active and effective solution in resolving problems for hemiplegic clients using existing manual wheelchairs. As such, the government should provide institutional support to further develop and distribute this device or technology, and promote relative research in tandem. For now, the supply of commercially available device to hemiplegic clients is deemed urgent and also a mechanism to provide the devices and relevant services. Application: This study offers viable solutions for hemiplegic clients who rely on existing manual wheelchairs to increase their mobility and occupational performance.