• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.33-38
• /
• 2008

Numerical investigation of asymmetric vortices at high angles of attack subsonic flow is performed using three-dimensional Navier-Stokes equations. A small bump has been carefully selected and attached near the nose of an ogive cylinder to simulate symmetric vortices. Selected bump shape does develop asymmetric vortices and is verified using Lamont's experimental results. By changing the angle of attack, Reynolds numbers, and Mach numbers, the characteristics of asymmetric vortices are observed. The angle of attack which contributes significantly to the generation of asymmetric vortices are over 30 degrees. By increasing Mach number and Reynolds number asymmetric vortices, hence the side forces show decreasing trend..

• Journal of computational fluids engineering
• /
• v.13 no.2
• /
• pp.8-13
• /
• 2008

A supersonic viscous flow over a five-degree half-angle cone is studied computationally with three-dimensional Navier-Stokes equations. Steady asymmetric solutions show that the asymmetric flow separation is caused by convective instability. The effects of angle of attacks, Reynolds numbers, and Mach numbers have been investigated and it is found that those factors affect the generation of the side force. The side force has the maximum value at ${\alpha}=22^{\circ}$, while over ${\alpha}=22^{\circ}$, asymmetric vortex becomes transient, which results in the unsteady shedding. At the angle of attack of 22 degrees, the side force increases with Reynolds number and decreases with Mach number. The increase of the side force stops over the critical Reynolds number for the present configuration.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.171-176
• /
• 2007

Supersonic viscous flow over a 5 degree half angle cone studied computationally with three-dimensional Navier-Stokes equations. Steady asymmetric solutions of 5-deg half angle cone show that the asymmetric flow separation is caused by convective instability. The angle of attack, Reynolds number, and Mach number affected the side force variation that is caused by asymmetric vortical flow.

• Journal of Biosystems Engineering
• /
• v.42 no.3
• /
• pp.127-135
• /
• 2017

Purpose: Purpose: The usability of a mathematical model modified for analysis of the static stability of an asymmetric tractor-harvester system was investigated. Method: The modified asynchronous mathematical model was validated through empirical experiments, and the effects of movements of the center of gravity (CG) coordinates on the stability against lateral overturning were analyzed through simulations. Results: Changes in the lateral overturning angle of the system were investigated when the coordinates of the CG of the system were moved within the variable range. The errors between simulation results and empirical experiments were compared, and the results were -4.7% at the left side overturning and -0.1% at the right side overturning. The asymmetric system was characterized in such a way that the right side overturning had an increase in overturning angle in the (+) variable range, while it had a decrease in overturning angle in the (-) variable range. In addition, the left side overturning showed an opposite result to that of the right side. At the declination angle (296<${\gamma}$<76), the right side overturning had an increase in the maximum overturning angle of 3.6%, in the minimum overturning angle of 20.3%, and in the mean overturning angle of 15.9%. Furthermore, at the declination angle (284<${\gamma}$<64), the left side overturning had a decrease in the maximum overturning angle of 29.2%, in the minimum overturning angle of 44%, and in a mean overturning angle of 39.7%. Conclusion: The modified mathematical model was useful for predicting the overturning angle of the asymmetric tractor-harvester system, and verified that a movement of the CG coordinates had a critical effect on its stability. In particular, the left side overturning was the most vulnerable to stability, regardless of the direction of declination angle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.335-338
• /
• 2007

In the case of an antiaircraft missile, high angle of attack flight capability is required to get the agile maneuverability in a supersonic flow. Even through a symmetric slender body does not have side slip, asymmetric vortex is generated at high angle of attack conditions. This asymmetric vortex produces unnecessary side force and yawing moment; hence, these effects deteriorate directional stability. In this study, the numerical analysis of asymmetric vortices around the slender body was conducted at high angle of attack supersonic flow. In order to simulate the vortices, a bump is installed on the nose of the slender body. As a result of the numerical analysis, the asymmetric vortices around the slender body could be simulated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.4
• /
• pp.271-275
• /
• 2015

The floodlighting assists the pilot in taxiing the aircraft into and out of the final parking position and provide lighting suitable for passenger to embark and debark and for personnel to load and unload cargo. It is composed of sodium lamps which is consuming high energy. It needs to develop a dedicated LED lamp to replace the existing lamps. In this paper, We propose a suitable asymmetric angle of LED lamps to avoid a pilot's glare and to meet the standard illumination. For this, we analyze asymmetric angle of sodium lamps which are using in airport and confirm whether the illumination distribution and glare index meet the relating standards by using simulation method. Also, we study the needs of asymmetric characteristics of LED ramp by simulating the LED lamps with and without asymmetric characteristics of ramp respectively. With the simulation result, finally we propose the best asymmetric angle of LED lamp to meet the average illumination standard, and avoid a pilot's glare.

• Journal of Biosystems Engineering
• /
• v.30 no.6 s.113
• /
• pp.347-353
• /
• 2005

Paper angle, environment friendly packaging material, has been mainly used as an edge protector, But, in the future, paper angle will be applied to package design of heavy product such as strength reinforcement or unit load system (ULS). Therefore. understanding of buckling behavior fur angle itself, compression strength and quality standard are required. The objectives of this study were to characterize the buckling behavior by theoretical and finite element analysis, and to develop compression strength model by compression test for symetric and asymetric paper angle. Based on the result of theoretical and finite element analysis, as applied load level was bigger and/or the length of angle was longer, incresing rate of buckling of asymmetric paper angle was higher than that of symmetric paper angle. Decreasing rate of minimum principal moment of inertia significantly increased as the extent of asymmetric angle increased, and buckling orientation of angle was open- direction near the small web. Incresing rate of maximum compression strength (MCS) for thickness of angle decreased as the web size increased in symmetric angle. MCS of asymmetric angle of 43${\times}$57 and 33${\times}$67 decreased $15{\~}18\%$ and $65{\~}78\%$, and change of buckling increased $12{\~}13\%$ and $62{\~}66\%$, respectively.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.11 no.1
• /
• pp.1-10
• /
• 2005

Paper angle, environment friendly packaging material, has been mainly used as an edge protector. But, we have perceived its application to package design of heavy product such as strength reinforcement or unit load system (ULS) in the future. Above all, understanding of buckling behavior for angle itself and compression strength and quality standard have to be accomplished for the paper angle to be used for this purpose. The purpose of this study was to elucidate the buckling behavior through theoretical and finite element analysis, and to develop compression strength model by compression test for symetric and asymetric paper angle. Based on the result of theoretical and finite element analysis, increasing rate of buckling of asymmetric paper angle was higher as applied load level was bigger and/or the length of angle was longer than that of symmetric paper angle. Decreasing rate of minimum principal moment of inertia was remarkably increased as the extent of asymmetric angle is bigger, and buckling orientation of angle was open direction near the small web. Increasing rate of maximum compression strength (MCS) for thickness of angle was smaller as the web size was bigger in symmetric angle. MCS of asymmetric angle of $43{\times}57$ and $33{\times}67$ was decreased $15{\sim}18%$ and $65{\sim}78%$, and change of buckling was increased $12{\sim}13%$ and $62{\sim}66%$, respectively.

• Journal of the Korean Society of Safety
• /
• v.16 no.2
• /
• pp.117-120
• /
• 2001

Low back pain has been known as the most frequent musuculoskeletal disorders in modern industrial society and cost by low back pain is increasing mon and more. The asymmetric lifting has been identified as a major risk factor of low back pain. In this study, the muscle activity and muscle exertion level during asymmetric load handling (without trunk flexion) was estimated. The results of normalized MVC measurement were decreased about 16％, 24％, 34％ respectively as the asymmetric angle was $30^{\circ}$, $60^{\circ}$, $90^{\circ}$. From the results of EMG measurement contralateral muscles were more active than ipsilateral muscles. RMSEMG values of right erector spinae muscles were decreased as the work posture went to 90$^{\circ}$ and those of left erector spinae muscles were increased until the asymmetric angle was 40$^{\circ}$ but decreased continually over 40$^{\circ}$. And for seven of subjects, activities of left and right latissimus dorsi muscles were maintained constantly, while for remainer, those were irregular.

• Structural Engineering and Mechanics
• /
• v.15 no.4
• /
• pp.463-476
• /
• 2003

This paper deals with nonlinear asymmetric dynamic buckling of clamped laminated angle-ply composite spherical shells under suddenly applied pressure loads. The formulation is based on first-order shear deformation theory and Lagrange's equation of motion. The nonlinearity due to finite deformation of the shell considering von Karman's assumptions is included in the formulation. The buckling loads are obtained through dynamic response history using Newmark's numerical integration scheme coupled with a Newton-Raphson iteration technique. An axisymmetric curved shell element is used to investigate the dynamic characteristics of the spherical caps. The pressure value beyond which the maximum average displacement response shows significant growth rate in the time history of the shell structure is considered as critical dynamic load. Detailed numerical results are presented to highlight the influence of ply-angle, shell geometric parameter and asymmetric mode on the critical load of spherical caps.