• Journal of Ship and Ocean Technology
• /
• v.6 no.3
• /
• pp.37-45
• /
• 2002

A series of detailed study was performed to identify the sources of the propeller blade failure and resolve the problem systematically, by use of the theoretical tools and by the direct measurement and observation in the full-scale sea trials. The selection of inexperienced propulsion control system with a reversible gear system is shown to cause the serious damage to the propeller blades in crash astern maneuver, when the rotational direction of the propeller is changed rapidly. Quasi-steady analysis for propeller blade strength using FEM code in bollard backing condition indicates that the safety factor should be order of 18∼20 to avoid the structural failure for the selected propeller geometry and reduction gear system.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.4
• /
• pp.411-416
• /
• 2008

A strength problem of propeller blades for large container ships at astern condition has been occasionally reported due to the application of a highly skewed propeller which can reduce the hull surface fluctuation forces. A finite element analysis code for propeller blade was developed and utilized since 1985. Recently, however, further fine mesh modeling for finite element analysis is required to yield higher accuracy in the analysis. The present study shows an application of FE analysis code to the highly skewed propeller for large container ships. Results of FE analysis show that the number of FE mesh affects largely on strength, and also the calculated strength with fine mesh gives good agreements to those of other FEM codes. A method to enlarge strength near the trailing edge was introduced considering the strength criterion on the blade.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.10a
• /
• pp.160-161
• /
• 2012

The traditional theory regarding the pivot point of a ship during maneuvering, so called apparent pivot point, is located nearly at 1/3 ship's length from the bow when the ship is moving ahead, and between 1/4 ship's length from the stern and the rudder post when going astern. The pivot point is sometimes considered to be the centre of leverage for forces acting on the ship. However, the pivot point is located out of ship due to strong lateral force, such as current and it is very inconvenient to use during maneuvering a ship. In this paper firstly, pivot points due to ship's condition are investigated carefully. And then the center of lateral resistance used at the present are determined. While a new lateral force is added, we can compare the pivot point with the center of lateral forces. Finally, we will suggest the center of all lateral forces for maneuvering instead of pivot point. Especially, it will be very helpful for pilots to handle ships in simulation.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.3
• /
• pp.158-166
• /
• 2021

In this paper, a numerical analysis technique using a body force model is investigated to estimate the available net thrust of multi-pod-driven ice-breaking vessels under bollard pull and overload conditions. To employ the body force model in present flow simulations, drag and thrust components acting on the pod unit are calculated by using Propeller Open Water (POW) test data. The available net thrusts according to the direction of operation are evaluated in both bollard pull and overload conditions under deep water. The simulation results are compared with the model test data. The available net thrusts, calculated by the present analysis for ahead operating modes at 3~6 knots which are typical speeds of the target vessel in arctic field, are agreed well with the model test results. It is also found that the present result for astern operating mode appears approximately 6 % larger than the model test result. In addition, the available net thrusts are calculated under the both operating conditions accompanied by shallow water effects, and the main cause of the difference is studied. Based on the result of the present study, it is confirmed that the body force model can be applied to the performance evaluation of multi-pod propulsion system and the main engine selection in early design stage of the vessel.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.373-380
• /
• 2017

Operational errors caused by human factors, which is the major cause of marine accidents, include lack of knowledge, misunderstanding knowledge, and inadequate procedures. Recently, the type of propulsion mounted on KCG cutters has been diversified. In particular, the water jet propulsion unit, which was mainly installed in small boats, have been gradually expanded to medium and large size Coast Guard cutters, reaching 50% of the total. Axes types are divided into 2 to 4, and the bucket types are divided into Double Reverse Bucket(DRB) and Single Reverse Bucket(SRB); in these, the backward and steering control methods are completely different. Diversification of these operating systems can increase factors causing human error by the ships' operators. However, there is a lack of research on the maneuvering methods, considering the inherent active characteristics of each type of water jet. In this paper, we analyze the sideway method suitable for the condition of Coast Guard Exclusive wharf without assistance, based on the astern performance of each type. Then, a ship handling simulator was used for the experiment; they compared and verified through interviews of captains.